Dhruva Kumar Goyal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Dhruva Kumar Goyal has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Ravi Kant
Indian Institute of Technology Ropar
10 shared publications - Ramsingh Yadav
Department of Mechanical Engineering, Indian Institute of Technology Ropar, Rupnagar, India
3 shared publications - Arpit Bajpai1 shared publication
- Avneesh Kumar
Department of Mechanical Engineering, Indian Institute of Technology Ropar, Rupnagar 140001, India
1 shared publication Chitta Ranjan Tripathy
GNA University
1 shared publicationEkta Singla
1 shared publication
Latest Publications
- 13 July 2026
- Published by Elsevier in CIRP Journal of Manufacturing Science and Technology
- Vol. 69, 351-365
Thermal and microstructural analysis of laser remelting of cold-sprayed copper coating
- 13 July 2026
- Published by Elsevier in CIRP Journal of Manufacturing Science and Technology
- Vol. 69, 351-365
Thermal and microstructural analysis of laser remelting of cold-sprayed copper coating
- 13 September 2025
- Published by Elsevier in CIRP Journal of Manufacturing Science and Technology
- Vol. 63, 43-57
Influence of non-planar orientations on solidification microstructure during robot-assisted laser-wire directed energy deposition
- 13 September 2025
- Published by Elsevier in CIRP Journal of Manufacturing Science and Technology
- Vol. 63, 43-57
Influence of non-planar orientations on solidification microstructure during robot-assisted laser-wire directed energy deposition
- 8 April 2025
- Published by Elsevier in Materials Letters
- Vol. 392
Influence of clamp pressure on weld performance and fracture mode in laser welded polyamide-6 sheets
- 8 April 2025
- Published by Elsevier in Materials Letters
- Vol. 392
Influence of clamp pressure on weld performance and fracture mode in laser welded polyamide-6 sheets
- 28 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3371-3379
Experimental study of rectangular-curved magnet–based magnetorheological finishing tool for copper cylindrical workpiece
A mechanical product with a finely finished surface and accuracy is a great requirement of current industries and individuals because of its enhanced operational life, reliability, smooth interchangeability, and aesthetic appealing features. Therefore, fine-finishing processes are of extensive importance these days. The magnetorheological (MR) finishing processes are developed where the finishing forces provide uniform forces to a magnetorheological polishing fluid which in turn produces a supergrade finishing. In this study, the rectangular-curved magnet–based MR finishing process was used to superfinish the exterior surface of the cylindrical workpiece of copper material (which is typically used as an electron discharge machine electrode). To ensure the functionality of the current tool, the magnetic simulation was also performed to analyze the magnetic flux distribution within the tool structure, working gap, and workpiece surface. The synthesized MR polishing fluid was applied on the finishing surface of rectangular-curved magnets which further maintained a working gap of 1 mm during the experimentation. The results concluded that the overall 74% roughness change with rectangular-curved magnets (i.e., from initial Ra as 251 nm to final Ra as 66 nm was observed using rotational speed of workpiece as 500 rpm, tool feed as 50 mm/min and 45 min of finishing time), which was more efficient than the existing results of circular-type magnets. Also, the significant improvement in surface texture from the initial to the final finished copper workpiece was confirmed through the scanning electron microscopic images.
- 28 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3371-3379
Experimental study of rectangular-curved magnet–based magnetorheological finishing tool for copper cylindrical workpiece
A mechanical product with a finely finished surface and accuracy is a great requirement of current industries and individuals because of its enhanced operational life, reliability, smooth interchangeability, and aesthetic appealing features. Therefore, fine-finishing processes are of extensive importance these days. The magnetorheological (MR) finishing processes are developed where the finishing forces provide uniform forces to a magnetorheological polishing fluid which in turn produces a supergrade finishing. In this study, the rectangular-curved magnet–based MR finishing process was used to superfinish the exterior surface of the cylindrical workpiece of copper material (which is typically used as an electron discharge machine electrode). To ensure the functionality of the current tool, the magnetic simulation was also performed to analyze the magnetic flux distribution within the tool structure, working gap, and workpiece surface. The synthesized MR polishing fluid was applied on the finishing surface of rectangular-curved magnets which further maintained a working gap of 1 mm during the experimentation. The results concluded that the overall 74% roughness change with rectangular-curved magnets (i.e., from initial Ra as 251 nm to final Ra as 66 nm was observed using rotational speed of workpiece as 500 rpm, tool feed as 50 mm/min and 45 min of finishing time), which was more efficient than the existing results of circular-type magnets. Also, the significant improvement in surface texture from the initial to the final finished copper workpiece was confirmed through the scanning electron microscopic images.
- 9 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Laser heat conduction joining of polycarbonate and aluminum alloy
The present work demonstrates the laser heat conduction joining (LHCJ) of polycarbonate and aluminum alloy. The experiments are performed to examine the impact of scan speed and laser power on the joint’s strength and quality. The bonding between the substrates was assessed by examining the cross-section using a scanning electron microscope and conducting energy-dispersive X-ray spectroscopy. The fractured surfaces are inspected by an optical microscope to explore the bond morphology. A finite-element-based numerical model is developed for the estimation of interface temperature and validated with the experimental results. Results of lap shear tests show that the weld strength is significantly affected by the laser power, scan speed, interface temperature, and bubble area. Microscopic observations of the joint interface disclose bubble area and mechanical interlocking between polycarbonate and aluminum. Through X-ray photoelectron spectroscopy (XPS) analysis, it was discovered that the interface experiences chemical bonding facilitated by the formation of Al-O-C bonds, which effectively enhances the strength of the joint.
- 9 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Laser heat conduction joining of polycarbonate and aluminum alloy
The present work demonstrates the laser heat conduction joining (LHCJ) of polycarbonate and aluminum alloy. The experiments are performed to examine the impact of scan speed and laser power on the joint’s strength and quality. The bonding between the substrates was assessed by examining the cross-section using a scanning electron microscope and conducting energy-dispersive X-ray spectroscopy. The fractured surfaces are inspected by an optical microscope to explore the bond morphology. A finite-element-based numerical model is developed for the estimation of interface temperature and validated with the experimental results. Results of lap shear tests show that the weld strength is significantly affected by the laser power, scan speed, interface temperature, and bubble area. Microscopic observations of the joint interface disclose bubble area and mechanical interlocking between polycarbonate and aluminum. Through X-ray photoelectron spectroscopy (XPS) analysis, it was discovered that the interface experiences chemical bonding facilitated by the formation of Al-O-C bonds, which effectively enhances the strength of the joint.
- 16 June 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 179
Experimental and numerical study of underwater laser transmission welding
- 16 June 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 179
Experimental and numerical study of underwater laser transmission welding
- 9 January 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 38 (4) , 485-493
Mechanism of bonding during laser transmission welding using EIP absorber
This paper aims to investigate the bonding mechanism during laser transmission welding of polycarbonate sheets using an electrolytic iron powder (EIP) absorber. The experiments are performed at different scan speeds and laser powers. The mechanical strength is determined by the lap shear test. The influence of line energy, interface temperature, and absorptivity on weld strength is discussed. The weld characteristics, bond morphology, and elemental distribution at the cross-section and fracture interface of the welded samples are analyzed. The results show that the maximum breaking strength of 1180 N is obtained at the 400 mm/min scan speed and 100 W laser power. The iron particles are observed mechanically interlocked at the lowest line energy with partial chemical bonding. However, the chain diffusion and chemical bonding have been increased with line energy. Thermal degradation and burning of the polycarbonate at the interface restrict the bonding and reduces the weld strength.
- 9 January 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 38 (4) , 485-493
Mechanism of bonding during laser transmission welding using EIP absorber
This paper aims to investigate the bonding mechanism during laser transmission welding of polycarbonate sheets using an electrolytic iron powder (EIP) absorber. The experiments are performed at different scan speeds and laser powers. The mechanical strength is determined by the lap shear test. The influence of line energy, interface temperature, and absorptivity on weld strength is discussed. The weld characteristics, bond morphology, and elemental distribution at the cross-section and fracture interface of the welded samples are analyzed. The results show that the maximum breaking strength of 1180 N is obtained at the 400 mm/min scan speed and 100 W laser power. The iron particles are observed mechanically interlocked at the lowest line energy with partial chemical bonding. However, the chain diffusion and chemical bonding have been increased with line energy. Thermal degradation and burning of the polycarbonate at the interface restrict the bonding and reduces the weld strength.
- 28 July 2022
- Published by Taylor & Francis in Journal of Thermal Stresses
- Vol. 45 (8) , 617-629
Enhancing process competency by forced cooling in laser bending process
Laser bending utilizes laser-induced thermal distortion to bend the sheet metal. This process is advantageous for job and batch productions but not suitable for mass production due to small bend angle per scan. This study aims to increase the bend angle per scan by applying forced cooling at the surface opposite to the laser scan. A 3-D numerical model is developed for laser bending process to analyze the effect of forced cooling on bend angle and edge effect. Results show that the bend angle can be significantly increased by applying forced cooling on the surface opposite the laser scan. However, the application of forced cooling is found to be effective only at high line energy, but it affects adversely at low line energy. Results also show that the edge effect is increased by the application of forced cooling at high line energy; however, it is marginally affected at low line energy.
- 28 July 2022
- Published by Taylor & Francis in Journal of Thermal Stresses
- Vol. 45 (8) , 617-629
Enhancing process competency by forced cooling in laser bending process
Laser bending utilizes laser-induced thermal distortion to bend the sheet metal. This process is advantageous for job and batch productions but not suitable for mass production due to small bend angle per scan. This study aims to increase the bend angle per scan by applying forced cooling at the surface opposite to the laser scan. A 3-D numerical model is developed for laser bending process to analyze the effect of forced cooling on bend angle and edge effect. Results show that the bend angle can be significantly increased by applying forced cooling on the surface opposite the laser scan. However, the application of forced cooling is found to be effective only at high line energy, but it affects adversely at low line energy. Results also show that the edge effect is increased by the application of forced cooling at high line energy; however, it is marginally affected at low line energy.
- Open Access
Enhancing Corrosion Performance of Cold-Sprayed Titanium/Baghdadite (Ti/BAG) Bio-Composite Coatings via Laser Treatment
This study aims to enhance the corrosion performance of cold-sprayed titanium/baghdadite (Ti/BAG) bio-composite coatings. Laser post processing was performed to reduce porosity and improve mechanical properties. The process parameters for laser treatment of cold-sprayed coatings were verified experimentally using scanning electron microscopy (SEM) and a thermal imaging camera. The laser-treated coatings are analyzed with SEM, energy-dispersive spectroscopy (EDS), ImageJ software, and X-ray diffraction (XRD). Furthermore, electrochemical analysis of the laser-treated and as-sprayed coatings was conducted in Ringer’s solution. The results of this study revealed that laser treatment helps significantly in enhancing resistance to corrosion for Ti/BAG composite coatings in a Ringer’s solution. The reduction in porosity and surface roughness is ascribed as the reason for their superior performance relative to as-sprayed coatings.
Open AccessEnhancing Corrosion Performance of Cold-Sprayed Titanium/Baghdadite (Ti/BAG) Bio-Composite Coatings via Laser Treatment
This study aims to enhance the corrosion performance of cold-sprayed titanium/baghdadite (Ti/BAG) bio-composite coatings. Laser post processing was performed to reduce porosity and improve mechanical properties. The process parameters for laser treatment of cold-sprayed coatings were verified experimentally using scanning electron microscopy (SEM) and a thermal imaging camera. The laser-treated coatings are analyzed with SEM, energy-dispersive spectroscopy (EDS), ImageJ software, and X-ray diffraction (XRD). Furthermore, electrochemical analysis of the laser-treated and as-sprayed coatings was conducted in Ringer’s solution. The results of this study revealed that laser treatment helps significantly in enhancing resistance to corrosion for Ti/BAG composite coatings in a Ringer’s solution. The reduction in porosity and surface roughness is ascribed as the reason for their superior performance relative to as-sprayed coatings.
- 25 June 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (5-6) , 3771-3786
An integrated hybrid methodology for estimation of absorptivity and interface temperature in laser transmission welding
- 25 June 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (5-6) , 3771-3786
An integrated hybrid methodology for estimation of absorptivity and interface temperature in laser transmission welding