Wahid Luthfi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Wahid Luthfi has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Surian Pinem
National Research and Innovation Agency
7 shared publications - Donny Hartanto
ORNL
4 shared publications - Peng Hong Liem
Cooperative Major in Nuclear Energy, Graduate School of Engineering, Tokyo City University, 1-28-1 Tamazutsumi, Setagaya, Tokyo 158-8557, Japan
3 shared publications - Muhammad Darwis Isnaini
National Research and Innovation Agency
2 shared publications - Tukiran Surbakti
National Research and Innovation Agency (BRIN)
2 shared publications - Zuhair Zuhair
Research Center for Nuclear Reactor Technology, Research Organization for Nuclear Energy, National Research and Innovation Agency of Indonesia, Kawasan Sains dan Teknologi, B.J. Habibie Office Building No.80, Serpong, Tangerang Selatan Indonesia 15310
2 shared publications
Latest Publications
- Open Access
- 1 July 2026
- Published by KEAI Publishing in International Journal of Advanced Nuclear Reactor Design and Technology
- Vol. 8 (3) , 311-323
Enhancing the Efficiency of Mo-99 Production in an IAEA 10 MW Research Reactor Through OpenMC-Based Neutron Transport Modeling
- 1 July 2026
- Published by KEAI Publishing in International Journal of Advanced Nuclear Reactor Design and Technology
- Vol. 8 (3) , 311-323
Open AccessEnhancing the Efficiency of Mo-99 Production in an IAEA 10 MW Research Reactor Through OpenMC-Based Neutron Transport Modeling
- Open Access
- 1 September 2025
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 38 (3) , 1431-1447
Comparison of Neutronic and Thermal-Hydraulic Performance of KOMODO, NODAL3, and COBRA for Steady-State Operation of APR1400
The important challenge in preparing nuclear reactor safety parameters is in the coupled neutronic and thermohydraulic calculation since the thermohydraulic parameters of the coolant could affect the neutron flux and power distribution. For this reason, it is necessary to carry out accurate calculations for these two parameters. KOMODO is one of the open-source coupled neutronic and thermal-hydraulic (N/TH) calculation codes, while NODAL3 is an in-house coupled N/TH code owned by BRIN. On the other hand, COBRA-EN has also been widely used for steady-state thermohydraulic calculations and could be used to compare the thermal hydraulics solver performance. The APR1400 reactor core was selected under steady-state conditions, either hot zero power (HZP) or critical hot full power (HFP). The calculated core multiplication factor of our HZP model to the reference data is 100 pcm. The radial and axial power distribution calculated by KOMODO and NODAL3 agree with a maximum of 4.78% difference. For steady-state thermal-hydraulics calculations, there was a difference of 1.84% at maximum between KOMODO and COBRA-EN. The KOMODO, NODAL3, and COBRA-EN codes show consistent neutronic and thermohydraulic performance on the APR1400 steady-state calculation model.
- 1 September 2025
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 38 (3) , 1431-1447
Open AccessComparison of Neutronic and Thermal-Hydraulic Performance of KOMODO, NODAL3, and COBRA for Steady-State Operation of APR1400
The important challenge in preparing nuclear reactor safety parameters is in the coupled neutronic and thermohydraulic calculation since the thermohydraulic parameters of the coolant could affect the neutron flux and power distribution. For this reason, it is necessary to carry out accurate calculations for these two parameters. KOMODO is one of the open-source coupled neutronic and thermal-hydraulic (N/TH) calculation codes, while NODAL3 is an in-house coupled N/TH code owned by BRIN. On the other hand, COBRA-EN has also been widely used for steady-state thermohydraulic calculations and could be used to compare the thermal hydraulics solver performance. The APR1400 reactor core was selected under steady-state conditions, either hot zero power (HZP) or critical hot full power (HFP). The calculated core multiplication factor of our HZP model to the reference data is 100 pcm. The radial and axial power distribution calculated by KOMODO and NODAL3 agree with a maximum of 4.78% difference. For steady-state thermal-hydraulics calculations, there was a difference of 1.84% at maximum between KOMODO and COBRA-EN. The KOMODO, NODAL3, and COBRA-EN codes show consistent neutronic and thermohydraulic performance on the APR1400 steady-state calculation model.
- Open Access
- 30 March 2025
- Published by University of Baghdad College of Science in Iraqi Journal of Science
- p. 1071-1079
Radiation Shielding Optimization of ADS-SAMOP Reactor Test Facility
The accelerator driven system subcritical reactor assembly for Molybdenum-99 or 99Mo isotope production (ADS-SAMOP) reactor test facility is located at the Kartini research reactor complex. The direct exposure at the ADS-SAMOP reactor facility system can reach 1600 mSv/h at a distance of 1 meter from the center of the reactor core. The minimum ordinary concrete shielding required in the radial direction is 2 m thickness with 3-meter height to qualify the maximum dose for radiation workers of 7 μSv/h. The aim of this study is to improve shielding configuration to achieve safety requirements. The method used is a calculation using computer code based on Monte Carlo. The results show that, by using barite concrete with 3 m in height, the thickness of radiation shielding at radial direction of ADS-SAMOP facility can achieve an optimum of only 1.5 m. The analysis results also concluded that the additional radiation shielding to the top of reactor tank must be added if the radial shielding is ordinary concrete.
- 30 March 2025
- Published by University of Baghdad College of Science in Iraqi Journal of Science
- p. 1071-1079
Open AccessRadiation Shielding Optimization of ADS-SAMOP Reactor Test Facility
The accelerator driven system subcritical reactor assembly for Molybdenum-99 or 99Mo isotope production (ADS-SAMOP) reactor test facility is located at the Kartini research reactor complex. The direct exposure at the ADS-SAMOP reactor facility system can reach 1600 mSv/h at a distance of 1 meter from the center of the reactor core. The minimum ordinary concrete shielding required in the radial direction is 2 m thickness with 3-meter height to qualify the maximum dose for radiation workers of 7 μSv/h. The aim of this study is to improve shielding configuration to achieve safety requirements. The method used is a calculation using computer code based on Monte Carlo. The results show that, by using barite concrete with 3 m in height, the thickness of radiation shielding at radial direction of ADS-SAMOP facility can achieve an optimum of only 1.5 m. The analysis results also concluded that the additional radiation shielding to the top of reactor tank must be added if the radial shielding is ordinary concrete.
- Open Access
- 2 December 2024
- Published by National Research and Innovation Agency in Atom Indonesia
- Vol. 51 (1) , 71-80
Preliminary Neutronic Studies on RSG-GAS Fuel Element with 4.8 grU/cc and Burnable Poison Wire for Reactivity Reduction
High-density fuel can increase the operating cycle of a nuclear reactor. The G.A. Siwabessy Multipurpose Reactor (RSG-GAS) is a research reactor owned by Indonesia that currently uses 19.75 % enriched uranium silicide fuel (U3Si2-Al) with a uranium density of 2.965 grU/cc. Previous studies have shown that high-density fuel, 4.8 grU/cc, can be used in the RSG-GAS core to extend the operating cycle. Previous studies related to high-density fuel conversion scenarios included a temporary conversion process to a density of 3.55 grU/cc before being increased to 4.8 grU/cc. However, the previous conversion process requires the addition of control rods to suppress the excess reactivity of the RSG-GAS. The current study focuses on determining the configuration of burnable poison wire for the standard fuel element of RSG-GAS (FE) made of cadmium and hafnium to suppress the reactivity (k-inf) of the 4.8 grU/cc fuel element so it could have an initial reactivity closer to the 2.965 grU/cc fuel. 5 pairs of 0.4 mm diameter Cd-wire coated with 0.1 mm AlMg2 cladding can suppress the reactivity of the fuel assembly, while 7 pairs of 0.8 mm diameter Hf-wire without cladding could suppress reactivity longer. The temperature coefficient of reactivity for the moderator temperature (MTC) and fuel temperature (FTC) also becomes more negative in high-density FE RSG-GAS while the amount of Pu-239 produced increases in high-density fuel element.
- 2 December 2024
- Published by National Research and Innovation Agency in Atom Indonesia
- Vol. 51 (1) , 71-80
Open AccessPreliminary Neutronic Studies on RSG-GAS Fuel Element with 4.8 grU/cc and Burnable Poison Wire for Reactivity Reduction
High-density fuel can increase the operating cycle of a nuclear reactor. The G.A. Siwabessy Multipurpose Reactor (RSG-GAS) is a research reactor owned by Indonesia that currently uses 19.75 % enriched uranium silicide fuel (U3Si2-Al) with a uranium density of 2.965 grU/cc. Previous studies have shown that high-density fuel, 4.8 grU/cc, can be used in the RSG-GAS core to extend the operating cycle. Previous studies related to high-density fuel conversion scenarios included a temporary conversion process to a density of 3.55 grU/cc before being increased to 4.8 grU/cc. However, the previous conversion process requires the addition of control rods to suppress the excess reactivity of the RSG-GAS. The current study focuses on determining the configuration of burnable poison wire for the standard fuel element of RSG-GAS (FE) made of cadmium and hafnium to suppress the reactivity (k-inf) of the 4.8 grU/cc fuel element so it could have an initial reactivity closer to the 2.965 grU/cc fuel. 5 pairs of 0.4 mm diameter Cd-wire coated with 0.1 mm AlMg2 cladding can suppress the reactivity of the fuel assembly, while 7 pairs of 0.8 mm diameter Hf-wire without cladding could suppress reactivity longer. The temperature coefficient of reactivity for the moderator temperature (MTC) and fuel temperature (FTC) also becomes more negative in high-density FE RSG-GAS while the amount of Pu-239 produced increases in high-density fuel element.
- Open Access
- 1 December 2024
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 37 (4) , 2012-2023
Neutronic Analysis of the AP1000 Fuel Assembly with Accident Tolerant Cladding Materials
An alternative material for fuel cladding was required to prevent oxidation caused by interacting with steam, leading to improvement in core integrity. This study analyzes reactor physics parameters of various cladding material candidates for Pressurized Water Reactor (PWR) such as SS-304 austenitic stainless steel, FeCrAl alloy, APMT alloy, and silicon carbide (SiC) ceramic, as candidate Accident Tolerant Fuel (ATF). The neutronic parameters such as infinite multiplication factor (k-inf), and neutron spectrum, while temperature reactivity coefficient related to fuel temperature (DTC) and moderator temperature (MTC) is also considered, followed by a void coefficient of reactivity (VCR) of each candidate material were then compared with ZIRLO as a standard cladding material of AP1000. k-inf calculated by SRAC2006 is also compared to MCNP for various fuel assembly types. At the beginning of cycle (BOC), the 2.35% UO2 using SiC gives a higher kinf than ZIRLO at 937 pcm, while 4.45% UO2 with 88 IFBA & 9 PYREX at 796 pcm. FeCrAl, APMT, and SS-304 cladding gave a smaller k-inf compared to ZIRLO in the range of 11000-14000 pcm at 2.35% UO2 fuel assembly. The values of DTC, MTC, and VCR were still negative throughout the reactor operation which indicates that the inherent safety feature of alternative cladding was possible for this type of fuel assembly, especially for iron-based cladding material followed by an increase in fuel enrichment.
- 1 December 2024
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 37 (4) , 2012-2023
Open AccessNeutronic Analysis of the AP1000 Fuel Assembly with Accident Tolerant Cladding Materials
An alternative material for fuel cladding was required to prevent oxidation caused by interacting with steam, leading to improvement in core integrity. This study analyzes reactor physics parameters of various cladding material candidates for Pressurized Water Reactor (PWR) such as SS-304 austenitic stainless steel, FeCrAl alloy, APMT alloy, and silicon carbide (SiC) ceramic, as candidate Accident Tolerant Fuel (ATF). The neutronic parameters such as infinite multiplication factor (k-inf), and neutron spectrum, while temperature reactivity coefficient related to fuel temperature (DTC) and moderator temperature (MTC) is also considered, followed by a void coefficient of reactivity (VCR) of each candidate material were then compared with ZIRLO as a standard cladding material of AP1000. k-inf calculated by SRAC2006 is also compared to MCNP for various fuel assembly types. At the beginning of cycle (BOC), the 2.35% UO2 using SiC gives a higher kinf than ZIRLO at 937 pcm, while 4.45% UO2 with 88 IFBA & 9 PYREX at 796 pcm. FeCrAl, APMT, and SS-304 cladding gave a smaller k-inf compared to ZIRLO in the range of 11000-14000 pcm at 2.35% UO2 fuel assembly. The values of DTC, MTC, and VCR were still negative throughout the reactor operation which indicates that the inherent safety feature of alternative cladding was possible for this type of fuel assembly, especially for iron-based cladding material followed by an increase in fuel enrichment.
- 28 March 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 422
Study on neutronic behavior of VVER-1000 fuel assembly with duplex fuel rod design
- 28 March 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 422
Study on neutronic behavior of VVER-1000 fuel assembly with duplex fuel rod design
- 22 January 2024
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 198 (10) , 1935-1949
Evaluation of Kinetic Parameters RSG-GAS Reactor Equilibrium Silicide Core Using Continuous-Energy Monte Carlo Serpent 2 Code
- 22 January 2024
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 198 (10) , 1935-1949
Evaluation of Kinetic Parameters RSG-GAS Reactor Equilibrium Silicide Core Using Continuous-Energy Monte Carlo Serpent 2 Code
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Nuclear Technology and Radiation Protection
- Vol. 39 (1) , 12-20
The effect of burnable absorbers on criticality and reactivity coefficient of VVER-1000 assembly
Burnable absorbers play an important role in nuclear reactor safety and exploring their effect on the reactor core behavior is an important issue in the design and operation of the reactor core. The aim of the present work was to discover the effect of burnable absorbers on criticality and reactivity coefficient of VVER-1000 assembly. The calculations were conducted with a 3-D Monte Carlo transport code MCNP6 and ENDF/B-VII.1 nuclear library. The Gd2O3 content varying from 0 wt.% to 8 wt.% was considered to complete the inter-comparison analysis between the criticality and the reactivity coefficients for three UO2+Gd2O3 fuel configurations. At the beginning of the cycle, there is a significant difference between the criticality (kinf) of assembly with and without Gd2O3, however, at the middle of the cycle those differences become very small and almost the same at the end of the cycle. The Doppler temperature coefficient values are always sufficiently negative and demonstrate a more negative trend with increasing gadolinium concentrations and fuel burnup. At beginning of the cycle, the moderator temperature coefficient value increases negatively as gadolinium concentration increases but, at middle of the cycle this trend does not occur. The fuel composition is predicted to be the reason behind this situation. At the end of cycle, there is no clear trend in the moderator temperature coefficient values with respect to Gd2O3 concentration. The absorbing effect of Gd2O3 appears to have diminished significantly. Overall, this research provides insights into the influence of the burnable absorbers on the neutronic parameters of the VVER-1000 assembly and its contribution to reactor safety.
- 1 January 2024
- Published by National Library of Serbia in Nuclear Technology and Radiation Protection
- Vol. 39 (1) , 12-20
Open AccessThe effect of burnable absorbers on criticality and reactivity coefficient of VVER-1000 assembly
Burnable absorbers play an important role in nuclear reactor safety and exploring their effect on the reactor core behavior is an important issue in the design and operation of the reactor core. The aim of the present work was to discover the effect of burnable absorbers on criticality and reactivity coefficient of VVER-1000 assembly. The calculations were conducted with a 3-D Monte Carlo transport code MCNP6 and ENDF/B-VII.1 nuclear library. The Gd2O3 content varying from 0 wt.% to 8 wt.% was considered to complete the inter-comparison analysis between the criticality and the reactivity coefficients for three UO2+Gd2O3 fuel configurations. At the beginning of the cycle, there is a significant difference between the criticality (kinf) of assembly with and without Gd2O3, however, at the middle of the cycle those differences become very small and almost the same at the end of the cycle. The Doppler temperature coefficient values are always sufficiently negative and demonstrate a more negative trend with increasing gadolinium concentrations and fuel burnup. At beginning of the cycle, the moderator temperature coefficient value increases negatively as gadolinium concentration increases but, at middle of the cycle this trend does not occur. The fuel composition is predicted to be the reason behind this situation. At the end of cycle, there is no clear trend in the moderator temperature coefficient values with respect to Gd2O3 concentration. The absorbing effect of Gd2O3 appears to have diminished significantly. Overall, this research provides insights into the influence of the burnable absorbers on the neutronic parameters of the VVER-1000 assembly and its contribution to reactor safety.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2967 (1) , 200001
Evaluation of environmental radiation monitoring in nuclear Serpong facility area
Monitoring of environmental radiation due to the presence and operation of nuclear facilities in a certain area is an absolute requirement that must be fulfille
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2967 (1) , 200001
Open AccessEvaluation of environmental radiation monitoring in nuclear Serpong facility area
Monitoring of environmental radiation due to the presence and operation of nuclear facilities in a certain area is an absolute requirement that must be fulfille
- Open Access
- 5 September 2023
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 63 (4) , 242–249
Effect of cross-sections data on calculated static neutronic parameters of PWR MOX/UO2 core transient benchmark case using NODAL3 code
This paper describes the effect of cross-section data generated by several codes on calculated neutronic parameters. The Pressurized Water Reactor Mixed Oxide and Uranium Oxide (PWR MOX/UO2) Core Transient Benchmark case was chosen because it has been used widely to validate neutronic codes. The cross-section data in this study will be generated by SRAC, Serpent, and HELIOS codes. The NODAL3 code will be used to calculate neutronic parameters from each cross-section. The neutronic parameters calculated by NODAL3 are the effective multiplication factor (keff), control rod worth, critical boron concentration, and power distribution under Hot Zero Power (HZP) conditions. The Power-Weighted Error (PWE) and Error-Weighted Error (EWE), as a measure of the relative error in fuel assembly power, are less than 5 %, indicating that the calculation is consistent with DeCART as a reference. The difference in calculated radial power peaking factor for all three cross-sections to reference data reaches 6.284 % (G-3), 8.438 % (G-3), and 10.998 % (C-7), respectively, for SRAC, Serpent, and HELIOS. The axial power distribution calculated by NODAL3 at the top and bottom of the reactor core has a relative error that peaked at 16.60 %, 13.86 %, and 10.20 %, respectively, for cross-sections provided by SRAC, Serpent, and HELIOS. Further improvements are needed for NODAL3 by applying various discontinuity factors to improve its performance.
- 5 September 2023
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 63 (4) , 242–249
Open AccessEffect of cross-sections data on calculated static neutronic parameters of PWR MOX/UO2 core transient benchmark case using NODAL3 code
This paper describes the effect of cross-section data generated by several codes on calculated neutronic parameters. The Pressurized Water Reactor Mixed Oxide and Uranium Oxide (PWR MOX/UO2) Core Transient Benchmark case was chosen because it has been used widely to validate neutronic codes. The cross-section data in this study will be generated by SRAC, Serpent, and HELIOS codes. The NODAL3 code will be used to calculate neutronic parameters from each cross-section. The neutronic parameters calculated by NODAL3 are the effective multiplication factor (keff), control rod worth, critical boron concentration, and power distribution under Hot Zero Power (HZP) conditions. The Power-Weighted Error (PWE) and Error-Weighted Error (EWE), as a measure of the relative error in fuel assembly power, are less than 5 %, indicating that the calculation is consistent with DeCART as a reference. The difference in calculated radial power peaking factor for all three cross-sections to reference data reaches 6.284 % (G-3), 8.438 % (G-3), and 10.998 % (C-7), respectively, for SRAC, Serpent, and HELIOS. The axial power distribution calculated by NODAL3 at the top and bottom of the reactor core has a relative error that peaked at 16.60 %, 13.86 %, and 10.20 %, respectively, for cross-sections provided by SRAC, Serpent, and HELIOS. Further improvements are needed for NODAL3 by applying various discontinuity factors to improve its performance.