Jemitias Chivavava
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jemitias Chivavava has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alison Emslie Lewis
Department of Chemical Engineering, University of Cape Town, Rondebosch, Cape Town 7701, South Africa
8 shared publications - Jacolien Sussens
Department of Chemical Engineering, University of Cape Town, Rondebosch, Cape Town 7701, South Africa
2 shared publications - Anotidaishe Spencer
Crystallization and Precipitation Research Unit, Chemical Engineering Department, University of Cape Town, Cape Town 7700, South Africa
1 shared publication - Jochen Petersen
University of Cape Town
1 shared publication - Jonathan Sibanda
Crystallization and Precipitation Research Unit, University of Cape Town, Cape Town 7700, South Africa
1 shared publication - Samuel Madimetsa Matau1 shared publication
Latest Publications
- Open Access
- 2 February 2026
- Published by MDPI AG in Chemengineering
- Vol. 10 (2) , 21
Yttrium Sulfate Recovery Using Ethanol as Antisolvent in a Fluidized Bed Reactor
Antisolvent crystallization is a promising method for recovering rare earth elements (REEs). While it offers high theoretical yields of Y2(SO4)3·nH2O from aqueous leach solutions, the recovery is constrained by kinetic limitations. This study examined the crystallization of Y2(SO4)3·nH2O in a fluidized bed reactor (FBR) using ethanol, focusing on the effects of the organic-to-aqueous (O/A) ratio and flow rates on yield and crystal properties. O/A ratios of 0.9 and 1.1 were investigated with an initial Y3+ concentration of 0.87 g/L and a crystallization time of 3 h. The system exhibits multiple rate-limiting steps. At low O/A ratios (0.9), extended induction times indicate either nucleation rate-limitations despite high supersaturation or the possible formation of an initial metastable phase, requiring extended crystallization time for near-equilibrium yields. At high O/A (1.1), elevated supersaturation accelerates nucleation and achieves ~82% yield in 3 h; however, crystal growth exhibited a remaining rate limitation. Lower supersaturation and slower mixing at O/A = 0.9 favored growth, producing crystals with D50 > 34 µm. This work explores how operational parameters influence crystallization behavior while achieving practical yields and acceptable crystal characteristics within a reasonable timeframe. The FBR provided controlled operation, enabling consistent product formation and process flexibility.
- 2 February 2026
- Published by MDPI AG in Chemengineering
- Vol. 10 (2) , 21
Open AccessYttrium Sulfate Recovery Using Ethanol as Antisolvent in a Fluidized Bed Reactor
Antisolvent crystallization is a promising method for recovering rare earth elements (REEs). While it offers high theoretical yields of Y2(SO4)3·nH2O from aqueous leach solutions, the recovery is constrained by kinetic limitations. This study examined the crystallization of Y2(SO4)3·nH2O in a fluidized bed reactor (FBR) using ethanol, focusing on the effects of the organic-to-aqueous (O/A) ratio and flow rates on yield and crystal properties. O/A ratios of 0.9 and 1.1 were investigated with an initial Y3+ concentration of 0.87 g/L and a crystallization time of 3 h. The system exhibits multiple rate-limiting steps. At low O/A ratios (0.9), extended induction times indicate either nucleation rate-limitations despite high supersaturation or the possible formation of an initial metastable phase, requiring extended crystallization time for near-equilibrium yields. At high O/A (1.1), elevated supersaturation accelerates nucleation and achieves ~82% yield in 3 h; however, crystal growth exhibited a remaining rate limitation. Lower supersaturation and slower mixing at O/A = 0.9 favored growth, producing crystals with D50 > 34 µm. This work explores how operational parameters influence crystallization behavior while achieving practical yields and acceptable crystal characteristics within a reasonable timeframe. The FBR provided controlled operation, enabling consistent product formation and process flexibility.
- Open Access
- 31 December 2024
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 124 (12) , 737-747
Comparing the recovery of rare earth elements from ion-adsorption clay leach solutions using various precipitants
Rare earth elements (REEs) have special properties that prompted their extensive use in high-tech applications. The demand for REE has, therefore, increased over the past years, resulting in the supply risk of the materials. Extraction from non-conventional low-grade ores, like easy-to-mine ion-adsorption clays (IACs), by hydrometallurgical methods is being explored to supplement the supply of REEs. The extraction of REEs from low tenor IAC leach solutions requires enrichment using cost-effective methods such as precipitation. Therefore, the aim of this study was to understand the recovery of REEs from IAC leach solutions using various reagents for precipitation. In the first part of the study, recoveries of REEs from IAC leach solutions through direct precipitation using H2C2O4 and NH4HCO3, as well as antisolvent crystallization using C2H5OH, were predicted via thermodynamic modelling using OLI Stream Analyzer. Verification experiments were then conducted through the use of an agitated reactor. Simulation results showed that high yields of REEs were possible using each of the reagents, but large quantities of C2H5OH were required. Experimental results confirmed the high yields predicted from simulations. Precipitation with H2C2O4 was found to selectively recover REEs while rejecting Al. However, utilization of NH4HCO3 and C2H5OH resulted in the co-precipitation of Al. Furthermore, the yield of Y from antisolvent crystallization was significantly lower than the theoretical value. The product recovered from antisolvent crystallization consisted of well-faceted, large crystalline particles, which filtered faster than the fine, amorphous REE carbonates recovered using NH4HCO3. REE oxalates were crystalline, larger than the REE carbonates and, overall, showed the highest filtration rate.
- 31 December 2024
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 124 (12) , 737-747
Open AccessComparing the recovery of rare earth elements from ion-adsorption clay leach solutions using various precipitants
Rare earth elements (REEs) have special properties that prompted their extensive use in high-tech applications. The demand for REE has, therefore, increased over the past years, resulting in the supply risk of the materials. Extraction from non-conventional low-grade ores, like easy-to-mine ion-adsorption clays (IACs), by hydrometallurgical methods is being explored to supplement the supply of REEs. The extraction of REEs from low tenor IAC leach solutions requires enrichment using cost-effective methods such as precipitation. Therefore, the aim of this study was to understand the recovery of REEs from IAC leach solutions using various reagents for precipitation. In the first part of the study, recoveries of REEs from IAC leach solutions through direct precipitation using H2C2O4 and NH4HCO3, as well as antisolvent crystallization using C2H5OH, were predicted via thermodynamic modelling using OLI Stream Analyzer. Verification experiments were then conducted through the use of an agitated reactor. Simulation results showed that high yields of REEs were possible using each of the reagents, but large quantities of C2H5OH were required. Experimental results confirmed the high yields predicted from simulations. Precipitation with H2C2O4 was found to selectively recover REEs while rejecting Al. However, utilization of NH4HCO3 and C2H5OH resulted in the co-precipitation of Al. Furthermore, the yield of Y from antisolvent crystallization was significantly lower than the theoretical value. The product recovered from antisolvent crystallization consisted of well-faceted, large crystalline particles, which filtered faster than the fine, amorphous REE carbonates recovered using NH4HCO3. REE oxalates were crystalline, larger than the REE carbonates and, overall, showed the highest filtration rate.
- Open Access
- 10 April 2024
- Published by Elsevier in Separation and Purification Technology
- Vol. 346
The recovery of yttrium sulfate through antisolvent crystallization using alcohols
- 10 April 2024
- Published by Elsevier in Separation and Purification Technology
- Vol. 346
Open AccessThe recovery of yttrium sulfate through antisolvent crystallization using alcohols
- Open Access
Investigation on the Effect of Mesomixing on Crystal Quality during Antisolvent Crystallization of Nd2(SO4)3·8H2O
Rare earth elements (REEs) are essential for permanent magnets that are vital for wind turbines and electric vehicles motors (EV), and are also used in a range of high-tech devices such as smartphones, digital cameras, and electronic displays. Nickel metal hydride (NiMH) batteries have been identified as a potential source due to their short lifespans and an anticipated boom in the production of EV. The aim of this study was to investigate the effect of mesomixing on crystal quality in a non-confined impinging jet mixer (NCIJM) during antisolvent crystallization of 3.2 g/L Nd2(SO4)3 from a synthetic leach solution of NiMH battery using ethanol at an O/A ratio of 1.1. The jet streams were supplied at a Reynolds number (Re) between 7500 and 15,000. The product slurry was allowed to further crystallize in a stirred batch crystallizer at a Re of 13,000 for 45 s. An average yield of 90% was achieved. Laser diffraction and scanning electron microscopy (SEM) were used for size analysis. The initial results were inconclusive due to the secondary mixing effect in the stirred batch crystallizer. Therefore, the experiments were repeated, and samples were collected immediately after mixing in the NCIJM onto a porous grid placed on a high absorbance filter paper to abruptly halt crystallization. The samples were analysed using a transmission electron microscope (TEM), and the acquired images were processed using ImageJ to obtain crystal size distributions (CSDs). It was found that the enhanced mesomixing conditions resulted in smaller crystal sizes and narrower CSDs. This was because the nucleation rate was found to be mass-transfer-limited, such that higher mesomixing intensities promoted the nucleation rate from 6 × 1012 to 5 × 1013 m−3 s−1 and, therefore, favoured the formation of smaller crystals. In parallel, intensified mesomixing resulted in uniform distribution of the supersaturation and, hence, narrowed the CSDs.
Open AccessInvestigation on the Effect of Mesomixing on Crystal Quality during Antisolvent Crystallization of Nd2(SO4)3·8H2O
Rare earth elements (REEs) are essential for permanent magnets that are vital for wind turbines and electric vehicles motors (EV), and are also used in a range of high-tech devices such as smartphones, digital cameras, and electronic displays. Nickel metal hydride (NiMH) batteries have been identified as a potential source due to their short lifespans and an anticipated boom in the production of EV. The aim of this study was to investigate the effect of mesomixing on crystal quality in a non-confined impinging jet mixer (NCIJM) during antisolvent crystallization of 3.2 g/L Nd2(SO4)3 from a synthetic leach solution of NiMH battery using ethanol at an O/A ratio of 1.1. The jet streams were supplied at a Reynolds number (Re) between 7500 and 15,000. The product slurry was allowed to further crystallize in a stirred batch crystallizer at a Re of 13,000 for 45 s. An average yield of 90% was achieved. Laser diffraction and scanning electron microscopy (SEM) were used for size analysis. The initial results were inconclusive due to the secondary mixing effect in the stirred batch crystallizer. Therefore, the experiments were repeated, and samples were collected immediately after mixing in the NCIJM onto a porous grid placed on a high absorbance filter paper to abruptly halt crystallization. The samples were analysed using a transmission electron microscope (TEM), and the acquired images were processed using ImageJ to obtain crystal size distributions (CSDs). It was found that the enhanced mesomixing conditions resulted in smaller crystal sizes and narrower CSDs. This was because the nucleation rate was found to be mass-transfer-limited, such that higher mesomixing intensities promoted the nucleation rate from 6 × 1012 to 5 × 1013 m−3 s−1 and, therefore, favoured the formation of smaller crystals. In parallel, intensified mesomixing resulted in uniform distribution of the supersaturation and, hence, narrowed the CSDs.
- Open Access
Crystal Engineering in Antisolvent Crystallization of Rare Earth Elements (REEs)
Antisolvent crystallization is a separation technology that separates the solute from the solvent by the addition of another solvent, in which the solute is sparingly soluble. High yields are achieved by using higher antisolvent-to-aqueous ratios, but this generates higher supersaturation, which causes excessive nucleation. This results in the production of smaller particles, which are difficult to handle in downstream processes. In this work, the effect of varying the organic (antisolvent)-to-aqueous (O/A) ratio and seed loading on the yield, particle size distribution, and morphology of neodymium sulphate product, during its recovery from an aqueous leach solution using antisolvent crystallization, was investigated. A batch crystallizer was used for the experiments, while ethanol was used as an antisolvent. Neodymium sulphate octahydrate [Nd2(SO4)3.8H2O] seeds were used to investigate the effect of seed loading. It was found that particle sizes increased as the O/A ratio increased. This was attributed to the agglomeration of smaller particles that formed at high supersaturation. An O/A ratio of 1.4 resulted in higher yields and particles with a plate-like morphology. The increase in yield was attributed to the increased interaction of ethanol molecules with the solvent, which reduced the solubility of neodymium sulphate. Increasing the seed loading resulted in smaller particle sizes with narrow particle size distribution and improved filtration performance. This was attributed to the promotion of crystal growth and suppression of agglomeration in the presence of seeds.
Open AccessCrystal Engineering in Antisolvent Crystallization of Rare Earth Elements (REEs)
Antisolvent crystallization is a separation technology that separates the solute from the solvent by the addition of another solvent, in which the solute is sparingly soluble. High yields are achieved by using higher antisolvent-to-aqueous ratios, but this generates higher supersaturation, which causes excessive nucleation. This results in the production of smaller particles, which are difficult to handle in downstream processes. In this work, the effect of varying the organic (antisolvent)-to-aqueous (O/A) ratio and seed loading on the yield, particle size distribution, and morphology of neodymium sulphate product, during its recovery from an aqueous leach solution using antisolvent crystallization, was investigated. A batch crystallizer was used for the experiments, while ethanol was used as an antisolvent. Neodymium sulphate octahydrate [Nd2(SO4)3.8H2O] seeds were used to investigate the effect of seed loading. It was found that particle sizes increased as the O/A ratio increased. This was attributed to the agglomeration of smaller particles that formed at high supersaturation. An O/A ratio of 1.4 resulted in higher yields and particles with a plate-like morphology. The increase in yield was attributed to the increased interaction of ethanol molecules with the solvent, which reduced the solubility of neodymium sulphate. Increasing the seed loading resulted in smaller particle sizes with narrow particle size distribution and improved filtration performance. This was attributed to the promotion of crystal growth and suppression of agglomeration in the presence of seeds.
- Open Access
Effect of Heat Transfer Driving Force and Ice Seed Loading on the Production of Ice and Salt from a Dilute Brine Treated Using Eutectic Freeze Crystallization
Eutectic Freeze Crystallization (EFC) is a separation technology that separates solute from solvent by cooling the brine to a temperature below its eutectic point, such that ice and salt simultaneously crystallize out of the solution. Achieving consistent production of ice and salt at high production rates has been a challenge for EFC. This is due to heat transfer limitations, which are more severe when EFC is applied to dilute brines. This work investigated the effect of the heat transfer driving force, ΔTLMTD, and ice seed loading (SL) on the production of ice and salt from a dilute brine. A 1.45 L stirred crystallizer was used for the experiments at varying coolant temperatures to investigate the effect of ΔTLMTD, and at varying seed masses to investigate the effect of seed loading. It was found that, as the ΔTLMTD increased, the yield of ice and salt increased. This was attributed to the increase in the heat transfer rate as ΔTLMTD and heat transfer rate are directly related. The ice yield was divided between ice in suspension and ice formed on the wall (scale layer), with a majority of the total ice yield being scale ice. Increasing the seed loading (SL) increased the yield of ice in suspension and decreased the yield of scale ice. The seeds allowed for increased surface area for crystallization in the bulk. This allowed for most of the supersaturation to be consumed in the bulk, leaving little supersaturation for crystallization at the wall. This reduced the propensity for scale formation. The reduction in the scale layer increased the heat transfer rate between the bulk and the coolant, allowing for more ice to be formed in suspension.
Open AccessEffect of Heat Transfer Driving Force and Ice Seed Loading on the Production of Ice and Salt from a Dilute Brine Treated Using Eutectic Freeze Crystallization
Eutectic Freeze Crystallization (EFC) is a separation technology that separates solute from solvent by cooling the brine to a temperature below its eutectic point, such that ice and salt simultaneously crystallize out of the solution. Achieving consistent production of ice and salt at high production rates has been a challenge for EFC. This is due to heat transfer limitations, which are more severe when EFC is applied to dilute brines. This work investigated the effect of the heat transfer driving force, ΔTLMTD, and ice seed loading (SL) on the production of ice and salt from a dilute brine. A 1.45 L stirred crystallizer was used for the experiments at varying coolant temperatures to investigate the effect of ΔTLMTD, and at varying seed masses to investigate the effect of seed loading. It was found that, as the ΔTLMTD increased, the yield of ice and salt increased. This was attributed to the increase in the heat transfer rate as ΔTLMTD and heat transfer rate are directly related. The ice yield was divided between ice in suspension and ice formed on the wall (scale layer), with a majority of the total ice yield being scale ice. Increasing the seed loading (SL) increased the yield of ice in suspension and decreased the yield of scale ice. The seeds allowed for increased surface area for crystallization in the bulk. This allowed for most of the supersaturation to be consumed in the bulk, leaving little supersaturation for crystallization at the wall. This reduced the propensity for scale formation. The reduction in the scale layer increased the heat transfer rate between the bulk and the coolant, allowing for more ice to be formed in suspension.
- Open Access
Gypsum Seeding to Prevent Scaling
Eutectic freeze crystallization (EFC) is a novel separation technique that can be applied to treat brine solutions such as reverse osmosis retentates. These are often a mixture of different inorganic solutes. The treatment of calcium sulphate-rich brines using EFC often results in gypsum crystallization before any other species. This results in gypsum scaling on the cooled surfaces of the crystallizer, which is undesirable as it retards heat transfer rates and hence reduces the yield of other products. The aim of this study was to investigate and understand gypsum crystallization and gypsum scaling in the presence of gypsum seeds. Synthetic brine solutions were used in this research because they allowed an in-depth understanding of the gypsum bulk crystallization process and scaling tendency without the complexity of industrial brines. A cooled, U-shaped stainless-steel tube suspended in the saturated solution was employed as the scaling surface. This was because a tube-shaped surface enabled the introduction of a constant temperature cold surface in the saturated solution and most industrial EFC crystallizers are constructed from stainless steel. Gypsum seeding was effective in decreasing the mass of scale formed on the heat transfer surface. The most effective seed loading was 0.25 g/L, which reduced scale growth rate by 43%. Importantly, this seed loading is six times the theoretical critical seed loading. The seeding strategy also increased the gypsum crystallization kinetics in the bulk solution, which resulted in an increase in the mass of gypsum product. These findings are relevant for the operability and control of EFC processes, which suffer from scaling problems. By using an appropriate seeding strategy, two problems can be alleviated. Firstly, scaling on the heat transfer surface is minimised and, secondly, seeding increases the crystallization kinetics in the bulk solution, which is advantageous for product yield and recovery. It was also recommended that the use of silica as a seed material to prevent gypsum scaling should be investigated in future studies.
Open AccessGypsum Seeding to Prevent Scaling
Eutectic freeze crystallization (EFC) is a novel separation technique that can be applied to treat brine solutions such as reverse osmosis retentates. These are often a mixture of different inorganic solutes. The treatment of calcium sulphate-rich brines using EFC often results in gypsum crystallization before any other species. This results in gypsum scaling on the cooled surfaces of the crystallizer, which is undesirable as it retards heat transfer rates and hence reduces the yield of other products. The aim of this study was to investigate and understand gypsum crystallization and gypsum scaling in the presence of gypsum seeds. Synthetic brine solutions were used in this research because they allowed an in-depth understanding of the gypsum bulk crystallization process and scaling tendency without the complexity of industrial brines. A cooled, U-shaped stainless-steel tube suspended in the saturated solution was employed as the scaling surface. This was because a tube-shaped surface enabled the introduction of a constant temperature cold surface in the saturated solution and most industrial EFC crystallizers are constructed from stainless steel. Gypsum seeding was effective in decreasing the mass of scale formed on the heat transfer surface. The most effective seed loading was 0.25 g/L, which reduced scale growth rate by 43%. Importantly, this seed loading is six times the theoretical critical seed loading. The seeding strategy also increased the gypsum crystallization kinetics in the bulk solution, which resulted in an increase in the mass of gypsum product. These findings are relevant for the operability and control of EFC processes, which suffer from scaling problems. By using an appropriate seeding strategy, two problems can be alleviated. Firstly, scaling on the heat transfer surface is minimised and, secondly, seeding increases the crystallization kinetics in the bulk solution, which is advantageous for product yield and recovery. It was also recommended that the use of silica as a seed material to prevent gypsum scaling should be investigated in future studies.