DBDmytro Brega

Dmytro Brega

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dmytro Brega has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    БЕЗКОНТАКТНИЙ ДИСТАНЦІЙНИЙ ГАЗОДЕТОНАЦІЙНИЙ РОЗМІНОВУВАЧ: ПРОЄКТУВАННЯ, ДОСЛІДЖЕННЯ, НАПРЯМИ ПІДВИЩЕННЯ ПРОДУКТИВНОСТІ

    by Ольга Володимирівна Шипуль, Олексій Анатолійович Павленко, Дмитро Андрійович Брега, Олександр Миколайович Застела

    Предметом дослідження є принципи проєктування газодетонаційної установки безконтактного розмінування, спрямовані на забезпечення її працездатності, продуктивності та живучості конструкції. Метою роботи є розроблення науково обґрунтованої конструкції газодетонаційної установки для безконтактного знешкодження мін натискної дії та визначення конструктивних і компонувальних рішень, спрямованих на підвищення продуктивності процесу розмінування. Завдання дослідження полягають в обґрунтуванні газодетонаційного принципу безконтактного ініціювання мін натискної дії; чисельному дослідженні процесів формування та поширення ударної хвилі; визначенні параметрів імпульсного навантаження та геометрії зони ефективного впливу; обґрунтуванні конструктивних параметрів і багатоканального компонування установки; встановленні взаємозв’язку між розташуванням виконавчих секцій, частотою їх спрацьовування та швидкістю руху розміновувального комплексу. Отримано такі результати: розроблено та обґрунтовано конструктивну й компонувальну схеми газодетонаційної установки безконтактного розмінування та визначено основні геометричні параметри її виконавчих елементів. За результатами CFD-моделювання підтверджено можливість формування спрямованого короткочасного імпульсного навантаження на віддалену поверхню. На відстанях 0,5 – 1,0 м розраховані значення імпульсу надлишкового тиску становлять 172 – 250 Па·с для основної контрольної області діаметром 150 мм та 87 – 126 Па·с для периферійної області діаметром 300 мм. Мінімальне отримане значення 87 Па·с більш ніж удвічі перевищує встановлений у попередніх дослідженнях орієнтовний пороговий рівень близько 40 Па·с для дослідженого типу натискного підривника, що підтверджує достатність сформованого навантаження за імпульсним критерієм. Визначено геометричні параметри зони впливу окремої секції та обґрунтовано принцип формування суцільної смуги впливу шляхом взаємного перекриття робочих зон. Встановлено, що зона впливу одноствольної секції має розміри близько 880×590 мм, а для формування суцільної смуги впливу шириною близько 4 м необхідне лінійне розташування 12 таких секцій із перекриттям сусідніх зон близько 50 %. За робочої частоти 2 Гц та 50 %-го поздовжнього перекриття максимальна розрахункова швидкість руху комплексу становить 0,88 м/с (близько 3,2 км/год). Наукова новизна полягає в обґрунтуванні принципу формування суцільної зони безконтактного імпульсного впливу багатоканальною газодетонаційною системою та встановленні взаємозв’язку між параметрами ударно-хвильового навантаження, геометрією та перекриттям робочих зон і продуктивністю комплексу. Запропоновано модульний принцип групування газодетонаційних стволів для збільшення зони впливу та підвищення продуктивності розмінування.

  • Open Access

    ПРОЕКТУВАННЯ ЛЕГКОГО ДОЗВУКОВОГО БЕЗПІЛОТНОГО ЛІТАЛЬНОГО АПАРАТУ З РЕАКТИВНОЮ СИЛОВОЮ УСТАНОВКОЮ

    by Дмитро Брега, Василь Бахін, Павло Шабанов, Андрій Гуменний

    У статті розглянуто сучасні тенденції розвитку безпілотних літальних апаратів, зокрема літакового типу з реактивними силовими установками. Показано, що досвід бойових дій в Україні та світі підтверджує ключову роль безпілотників у військовій і цивільній сферах. Проведено аналіз переваг і обмежень використання двигунів внутрішнього згоряння, електричних та реактивних установок, із виокремленням особливостей малих турбореактивних двигунів для одноразових ударних безпілотних апаратів. Здійснено попереднє проєктування зразка реактивного безпілотного літального апарата із заданими тактико-технічними характеристиками, зокрема визначено масові параметри, геометрію крила та фюзеляжу, схему хвостового оперення, а також проведено розрахунок аеродинамічних характеристик за допомогою програмного комплексу Ansys Fluent. Отримані результати дали змогу побудувати поляру літального апарату та оцінити аеродинамічну ефективність у діапазоні дозвукових швидкостей. У статті обґрунтовано доцільність використання доступних малих турбореактивних двигунів серійного виробництва, зокрема Swiwin 300B, для створення оперативно-тактичних безпілотних літальних апаратів. Наведені розрахунки підтверджують можливість досягнення необхідної дальності, швидкості та корисного навантаження при збереженні простоти конструкції й відносно низької вартості. Отримані результати можуть бути використані у подальшому вдосконаленні методів розрахунку та оптимізації конструкції безпілотних літальних апаратів.

  • Open Access

    Investigation of shock wave effect on activation of a pressure-sensitive landmine fuse

    by Vitalii Myntiuk, Olga Shypul, Oleksiy Pavlenko, Denys Tkachenko, Vadym Garin, Dmytro Brega

    The study investigates how shock wave parameters, specifically impulse and pressure amplitude, affect the fuse of a landmine. This research is driven by the need to develop an effective method for contactless gas detonation demining. In this method, detonating a gas mixture within demining device...


  • Open Access

    Моделювання процесу утворення паливної суміші в каналі газодетонаційного розміновувача

    by Olga Shypul, Oleksii Pavlenko, Dmytro Brega, Vadym Garin, Oleg Tryfonov

    The gas-dynamic process of cyclic fuel mixture formation and filling it into the deminer channel is the subject of the study. This study aims to minimize the deviations of the mixture parameters from the stoichiometric composition determine the quantity, required consumption characteristics, and spatial position of the supply valves for fuel and oxidizer. The objectives of this study are to conduct numerical experiments on filling the deminer channel with the fuel mixture and to assess the quality of the resulting mixture, considering the limitations on the filling time. To solve this problem, a mathematical model of the physical process of mixing fuel components must be developed, considering the features of the gas-dynamic flow in the channels. The following results were obtained: a design of a cyclic mixture formation system that satisfies the functional requirements for the deminer’s operability, namely: filling time of 0.05 s and stoichiometric composition, was proposed. The homogeneity of the formed mixture was indirectly confirmed by experimental tests by comparing the maximum temperature values with those theoretically achievable for an ideal mixture. A qualitative and quantitative assessment of the proposed design’s technical solution is given. A mathematical model of the mixture generation process with a given component composition is created, and a series of numerical experiments are conducted. The modeling is performed using the ANSYS Fluent software. The calculation is performed in a non-stationary setting. The obtained values of the gas flow rate, pressure field, and temperature, the requirements for the valves, and their consumption characteristics are determined based on the calculation results. The modeling results showed that the proposed design solutions regarding the number, type, and mutual arrangement of the oxidant and fuel supply valves provide the required channel filling rate while maintaining the stoichiometric composition, which ensures stable combustion of the mixture in the detonation mode. The stoichiometric composition of the gas mixture was achieved with an accuracy of not less than 3%. The scientific novelty of the obtained results lies in determining the relationship between the geometric and gas-dynamic parameters of the mixer, which allows obtaining a mixture with the necessary characteristics of homogeneity for the vortex mixing method. The component composition was analyzed both in the pre-detonation chamber and in the deminer’s main channel. The ingress of oxygen into the main channel can become an additional trigger of detonation processes, which can be simulated based on the proposed mathematical model.

  • Comparative Analysis for Different Turbulence Modelling Approaches in Combustion Simulation

    by Dmytro Brega, Oleg Tryfonov, Olga Shypul, Vadim Garin, Oleksii Pavlenko


  • Open Access

    Дослідження розповсюдження тріщини в зонах концентраторів напружень під дією термоімпульсного навантаження в деталях з ливарними дефектами

    by Olga Shypul, Vitalii Myntiuk, Denys Tkachenko, Oleksiy Pavlenko, Dmytro Brega, Yevgen Tsegelnyk

    The subject of the study is the processes of crack formation under the action of thermal pulse loads on the example of a body part of an aviation unit. The aim of the work is to determine the influence of existing stress concentrators in parts obtained by the casting method on the possibility of their processing by the thermal pulse method. The main tasks of the study include establishing the regularities of crack development depending on the geometric concentrators of parts and imposing restrictions on the modes of thermal pulse processing. The methods of the study include methods of mathematical modeling of the problem of thermoelasticity during thermal pulse loading and modeling of brittle fracture in the zone of the highest stress concentration with the determination of stress intensity coefficients for the case of normal separation, transverse and longitudinal displacements and the J-integral. Verification of the calculation models is based on the criterion of calculation coincidence and determination of the optimal size of finite elements of the calculation areas on test problems. As a result of the study, the dependences of crack opening on the sizes of geometric stress concentrators were determined, taking into account the presence of pores in the metal structure of the casting part. The conclusions provide recommendations for the use of the obtained regularities. Further research should be focused on improving the method for assigning modes of thermal pulse processing of parts from the point of view of the crack resistance of the part structure.

  • Open Access

    Створення концептуальної моделі газодетонаційного розміновувача

    by Oleksiy Pavlenko, Olga Shypul, Vitalii Myntiuk, Denys Tkachenko, Dmytro Brega, Vadym Garin

    The subject of this study is the neutralization processes of mines and other explosive devices, as well as the equipment created based on these processes. The urgent need for effective solutions is due to the significant contamination of Ukrainian territory with explosive objects, which requires the use of modern technologies for humanitarian demining. The aim of this work is to develop a conceptual model of an effective, safe, autonomous, and economical gas-detonation deminer that can provide long-term operation without refueling or additional maintenance. The main objectives of the study include an analysis of existing demining methods, identification of their advantages and disadvantages, selection of the optimal approach for the development of equipment, as well as the creation of a preliminary design and formation of a structural diagram of the device. During the work, a review of traditional contact and non-contact demining methods was conducted. It was established that the shock-wave method is the most suitable method for humanitarian demining; however, modern installations have significant drawbacks: the use of disposable explosive materials, high cost, low accuracy, and limited capabilities. Because of this research, the principles of operation and design of a gas-detonation deminer based on the use of detonation tubes were proposed. The main source of shock waves is the combustion process of fuel-oxygen and fuel-air mixtures in two separate combustion chambers. This approach reduces risks and ensures stable device operation. A three-dimensional model of the main body of the deminer was developed considering its compactness, maintainability, and safety requirements under explosion exposure conditions. The conclusions emphasize the use of the gas detonation method as a promising solution for humanitarian demining because of its efficiency, ease of operation, continuity of the technological process, and low cost of consumables. The present work is aimed at solving the current problems of clearing large territories of Ukraine contaminated with explosives, which will significantly accelerate humanitarian demining processes and reduce costs.


  • Open Access

    Devising a calculation method for modern structures of current-conducting elements in large electric machines in a three-dimensional statement

    by Oleksii Tretiak, Stanislav Kravchenko, Serhii Smakhtin, Dmytro Brega, Anton Zhukov, Serhii Serhiienko, Yevhen Don

    The jumpers of rotor pole-to-pole connections are highly stressed elements in a hydraulic generator structure. These assemblies often fail due to deformation that exceeds the size of an air gap. Existing methods do not take into account the thermal component and attempts to improve the design are not based on mathematical models that make it possible to perform calculations with an accuracy of more than 50 %. The method devised in this work makes it possible to obtain boundary conditions of the third kind on the basis of three-dimensional mathematical modeling of the ventilation system of the hydraulic unit without simplifications. The method accuracy is explained by taking into account the spatial thermal component. The heat transfer coefficient determined by this method in the pole-to-pole connections area was ~250 W/(m2·K). Using FEM, mathematical modeling of the thermal stress state of pole-to-pole connections was carried out, taking into account mechanical and thermal factors. This made it possible to design the improved connection structure with additional fastening elements, which make it possible to reduce the displacement to 0.03 mm, and the stress to 53 MPa at the rotor rotation frequency of 880 rpm. This design makes it possible to enable reliable operation of the hydraulic unit under the condition of increasing the rotor rotation frequency to overspeed with disconnected combinatorial dependence, provided that the actual stresses are 0.95 % of the material yield strength. The convergence of the values obtained by the proposed method and by the HSS method exceeded 99 %. The practical result is the proposals for the hydraulic generator design modernization