MHMostafa Karimi Hajiabadi

Mostafa Karimi Hajiabadi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mostafa Karimi Hajiabadi has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Single-Phase Symmetric-Bipolar Buck-Boost AC-AC Converter With Continuous Input-Output Current

    by Mostafa Karimi Hajiabadi, Ali Mosallanejad, Ahmad Salemnia, Alireza Lahooti Eshkevari

    This article presents a novel single-phase, nonisolated buck-boost AC-AC converter featuring lower active and passive components compared with the existing designs. The proposed topology offers symmetric in-phase and antiphase buck-boost voltage operations, as well as a step-changed output voltage frequency, making it suitable for a broad range of applications, such as dynamic voltage restorers (DVR). The offered converter features only two magnetic elements, one on the input side and another on the output side, which ensure continuous input and output currents and lower total harmonic distortions (THD) in both input and output currents compared with the existing designs. The proposed AC-AC converter lacks coupled inductors, eliminating the need for RC snubbers on power switches. Additionally, it inherently achieves safe commutation by avoiding bidirectional AC switches and discarding dead- or overlap times from the commutation strategy. Comparative assessments indicate that the proposed topology performs better than its counterpart circuits in terms of switching device power (SDP) index, volumetric indexes of capacitors and magnetic components, efficiency, and input and output THD currents. The experimental results demonstrate an efficiency of 95.6% and a THD of less than 2.5%.


  • Efficient High-Frequency Isolated Buck-Boost Matrix Converters With Reduced Components and Continuous Input Current

    by Alireza Lahooti Eshkevari, Hafiz Furqan Ahmed, Iman Abdoli, Mostafa Karimi Hajiabadi

    This article develops two circuit variations of a new single-phase high-frequency transformer-isolated (HFTI) buck boost matrix converter (MC). Both MCs feature continuous input current, with one topology providing continuous output current and another reducing component count further. These MCs offer symmetric bipolar voltage gain, supporting both inverting and noninverting output voltages, as well as an output voltage with step-change frequency and rectification. The adjustable bipolar buck-boost output of the converter, step-variable frequency operation, and voltage rectification capability make it suitable for high-gain traction systems, rectification, and use in dynamic voltage restorer (DVR) applications. Key advantages include substantial component reduction, low total harmonic distortion (THD) in both input and output currents, enhanced magnetic utilization, and the ability to operate with various winding ratios without compromising the buck-boost function or its voltage range. Additionally, integrating an HFT in both topologies eliminates the need for line-frequency transformers, enabling more efficient grid integration. Both MCs also benefit from inherent commutation. The comparative evaluations confirm that the proposed MCs perform better than existing designs in terms of maximum switch voltage, switch utilization factor, efficiency, and volumetric performance. The paper presents the operating principle of the proposed MCs, followed by experiments to verify their operation and performance.

  • A Three‐Port Quadratic Step‐Up DC–DC Converter With High Gain and Continuous Input Current

    by Mostafa Karimi Hajiabadi, Alireza Lahooti Eshkevari, Ali Mosallanejad, Ahmad Salemnia

    This article presents a new three‐port step‐up DC–DC converter with two input ports and one output terminal. This converter structure achieves a higher voltage conversion ratio and better switching device power (SDP) than its multi‐input counterpart circuits. Using the “quadratic” approach to reach high voltage gains and discarding coupled inductors from the topology have avoided voltage spikes on power switches, resulting in higher efficiency compared to other hard‐switched multi‐input counterparts. In addition, the proposed converter can transmit power from one or both inputs to the output, from the output to the inputs, or between the inputs. Besides, common ground and continuous input current for all input ports are two distinct features of the suggested topology that most multi‐input converter structures lack. This paper thoroughly explains the converter operation and confirms its performance using laboratory experiments on a 200‐W hardware prototype. This new topology has been compared with existing competitors, considering several indicators. Comparative studies show that the proposed topology outperforms in terms of gain and SDP. Laboratory results validate the above achievements and exhibit that the maximum achievable efficiency by this method is 94.1%. This converter is suggested for electric vehicles and microgrid applications.


  • A Novel Family of Single‐Phase Direct Buck AC‐AC Converters With Continuous Input Current, Reduced Components, and Balanced Power Losses

    by Alireza Lahooti Eshkevari, Iman Abdoli, Mostafa Karimi Hajiabadi

    This paper introduces a single‐phase step‐down AC‐AC converter designed for voltage sag/swell compensation applications. The converter features a minimal component count, continuous input current, and high efficiency, although only one power switch operates at a high frequency per input voltage half‐cycle. It offers a linear and broad voltage conversion ratio (D) without right‐half‐plane zeros in its small‐signal transfer function, simplifying the controller design. The proposed converter does not need dead time. It ensures balanced voltage and current stresses and power losses among power switches, easing the selection of semiconductors. Compared with existing topologies, it excels in total capacitor voltage, switching device power, and volume metrics of capacitors and inductors, thereby reducing cost and size. Experimental results from a 250‐W prototype demonstrate a peak efficiency of 94.8% and effective voltage sag/swell mitigation as a DVR.

  • Open Access

    High step‐up direct ac‐ac boost converter with optimal component counts based on SEPIC

    by Alireza Lahooti Eshkevari, Iman Abdoli, Mostafa Karimi Hajiabadi, Ali Mosallanejad

    This paper introduces a new direct step‐up ac‐ac converter designed based on the SEPIC. It provides a higher step‐up conversion ratio than other counterparts with valuable features like high efficiency, reasonable input and output total harmonic distortions (THD), continuous input current waveform, common ground, few components, and single‐stage conversion without snubber and LC filters. Unlike most counterparts, the duty cycle can be varied between zero and one in boost operation and is not limited to any value below one. The voltage stress on one switch is reduced by increasing the winding coefficient of the utilized coupled inductor, and current stress on another is independent of this coefficient. It reduces the switches' losses and improves the converter efficiency. Thanks to the above attributes, the proposed converter is suitable for inductive power transfer from low‐voltage ac sources, operating as an ac voltage regulator for sensitive ac loads, and any applications that require a boost converter with few components. This article shows the converter's operation principle and evaluates its performance through experiments on a 225 W prototype. Accordingly, the maximum obtained efficiency is 95.4%. The input and output current THDs for the nominal inductive load equal 4.5 and 2.8%, respectively. Results confirm the claims.


  • Open Access

    A high step‐up coupled‐inductor‐based dc‐dc converter with a wide duty cycle range and improved gain‐to‐element ratio

    by Mostafa Karimi Hajiabadi, Alireza Lahooti Eshkevari, Iman Abdoli, Ali Mosallanejad, Ahmad Salemnia

    Most high‐gain step‐up dc‐dc structures operate with a limited duty cycle and suffer from a high component count, limiting their application. This paper addresses these problems by proposing a new step‐up dc‐dc converter that provides a high conversion ratio with few elements. Two coupled inductors are used instead of conventional voltage multiplier cells to improve the gain without excessive components. The topology includes one switch whose duty cycle is not limited and can vary between zero and one according to the output voltage condition. It has been placed on the low‐voltage side of the converter that encounters low‐voltage stress. It is selected from low‐voltage rating switches with small on‐resistance, which reduces the conduction loss of the switch and improves the efficiency. High boost factor, high efficiency, reasonable component counts, improved gain‐to‐element ratio, and low voltage stress on the switch distinguishe the converter from their counterparts. The topology also benefits from the common‐ground feature. However, its input current waveform is pulsating. This article describes the theory and operation principle of the topology in detail. Experimental results are represented to evaluate the converter's performance and operation. In this case, a 240 W prototype has been designed and fabricated. Results confirm the above claims.


  • Open Access

    Ultra‐high gain quadratic boost DC–DC converter based on a three‐winding coupled inductor with reduced voltage stress for fuel cell‐based systems

    by Mostafa Karimi Hajiabadi, Ali Mosallanejad, Ahmad Salemnia

    Here, an ultra‐high gain quadratic boost DC–DC converter (UQBC) based on the conventional quadratic boost converter (CQBC) and a three‐winding coupled inductor (TWCI) has been proposed. It benefits from an extensive voltage gain range and low voltage stress on semiconductors. In addition, the converter requires a reasonable number of components. This structure is suitable for connecting renewable DC power sources like fuel cells to a DC‐bus in DC microgrids. Unlike CQBC, the produced conversion ratio has been improved to [1 +n+m+d (1 +n )]/(1 −d ) 2 thanks to integrating a TWCI into CQBC. As a result, the proposed quadratic boost converter gives a better step‐up factor than previously presented quadratic boost converters (QBC). Meanwhile, the employed improvement method has not adversely affected some critical parameters like voltage stress on semiconductors or the input current ripple. This paper presents the mathematical analysis and operating principle of the proposed topology for both continuous and discontinuous current modes (CCM and DCM). Experimental results are represented to validate the converter theory and its performance. Results indicate that a high gain and efficiency have been obtained. Also, the voltage stress on the power switch is reduced by one‐fourth by choosing a proper duty cycle and winding coefficient.


  • A quadratic step‐up dc‐dc converter with high gain, reduced voltage stress, and component counts

    by Mostafa Karimi Hajiabadi, Alireza Lahooti Eshkevari, Iman Abdoli, Ali Mosallanejad, Ahmad Salemnia

    Summary: It is safe to say that the topic of step‐up dc–dc converters is one of the most popular issues in power electronics. Since the demand for high‐gain and high‐efficiency converters with optimal component counts has increased drastically, more new step‐up topologies have been innovated. Continuing past efforts, the paper proposes a new single‐switch non‐isolated step‐up dc–dc converter based on the basic quadratic boost converter (QBC). High boost factor, high efficiency, continuous input current, reduced voltage stresses on the switch and power diodes, and an appropriate required number of elements compared to the obtained boost factor are the most significant achievements of this topology, which satisfy most of the essential design goals. Compared to the basic QBC, the voltage gain has been increased five times further by integrating a new coupled inductor–capacitor‐based impedance network into the basic quadratic circuit. In this article, the theory and operating principle of the topology for both continuous and discontinuous current modes (CCM and DCM) are discussed in detail. To verify the theory, experimental results are also presented. Results show that the converter has reached 12 times gain, about 95% efficiency, and up to one‐third less voltage stresses on semiconductors.