ZRZh. M. Ramazanova

Zh. M. Ramazanova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zh. M. Ramazanova has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation of Intensive Wear Zones of an Oil Press Screw During Oilseed Processing

    by Gulnara Kokayeva, Mukhtarbek Kakimov, Zhanat Ramazanova, Maigul Mursalykova, Akerke Sarsenkyzy, Michał Bembenek

    The article presents a computational and experimental study of the wear of an oil press screw during the processing of oilseed raw materials. The study aimed to determine the most heavily loaded zones of the screw by comparing an engineering calculation model with experimental data. The calculation model included a linear pressure distribution along the screw, Coulomb’s law to estimate friction, and Archard’s equation to predict linear wear. Experimental verification was conducted by measuring changes in the geometric parameters of the screw flights across three screw zones after operation. The calculated annual wear in zones I, II, and III was 0.166, 0.243, and 0.318 mm/year, respectively, while the experimental values were 0.178, 0.260, and 0.348 mm/year, respectively. The deviation between the calculated and experimental data was within 7.2-9.4%, which confirms the applicability of the proposed model for preliminary wear assessment. It was established that the maximum wear is localized in zone III, corresponding to the final compression and material discharge section. The obtained results justify the need for local strengthening or the application of a wear-resistant coating to the most heavily loaded screw sections. From a practical standpoint, the proposed approach can be used in the reliability management system of an oil press to plan periodic inspections, identify priority maintenance areas, and select economically justified zones for screw restoration or strengthening.

  • ANALYSIS AND COMPARATIVE ASSESSMENT OF MACHINE PART RESTORATION METHODS

    by G. A. Kokayeva, Zh. M. Ramazanova, М. M. Mursalykova, A. Sarsenkyzy, M. Bembenek

    The restoration of worn machine parts is an important task in modern mechanical engineering. It contributes to increasing the reliability and durability of equipment, as well as reducing operating and repair costs. One of the effective ways to solve this problem is the use of wear-resistant protective coating technologies, which improve the performance characteristics of the working surfaces of machine parts. This paper presents an analytical review of scientific publications from the past 15 years devoted to the study of methods for producing wear-resistant protective coatings designed to withstand conditions of severe abrasive wear. The aim of this study is to systematize and summarize current scientific data on coating formation methods designed to improve the wear resistance and durability of machine parts. The methods under consideration are broadly classified into traditional, modern, and innovative categories. Traditional repair methods include machining, welding, and surfacing, which allow for the restoration of parts’ geometric dimensions and a partial improvement in their wear resistance. However, despite their widespread industrial use, these methods are characterized by significant labor and energy costs, and may also lead to changes in the structure and a reduction in the strength properties of the base material. In response to growing demands for the operational reliability and service life of machinery and equipment, modern, innovative surface hardening and restoration technologies are being actively developed, including plasma spraying, electro-spark alloying, ion-plasma methods, gas-thermal spraying, electric arc metallization, and other surface modification techniques. The use of these technologies enables the creation of coatings with improved physical, mechanical, and tribological properties, resulting in a significant increase in the wear resistance, corrosion resistance, and service life of machine parts. Keywords: wear-resistant coatings, surface modification, plasma spraying, electrical discharge alloying, arc spraying.

  • Open Access

    Modern composite armor materials

    by Zh.M. Ramazanova, G.A. Kokaeva, A.E. Zhakupova, O.K. Abdirashev

    Currently, composite armored vehicles based on a ceramic layer, polymer and natural fibers are of great interest. This work is a review article and includes scientific works over the past 18 years. The aim of the work is to generalize literary data on research on the creation of armored vehicles. Camamosetosite armor based on various brands of Kevlar is a promising material. At the same time, natural materials in their ballistic properties are not inferior to polymeric materials. Widespread use in this field of research and nanomaterials. The use of carbon nanotubes that differ in unique strength properties can significantly reduce the mass of body armor. When using nanomaterials for body armor can reduce its thickness by 15-35 times. Promising are also multilayer metal armored vehicles obtained by explosion welding by explosion. Light metals as aluminum and titanium are used as metal materials. As a result of heat treatment in the structure of composite material, intermetallic layers of TiAl3 with a thickness of 90-100 microns are formed. It is known that intermetallic compounds are characterized by high physical and mechanical properties. In this work, various composite materials are considered for anti-ocal resistance and resistance to high-speed impact.

  • Research of the parameters of a solar battery of composition materials for spacecraft

    by A. Zhakupova, Zh. Ramazanova, M. Zamalitdinova, M. Kovalenko, D. Turekhan

    Solar batteries are one of the most reliable, modern and well-tested options for providing spacecraft with energy. The growth of solar cell efficiency allows to increase the power capacity of the spacecraft (SC). In the course of the study, the main aim was achieved: a 3D model of a solar battery for a spacecraft was created in the SolidWorks program, a static analysis and modeling of the model in SolidWorks Simulation were carried out. The results obtained during the research make a certain contribution to the study of solar batteries, increasing the efficiency of their use in outer space. Modern methods for studying the parameters of a solar battery made of a composite material for spacecraft were used when performing the study.

  • Protective Properties of Coatings Obtained via Microarc Oxidation in Alkaline Electrolyte Solutions

    by Zh. M. Ramazanova, M. G. Zamalitdinova, K. Zh. Kirgizbayeva, A. U. Akhmedyanov, A. Y. Zhakupova

    The corrosion properties inherent in oxide coatings formed on VT1-0 and VT5 grade titanium alloys affected by fast pulsed discharges under the process of microarc oxidation (MAO) have been studied both after sealing the coatings with polymers and with no sealing. The MAO coatings were formed in a pulsed mode, the duration of the anode current pulse amounting to 250 ± 25 μs, the duration of cathode current pulse being of 5 ± 0.5 ms, the pause between the anode and cathode current pulses amounting to 250 ± 25 μs, and the repetition rate of the anode and cathode pulses being of 50 ± 0.5 Hz. Alkaline solutions were used as electrolytes. Fluoroplastic and epoxy resin solutions were used to seal the oxide coatings. The obtained MAO coatings had 4.4–7.5% porosity in the case of the VT1-0 grade alloy and 5.4–12.1% porosity in the case of the VT5 grade alloy. The average pore diameter in the oxide coatings ranged from 0.1 to 0.5 μm. The XRD phase analysis has shown the fact that, in the composition of oxide coatings, there are anatase and rutile modifications of titanium dioxide. The corrosion testing performed using a 24% sulfuric acid solution at 40 and 75°C has shown that both oxide and oxide-polymeric coatings formed on the VT1-0 grade alloy are more corrosion resistant than similar coatings formed on the VT5 grade alloy. All the types of coatings formed on the VT1-0 alloy are corrosion-resistant at a testing temperature of 40°C. The sealing of MAO coatings with the use of polymeric materials improves their corrosion-resistant properties.


  • Investigation of the properties of oxide coatings on titanium alloys obtained by plasma electrolytic oxidation

    by Zh. Ramazanova, M.G. Zamalitdinova, M.V. Kovalenko

    The use of structures made of titanium and its alloys, which have improved corrosion, physical and mechanical properties, are in demand in many industries. In this regard, the processes of modifying the surface of metals are of interest. One of the modern and promising methods of metal surface treatment is plasma electrolytic oxidation. Currently, there is a problem of widespread use of this process when DC modes are used in the implementation of the process. This is due to the large consumption of electricity. The purpose of this work is to study the morphological and corrosion properties of oxide coatings obtained in the pulsed anodecathode mode on titanium alloys VT1-0 and VT5 in various electrolyte solutions. Modification of the surface of titanium alloys was carried out at the duration of the anode current pulse of 250 ± 25 microseconds, the duration of the cathode current pulse of 5 ± 0.5 ms, the repetition frequency of the anode and cathode pulses of 50 ± 0.5 Hz. Alkaline solutions served as electrolytes. Oxide coatings obtained in various electrolytes are characterized by different porosity and coating thickness. Coatings with a finely porous structure, with an average pore diameter from 0.09 microns to 0.4 microns, and larger pore sizes of 0.6 – 0.7 microns were obtained. The porosity of the coatings ranges from 6.12% to 12.2%. According to the data of energy dispersion analysis, it was found that the structure of oxide coatings includes both components of the processed metal and components of the electrolyte solution. The main components, in this case, are oxygen and processed metal, as well as other elements such as boron, phosphorus, aluminium, fluorine, sodium, silicon and others. Corrosion tests according to GOST 9.308-85 under the influence of neutral salt mist at a temperature of (35 ± 2) °C with 1500 hours in the Ascott CC 450 chamber, it was shown that there was no corrosion damage to the coatings.