Turan Ozturan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Turan Ozturan has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Nilufer Ozyurt
Department of Civil Engineering, Bogazici University, Bebek, Istanbul, Turkey
5 shared publications - Onur Ozturk
Cornell University
3 shared publications - Anıl Niş
Department of Civil Engineering, Istanbul Gelisim University
2 shared publications - Erhan Güneyisi
Department of Civil Engineering, Harran University, Şanlıurfa, Turkey
2 shared publications - Hasan Yildirim
Department of Civil Engineering and Management, University of Manchester, Manchester M13 9PL, UK
2 shared publications - Ahmet Onur Pehlivan
Assistant Professor, Dept. of Civil Engineering, Maltepe Univ., Istanbul 34857, Turkey. ORCID:
1 shared publication
Latest Publications
- 24 April 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Post-Cracking Cyclic Shear Performance of Recycled Aggregate Concrete for Pavements
Recycling construction and demolition waste is a widely used approach to enhance the sustainability of construction materials. Pavements, with their large scale, have a considerable impact on the environment during their construction and use phases. The potential of using recycled aggregates to reduce the environmental impact of concrete pavements has been discussed in several previous studies considering various aspects. However, the cyclic shear performance of concrete mixtures (one of the main parameters affecting pavement performance) produced with recycled aggregates has only been roughly discussed in a limited number of studies. To address this issue, concrete mixtures with varying recycled aggregate replacement ratios were designed and tested in this study for basic engineering properties and post-cracking cyclic shear performance. The impact of varying recycled aggregate amounts on performance parameters was assessed through experimental studies, and variations in the measured parameters are discussed. Recommendations are provided for practical applications and future research.
- 24 April 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Post-Cracking Cyclic Shear Performance of Recycled Aggregate Concrete for Pavements
Recycling construction and demolition waste is a widely used approach to enhance the sustainability of construction materials. Pavements, with their large scale, have a considerable impact on the environment during their construction and use phases. The potential of using recycled aggregates to reduce the environmental impact of concrete pavements has been discussed in several previous studies considering various aspects. However, the cyclic shear performance of concrete mixtures (one of the main parameters affecting pavement performance) produced with recycled aggregates has only been roughly discussed in a limited number of studies. To address this issue, concrete mixtures with varying recycled aggregate replacement ratios were designed and tested in this study for basic engineering properties and post-cracking cyclic shear performance. The impact of varying recycled aggregate amounts on performance parameters was assessed through experimental studies, and variations in the measured parameters are discussed. Recommendations are provided for practical applications and future research.
- Open Access
- 2 May 2022
- Published by MDPI AG in Engineering Proceedings
- Vol. 17 (1) , 27
Mechanical Properties and Structural Requirements of Recycled Aggregate Concrete for Pavements
In recent years, the recycling of waste materials has attracted considerable attention due to the scarcity of natural resources on earth
- 2 May 2022
- Published by MDPI AG in Engineering Proceedings
- Vol. 17 (1) , 27
Open AccessMechanical Properties and Structural Requirements of Recycled Aggregate Concrete for Pavements
In recent years, the recycling of waste materials has attracted considerable attention due to the scarcity of natural resources on earth
- 28 February 2022
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (14) , 5239-5253
Evaluation of mechanical properties and structural behaviour of concrete pavements produced with virgin and recycled aggregates: an experimental and numerical study
Due to the large-scale use of materials in highways, the sustainability of materials has attracted considerable interest for years. In this respect, significant effort has been spent investigating the use of recycled aggregates in concrete pavements. This study has been carried out to fill the gap in the structural performance of recycled aggregate concrete pavements. First, properties of concrete mixtures, produced with virgin, recycled concrete and recycled brick aggregates were experimentally measured, and the results were compared. Then, finite element analyses were done by following a novel methodology that considers the well-known previous works. Results showed that replacement of coarse aggregates with recycled aggregates decreases the mechanical properties in various amounts. Due to the resulting performances, for the same slab thickness, decreased maximum stress, increased deflection and stress ratio values were found for recycled aggregate mixtures. Additionally, higher thicknesses and material requirements were found for recycled aggregate concrete for a similar life. Despite the decreased performance and increased material requirements, the use of recycled aggregates in pavements can still be a viable alternative for countries with limited natural resources and landfills. Therefore, based on the findings, several important discussions and suggestions were presented for future works.
- 28 February 2022
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (14) , 5239-5253
Evaluation of mechanical properties and structural behaviour of concrete pavements produced with virgin and recycled aggregates: an experimental and numerical study
Due to the large-scale use of materials in highways, the sustainability of materials has attracted considerable interest for years. In this respect, significant effort has been spent investigating the use of recycled aggregates in concrete pavements. This study has been carried out to fill the gap in the structural performance of recycled aggregate concrete pavements. First, properties of concrete mixtures, produced with virgin, recycled concrete and recycled brick aggregates were experimentally measured, and the results were compared. Then, finite element analyses were done by following a novel methodology that considers the well-known previous works. Results showed that replacement of coarse aggregates with recycled aggregates decreases the mechanical properties in various amounts. Due to the resulting performances, for the same slab thickness, decreased maximum stress, increased deflection and stress ratio values were found for recycled aggregate mixtures. Additionally, higher thicknesses and material requirements were found for recycled aggregate concrete for a similar life. Despite the decreased performance and increased material requirements, the use of recycled aggregates in pavements can still be a viable alternative for countries with limited natural resources and landfills. Therefore, based on the findings, several important discussions and suggestions were presented for future works.
- 1 November 2020
- Published by Teknik Dergi in Teknik Dergi
- Vol. 31 (6) , 10315-10337
Corrosion and Chloride Diffusivity of Reinforced Concrete Cracked under Sustained Flexure
This research discusses the chloride diffusivity of concrete as well as corrosion performance of rebars in cracked and uncracked states. Prismatic concrete specimens with two water-to-cement ratios, two concrete cover thicknesses with and without steel fibers were used. Three-point flexural loading was applied to form cracks and cracks were sustained by a bolt system. Half-cell potential and corrosion rate measurements were carried out following wetting - drying cycles in chloride environment which were continued for 80 weeks. The positive effects of lower water-to-cement ratio and greater cover depth were found to be surpassed by existence of cracks in concrete.
- 1 November 2020
- Published by Teknik Dergi in Teknik Dergi
- Vol. 31 (6) , 10315-10337
Corrosion and Chloride Diffusivity of Reinforced Concrete Cracked under Sustained Flexure
This research discusses the chloride diffusivity of concrete as well as corrosion performance of rebars in cracked and uncracked states. Prismatic concrete specimens with two water-to-cement ratios, two concrete cover thicknesses with and without steel fibers were used. Three-point flexural loading was applied to form cracks and cracks were sustained by a bolt system. Half-cell potential and corrosion rate measurements were carried out following wetting - drying cycles in chloride environment which were continued for 80 weeks. The positive effects of lower water-to-cement ratio and greater cover depth were found to be surpassed by existence of cracks in concrete.
- 1 April 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 32 (4)
Variation of Flexural Performance Parameters Depending on Specimen Size and Fiber Properties
The use of steel fiber–reinforced (SFR) cement based materials for semistructural applications is expected to increase because some design codes propose such methods for design. The first step for the steel fiber–reinforced concrete (SFRC) design is using correct parameters for material properties. The behavior of concrete under compression and tension is evaluated by using standards. The tension behavior of concrete materials is evaluated, most of the time, via bending tests because these tests are relatively less cumbersome when compared to direct tensile tests. The existing standards/codes suggest using different geometries and set-ups for evaluating bending performance because very different geometries are being used in the structural design. Studies have been conducted by researchers to understand the parameters affecting the results obtained from the bending tests. In this study, the effects of varying shear span-to-depth ratios ( ) and specimen depth to steel fiber length ratios ( ) on the most used design parameters [i.e., the equivalent bending strength (EBS) and bending strength ratio (EBR)] were studied with different steel fiber types and amounts, and the results were discussed based on current standards limitations on size and the ratio. A thorough evaluation of the fresh and hardened state properties was carried out for a full understanding of material properties, and a detailed fiber orientation density analysis was also done for the correct evaluation of the flexural test results.- 1 April 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 32 (4)
Variation of Flexural Performance Parameters Depending on Specimen Size and Fiber Properties
The use of steel fiber–reinforced (SFR) cement based materials for semistructural applications is expected to increase because some design codes propose such methods for design. The first step for the steel fiber–reinforced concrete (SFRC) design is using correct parameters for material properties. The behavior of concrete under compression and tension is evaluated by using standards. The tension behavior of concrete materials is evaluated, most of the time, via bending tests because these tests are relatively less cumbersome when compared to direct tensile tests. The existing standards/codes suggest using different geometries and set-ups for evaluating bending performance because very different geometries are being used in the structural design. Studies have been conducted by researchers to understand the parameters affecting the results obtained from the bending tests. In this study, the effects of varying shear span-to-depth ratios ( ) and specimen depth to steel fiber length ratios ( ) on the most used design parameters [i.e., the equivalent bending strength (EBS) and bending strength ratio (EBR)] were studied with different steel fiber types and amounts, and the results were discussed based on current standards limitations on size and the ratio. A thorough evaluation of the fresh and hardened state properties was carried out for a full understanding of material properties, and a detailed fiber orientation density analysis was also done for the correct evaluation of the flexural test results.- 1 February 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (2)
Microstructural and Mineralogical Characterization of Artificially Produced Pellets for Civil Engineering Applications
Most hazardous, industrial waste from thermal coal-fired power plants has found utilization opportunities in different civil engineering applications by various treatment operations in recent years. Such initiatives provide improvements in economy, environmental protection, and health safety. One of the techniques used in treatment of powdered wastes is to make pellets by pelletization discs. These artificial pellets are mainly used in many structural applications as aggregate in concrete, filling material for roads and foundations, drainage and infiltration material, and so on. In this study, artificially produced pellets from mixtures of fly ash, bentonite, and powdered window glass were sintered at different temperatures to obtain desirable properties. Microstructure of these sintered pellets were investigated in order to understand the changes due to the sintering agent type, content, and sintering temperature. For this purpose, thermal, mineralogical, and microstructural studies were performed. It was noted that sintering temperature and the type and amount of the sintering agent had a remarkable effect on the changes in the microstructure of the pellets. X-ray diffraction (XRD) patterns also showed that sintering produced new crystalline phases not found in the raw materials which was also detected in differential thermal analysis (DTA). Thus, the dissimilar sintering behavior is attributed to the combined effect of crystal structure, morphological characteristics, and oxide compositions of the powder materials used in the production of the pellets.
- 1 February 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (2)
Microstructural and Mineralogical Characterization of Artificially Produced Pellets for Civil Engineering Applications
Most hazardous, industrial waste from thermal coal-fired power plants has found utilization opportunities in different civil engineering applications by various treatment operations in recent years. Such initiatives provide improvements in economy, environmental protection, and health safety. One of the techniques used in treatment of powdered wastes is to make pellets by pelletization discs. These artificial pellets are mainly used in many structural applications as aggregate in concrete, filling material for roads and foundations, drainage and infiltration material, and so on. In this study, artificially produced pellets from mixtures of fly ash, bentonite, and powdered window glass were sintered at different temperatures to obtain desirable properties. Microstructure of these sintered pellets were investigated in order to understand the changes due to the sintering agent type, content, and sintering temperature. For this purpose, thermal, mineralogical, and microstructural studies were performed. It was noted that sintering temperature and the type and amount of the sintering agent had a remarkable effect on the changes in the microstructure of the pellets. X-ray diffraction (XRD) patterns also showed that sintering produced new crystalline phases not found in the raw materials which was also detected in differential thermal analysis (DTA). Thus, the dissimilar sintering behavior is attributed to the combined effect of crystal structure, morphological characteristics, and oxide compositions of the powder materials used in the production of the pellets.
- 1 September 2011
- Published by Elsevier in Composites Part B: Engineering
- Vol. 42 (6) , 1517-1524
Examining the electrical properties of plain and blended cement concretes: Relationship between charge passed and initial current
- 1 September 2011
- Published by Elsevier in Composites Part B: Engineering
- Vol. 42 (6) , 1517-1524
Examining the electrical properties of plain and blended cement concretes: Relationship between charge passed and initial current
- 22 September 2007
- Published by Springer Nature
- p. 189-198
PERFORMANCE OF PLAIN AND BLENDED CEMENT CONCRETES AGAINST CORROSION CRACKING
- 22 September 2007
- Published by Springer Nature
- p. 189-198
PERFORMANCE OF PLAIN AND BLENDED CEMENT CONCRETES AGAINST CORROSION CRACKING
- 1 January 1995
- Published by American Concrete Institute
- Vol. 153, 269-282
Properties of Lightweight Aggregate Produced from a High Calcium Fly Ash
- 1 January 1995
- Published by American Concrete Institute
- Vol. 153, 269-282
Properties of Lightweight Aggregate Produced from a High Calcium Fly Ash