Akerke Sarsenkyzy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Akerke Sarsenkyzy has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Gulnara Kokayeva
Department of Technological Machinery and Equipment, S. Seifullin Kazakh Agro Technical Research University, Astana 010011, Kazakhstan
2 shared publications - Maigul Mursalykova
Shakarim University
2 shared publications - Michał Bembenek
AGH University of Krakow
2 shared publications - Zh. M. Ramazanova
L.N. Gumilyov Eurasian National University
2 shared publications - Mukhtarbek Kakimov
S. Seifullin Kazakh Agro Technical Research University
1 shared publication
Latest Publications
- Open Access
- 17 November 2026
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 34 (4) , 614-630
Investigation of Intensive Wear Zones of an Oil Press Screw During Oilseed Processing
The article presents a computational and experimental study of the wear of an oil press screw during the processing of oilseed raw materials. The study aimed to determine the most heavily loaded zones of the screw by comparing an engineering calculation model with experimental data. The calculation model included a linear pressure distribution along the screw, Coulomb’s law to estimate friction, and Archard’s equation to predict linear wear. Experimental verification was conducted by measuring changes in the geometric parameters of the screw flights across three screw zones after operation. The calculated annual wear in zones I, II, and III was 0.166, 0.243, and 0.318 mm/year, respectively, while the experimental values were 0.178, 0.260, and 0.348 mm/year, respectively. The deviation between the calculated and experimental data was within 7.2-9.4%, which confirms the applicability of the proposed model for preliminary wear assessment. It was established that the maximum wear is localized in zone III, corresponding to the final compression and material discharge section. The obtained results justify the need for local strengthening or the application of a wear-resistant coating to the most heavily loaded screw sections. From a practical standpoint, the proposed approach can be used in the reliability management system of an oil press to plan periodic inspections, identify priority maintenance areas, and select economically justified zones for screw restoration or strengthening.
- 17 November 2026
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 34 (4) , 614-630
Open AccessInvestigation of Intensive Wear Zones of an Oil Press Screw During Oilseed Processing
The article presents a computational and experimental study of the wear of an oil press screw during the processing of oilseed raw materials. The study aimed to determine the most heavily loaded zones of the screw by comparing an engineering calculation model with experimental data. The calculation model included a linear pressure distribution along the screw, Coulomb’s law to estimate friction, and Archard’s equation to predict linear wear. Experimental verification was conducted by measuring changes in the geometric parameters of the screw flights across three screw zones after operation. The calculated annual wear in zones I, II, and III was 0.166, 0.243, and 0.318 mm/year, respectively, while the experimental values were 0.178, 0.260, and 0.348 mm/year, respectively. The deviation between the calculated and experimental data was within 7.2-9.4%, which confirms the applicability of the proposed model for preliminary wear assessment. It was established that the maximum wear is localized in zone III, corresponding to the final compression and material discharge section. The obtained results justify the need for local strengthening or the application of a wear-resistant coating to the most heavily loaded screw sections. From a practical standpoint, the proposed approach can be used in the reliability management system of an oil press to plan periodic inspections, identify priority maintenance areas, and select economically justified zones for screw restoration or strengthening.
- 30 June 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 2, 2026,p. 137-151
ANALYSIS AND COMPARATIVE ASSESSMENT OF MACHINE PART RESTORATION METHODS
The restoration of worn machine parts is an important task in modern mechanical engineering. It contributes to increasing the reliability and durability of equipment, as well as reducing operating and repair costs. One of the effective ways to solve this problem is the use of wear-resistant protective coating technologies, which improve the performance characteristics of the working surfaces of machine parts. This paper presents an analytical review of scientific publications from the past 15 years devoted to the study of methods for producing wear-resistant protective coatings designed to withstand conditions of severe abrasive wear. The aim of this study is to systematize and summarize current scientific data on coating formation methods designed to improve the wear resistance and durability of machine parts. The methods under consideration are broadly classified into traditional, modern, and innovative categories. Traditional repair methods include machining, welding, and surfacing, which allow for the restoration of parts’ geometric dimensions and a partial improvement in their wear resistance. However, despite their widespread industrial use, these methods are characterized by significant labor and energy costs, and may also lead to changes in the structure and a reduction in the strength properties of the base material. In response to growing demands for the operational reliability and service life of machinery and equipment, modern, innovative surface hardening and restoration technologies are being actively developed, including plasma spraying, electro-spark alloying, ion-plasma methods, gas-thermal spraying, electric arc metallization, and other surface modification techniques. The use of these technologies enables the creation of coatings with improved physical, mechanical, and tribological properties, resulting in a significant increase in the wear resistance, corrosion resistance, and service life of machine parts. Keywords: wear-resistant coatings, surface modification, plasma spraying, electrical discharge alloying, arc spraying.
- 30 June 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 2, 2026,p. 137-151
ANALYSIS AND COMPARATIVE ASSESSMENT OF MACHINE PART RESTORATION METHODS
The restoration of worn machine parts is an important task in modern mechanical engineering. It contributes to increasing the reliability and durability of equipment, as well as reducing operating and repair costs. One of the effective ways to solve this problem is the use of wear-resistant protective coating technologies, which improve the performance characteristics of the working surfaces of machine parts. This paper presents an analytical review of scientific publications from the past 15 years devoted to the study of methods for producing wear-resistant protective coatings designed to withstand conditions of severe abrasive wear. The aim of this study is to systematize and summarize current scientific data on coating formation methods designed to improve the wear resistance and durability of machine parts. The methods under consideration are broadly classified into traditional, modern, and innovative categories. Traditional repair methods include machining, welding, and surfacing, which allow for the restoration of parts’ geometric dimensions and a partial improvement in their wear resistance. However, despite their widespread industrial use, these methods are characterized by significant labor and energy costs, and may also lead to changes in the structure and a reduction in the strength properties of the base material. In response to growing demands for the operational reliability and service life of machinery and equipment, modern, innovative surface hardening and restoration technologies are being actively developed, including plasma spraying, electro-spark alloying, ion-plasma methods, gas-thermal spraying, electric arc metallization, and other surface modification techniques. The use of these technologies enables the creation of coatings with improved physical, mechanical, and tribological properties, resulting in a significant increase in the wear resistance, corrosion resistance, and service life of machine parts. Keywords: wear-resistant coatings, surface modification, plasma spraying, electrical discharge alloying, arc spraying.