Vijay Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vijay Kumar has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Rahul Chhibber
MED, IIT Jodhpur, Rajasthan, India
5 shared publications - Lochan Sharma
UCRD, Chandigarh University
4 shared publications Rahul Chhibber
Indian Institute of Technology Jodhpur
4 shared publications- Jagdish Kumar
Department of Mechanical Engineering, Indian Institute of Technology Jodhpur, Karwar, India
2 shared publications - Sumit Mahajan
Department of Mechanical Engineering & Design Jaypee Institute of Information Technology Noida UP India
1 shared publication - Waris Nawaz Khan
Department of Mechanical Engineering, Indian Institute of Technology Jodhpur, Jodhpur, India
1 shared publication
Latest Publications
- 28 March 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 240 (3) , 343-355
High-temperature corrosion behaviour of IN617 and AISI 304H alloys in mixed salt environment at 750 °C for power plant applications
This study examines the hot corrosion behavior of Alloy 617 and AISI 304H under mixed salt environments at 750 °C, relevant to their use in reheater, superheater, and steam header tubing in advanced ultra-supercritical boilers. A 100-h cyclic hot corrosion test was conducted using 3–5 mg/cm² salt mixtures (75% Na 2 SO 4 + 25% NaCl and 75% Na 2 SO 4 + 20% NaCl + 5% V 2 O 5 ). Corrosion kinetics were monitored through weight gain measurements, while SEM/EDS and X-ray diffraction (XRD) analyzed surface and cross-section morphology. Results showed IN617 exhibited better resistance in the Salt 1 environment, whereas SS304H performed better in Salt 2, as indicated by lower weight gain and parabolic rate constants. Higher chlorine and vanadium content accelerated corrosion, promoting cracks and voids from molten chlorides. Oxide scales formed at high temperatures were enriched with Ni, Cr, Fe, and O, alongside other reactive species.
- 28 March 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 240 (3) , 343-355
High-temperature corrosion behaviour of IN617 and AISI 304H alloys in mixed salt environment at 750 °C for power plant applications
This study examines the hot corrosion behavior of Alloy 617 and AISI 304H under mixed salt environments at 750 °C, relevant to their use in reheater, superheater, and steam header tubing in advanced ultra-supercritical boilers. A 100-h cyclic hot corrosion test was conducted using 3–5 mg/cm² salt mixtures (75% Na 2 SO 4 + 25% NaCl and 75% Na 2 SO 4 + 20% NaCl + 5% V 2 O 5 ). Corrosion kinetics were monitored through weight gain measurements, while SEM/EDS and X-ray diffraction (XRD) analyzed surface and cross-section morphology. Results showed IN617 exhibited better resistance in the Salt 1 environment, whereas SS304H performed better in Salt 2, as indicated by lower weight gain and parabolic rate constants. Higher chlorine and vanadium content accelerated corrosion, promoting cracks and voids from molten chlorides. Oxide scales formed at high temperatures were enriched with Ni, Cr, Fe, and O, alongside other reactive species.
- 20 March 2024
- Published by Springer Nature in Silicon
- Vol. 16 (9) , 3689-3707
Weld Chemistry and Microhardness Studies of Formulated SrO-CaF2-CaO- SiO2 Silica Based SMAW Electrode with Nickel Wire
- 20 March 2024
- Published by Springer Nature in Silicon
- Vol. 16 (9) , 3689-3707
Weld Chemistry and Microhardness Studies of Formulated SrO-CaF2-CaO- SiO2 Silica Based SMAW Electrode with Nickel Wire
- 2 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (8) , 1861-1873
Investigations on wetting and structural behavior using CaF2-SiO2-CaO-22.5%TiO2 SMAW electrode coating for AUSC applications
This study investigates the structural behavior and high-temperature wettability of a CaF2-SiO2-CaO-22.5%TiO2 shielded metal arc welding electrode coating for advanced ultra-supercritical power plant applications. The wettability parameters were measured, including contact angle, spread area, adhesion energy, and surface tension. Extreme vertices mixture design approaches were used to develop 13 different electrode coatings. To determine the contact angle at solid/liquid interface, circular pellets were made from powder samples and heated inside the furnace at 1125°C at a constant heating rate. Young's and Boni's equations are used to calculate the surface tension value for 13 coated samples using the calculated contact angle. Adhesion energy for 13 coated samples is calculated using Dupre's equation. Phases and structural behavior of coating samples were measured by Fourier transform infrared spectroscopy and X-ray diffraction. The developed regression model estimates the impact of primary ingredients and their interaction on the calculated wettability characteristics. CaF2.SiO2, CaO.SiO2, and CaO.CaF2 binary mixture is the more favorable and substantially impacts contact angle, whereas ternary interactions of CaO.SiO2.CaF2 shows an opposite effect on contact angle. Coating numbers 2 and 10 give better wetting behavior and spread area due to the low value of contact angles. Individual ingredient shows an increasing effect on surface tension and adhesion energy. Ternary component of CaO.CaF2.SiO2 is favorable and shows an increasing impact on adhesion energy.
- 2 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (8) , 1861-1873
Investigations on wetting and structural behavior using CaF2-SiO2-CaO-22.5%TiO2 SMAW electrode coating for AUSC applications
This study investigates the structural behavior and high-temperature wettability of a CaF2-SiO2-CaO-22.5%TiO2 shielded metal arc welding electrode coating for advanced ultra-supercritical power plant applications. The wettability parameters were measured, including contact angle, spread area, adhesion energy, and surface tension. Extreme vertices mixture design approaches were used to develop 13 different electrode coatings. To determine the contact angle at solid/liquid interface, circular pellets were made from powder samples and heated inside the furnace at 1125°C at a constant heating rate. Young's and Boni's equations are used to calculate the surface tension value for 13 coated samples using the calculated contact angle. Adhesion energy for 13 coated samples is calculated using Dupre's equation. Phases and structural behavior of coating samples were measured by Fourier transform infrared spectroscopy and X-ray diffraction. The developed regression model estimates the impact of primary ingredients and their interaction on the calculated wettability characteristics. CaF2.SiO2, CaO.SiO2, and CaO.CaF2 binary mixture is the more favorable and substantially impacts contact angle, whereas ternary interactions of CaO.SiO2.CaF2 shows an opposite effect on contact angle. Coating numbers 2 and 10 give better wetting behavior and spread area due to the low value of contact angles. Individual ingredient shows an increasing effect on surface tension and adhesion energy. Ternary component of CaO.CaF2.SiO2 is favorable and shows an increasing impact on adhesion energy.
- 6 October 2022
- Published by Springer Nature in Silicon
- Vol. 15 (4) , 1-14
Investigation on CaO-SiO2-CaF2-SrO Based Electrode Coating System on High-Temperature Wettability and Structural Behaviour for Power Plants Welds
- 6 October 2022
- Published by Springer Nature in Silicon
- Vol. 15 (4) , 1-14
Investigation on CaO-SiO2-CaF2-SrO Based Electrode Coating System on High-Temperature Wettability and Structural Behaviour for Power Plants Welds
- 3 August 2022
- Published by Springer Nature in Silicon
- Vol. 15 (2) , 739-753
Investigation on Thermophysical and Physicochemical Properties of CaO-SiO2-CaF2-22.5%TiO2 Silica Based Electrode Coating System
- 3 August 2022
- Published by Springer Nature in Silicon
- Vol. 15 (2) , 739-753
Investigation on Thermophysical and Physicochemical Properties of CaO-SiO2-CaF2-22.5%TiO2 Silica Based Electrode Coating System
- 19 July 2022
- Published by Springer Nature in Silicon
- Vol. 15 (1) , 305-319
Element Transfer Investigations on Silica Based Submerged Arc Welding Fluxes
- 19 July 2022
- Published by Springer Nature in Silicon
- Vol. 15 (1) , 305-319
Element Transfer Investigations on Silica Based Submerged Arc Welding Fluxes
- 17 June 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (19) , 28730-28738
Experimental investigation on SMAW electrode coatings developed using CaO–SiO2–CaF2–SrO based coating system
- 17 June 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (19) , 28730-28738
Experimental investigation on SMAW electrode coatings developed using CaO–SiO2–CaF2–SrO based coating system
- 7 April 2022
- Published by Springer Nature in Silicon
- Vol. 14 (17) , 11279-11291
Experimental Study on Wettability at High-Temperature Using TiO2-SiO2-CaO-Na3AlF6 Based Electrode Coating for AUSC Thermal Power Plant
- 7 April 2022
- Published by Springer Nature in Silicon
- Vol. 14 (17) , 11279-11291
Experimental Study on Wettability at High-Temperature Using TiO2-SiO2-CaO-Na3AlF6 Based Electrode Coating for AUSC Thermal Power Plant
- 8 March 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (12) , 17412-17424
Physicochemical and thermophysical properties of CaO–TiO2–SiO2–Na3AlF6 system based electrode coating for AUSC power plant
- 8 March 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (12) , 17412-17424
Physicochemical and thermophysical properties of CaO–TiO2–SiO2–Na3AlF6 system based electrode coating for AUSC power plant