OMOleksandr Matviiuk

Oleksandr Matviiuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleksandr Matviiuk has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Operation of Silor-Modified Wood in Acidic Environments: An Experimental Study

    by Oleksandr Matviiuk, Sviatoslav Homon, Oleksiy Petrenko, Svitlana Vikhot


  • Open Access

    ANALYSIS OF TEST EQUIPMENT FOR INVESTIGATION OF MATERIALS UNDER A STRONG LOAD APPLICATION

    by Sviatoslav Homon, Oleksandr Matviiuk, Leonid Kulakovskyi, Nataliya Chornomaz

    An analysis of publications on this topic. It is established that in most literature sources the work of wood is shown only in the ascending branch of deformation, which is a false statement. The method of experimental studies of alder and spruce wood by axial compression along the fibers with a short-term load at standard humidity (by increasing displacements) is presented. The age of the wood was about 40 years. Experimental studies of such samples were performed on a modern STM- 100 test machine. 18 samples with a cross section of 30x30x120 mm were tested. Based on the experiment, complete deformation diagrams “stress σc - strain uc” were constructed and the main parameters were established: critical and residual strains, as well as their corresponding stresses. It is established that both diagrams have an ascending and descending branch, ie they work in both pre-critical and super-critical stages of work. The average critical deformations of alder wood uc,0,d = 0,00397, as well as the corresponding maximum stresses fc,0,d = 35,6 MPa, and spruce wood - uc,0,d = 0,00421 (fc,0,d = 38.1 MPa). Also, the average residual deformations for alder wood uc,fin = 0.277, and the corresponding stresses σc,fin = 3.9 MPa; for spruce wood uc,fin = 0.212, and stress - σc,fin = 3.6 MPa. It is confirmed that deciduous and coniferous wood at standard humidity has an ascending and descending branch, ie works in the subcritical and supercritical stages of work. In the future it is necessary to conduct such experimental studies for other deciduous and coniferous species. In the future, determined mechanical characteristics experimentally, it is necessary to propose methods for finding and theoretical, which will give a complete picture of such materials.

  • Open Access

    IMPROVEMENT OF MECHANICAL PROPERTIES OF WOOD AT THE ACCOUNT OF THEIR ADHESIVE

    by Sviatoslav Homon, Svyatoslav Gomon, Oleksandr Matviiuk, Nataliya Chornomaz

    Наведено методику досліджень клеєної деревини різних порід осьовим стиском уздовж волокон короткочасним навантаженням за стандартної вологості (за приростом переміщень). Побудовано повні діаграми деформування «напруження σс - деформації uc» та встановлено основні параметри: максимальні наруження, критичні деформації, початковий модуль пружності. Встановлено, що склеювання деревини збільшує міцність та початковий модуль пружності композиційного матеріалу та залежить від товщини доски.

  • Open Access

    ANALYSIS OF TEST EQUIPMENT FOR INVESTIGATION OF MATERIALS UNDER A STRONG LOAD APPLICATION

    by Sviatoslav Homon, Tetiana Dovbenko, Oleksandr Matviiuk, Oleg Vereshko, Leonid Kulakovskyi, Natalya Chornomaz

    An analysis of modern testing equipment to establish the mechanical properties of different in structure and origin of building materials. As a result, it was established, that the most effective for testing are foreign electromechanical and servo-hydraulic machines of different configurations. It is determined that this type of technical systems allows to study different types of materials, including high-strength, compressive, tensile, bending and other types of loads in accordance with current international regulations. The article analyzes the principles of operation of the universal test machine INSTRON and the universal servo test machine UIT STM 100S. The configuration of such modern technical systems involves the availability of electronic computers and software, which allows testing in automatic mode, program research factors, determine the current and maximum values of mechanical properties of building materials, perform mathematical calculation of characteristics, reproduce information on the device screen, build research diagrams in electronic and printed form. It has been found that the advantages of such test machines are a load of up to 60 tons. It was determined that the universal machine UIT STM 100S is characterized by a large traverse stroke and a wide range of test speeds, which allows to expand the solution of quality control problems in industry. It is also established that the UIT STM 100S has software that includes a standard library of test methods according to regulatory documentation. The advantages of such a machine are the possible expansion of the standard information base necessary for the operation of the standards or the installation of an additional software module that provides the ability into independently supplement the standard library. Given the wide range of measurements of the universal testing machine UIT STM 100S, we envisage its use for the study of deciduous and coniferous wood in modern rigid test mode.