MMMostafa A. Mohamed

Mostafa A. Mohamed

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Mostafa A. Mohamed has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Microstructure, hardness, and wear properties of AA6061/WC nanocomposite fabricated by friction stir processing

    by A.A. Megahed, Mostafa A Mohamed, M. Abdel Hamid, Said H Zoalfakar

    Friction stir processing (FSP) is a solid-state microstructural modification technique that has recently become an effective tool to refine microstructures and improve the mechanical properties of metals. In the current study, optimization of FSP parameters, including tool rotational speed, transverse feed, number of passes, and tungsten carbide (WC) nanoparticle volume fractions on mechanical and wear properties of the fabricated AA6061/WC nanocomposite was studied. Optical microscopy and scanning electron microscopy are used for microstructural observations. The process parameters are optimized using the Taguchi technique for single responses towards microhardness and weight loss and the Desirability approach for both responses. The percentage contribution of process parameters is estimated using analysis of variance. The microstructure observation shows that the proper selection of FSP parameters leads to a homogeneous dispersion of the WC particles throughout the matrix, thereby producing a defect-free AA6061/WC nanocomposite without voids. Also, the severe plastic deformation and heat generation during FSP cause the breaking of coarse particles, WC particles, and porous holes and create an ultrafine grain-sized structure via dynamic recrystallization. The results indicated that the microhardness value of the processed composite was found to be 144 VHN, which is 39.81% higher than that of the base metal. Also, the weight loss of all samples decreased as compared to the base metal. Also, it can be observed that the number of passes is the most significant factor for microhardness, with a 40.1% contribution, and for minimum weight loss, the volume fraction is the most significant factor, with a 56.94% contribution. The optimum process parameter combination was found to be 1800 rpm rotation speed, 120 mm/min of transverse feed, 6% volume fraction, and 3 passes that resulted in obtaining optimum values for micro hardness and weight loss. The surface composite developed in this research is considered a suitable material for applications demanding lightweight and enhanced surface properties, including automotive, aerospace, marine, defense, and transportation industries.


  • Effect of friction stir processing parameters on producing AA6061/ tungsten carbide nanocomposite

    by Said H. Zoalfakar, Mostafa A. Mohamed, M. Abdel Hamid, A. A. Megahed

    Friction stir processing (FSP) is a modern manufacturing strategy for improving the surface characteristics of materials by modifying their surface via localized plastic deformation. This research focuses on optimization process parameters for tungsten carbide-reinforced 6061 aluminum alloy surface composite using FSP. The effect of the process parameters including tool rotational speed, transverse feed, number of passes, and tungsten carbide particles volume fractions, on ultimate tensile strength (UTS) and grain size of fabricated AA6061/WC surface nanocomposites are investigated. For four factors and three levels, the L27 Taguchi technique is used to formulate the experimental design. The analysis of variance (ANOVA) is used to determine the significance and the percentage contribution of each parameter. The desirability approach is used to optimize the process parameters in terms of tensile strength and average grain size. The results indicate that the proper selection of FSP parameters results in a homogeneous distribution of the WC particles throughout the matrix thereby producing a defect-free AA6061/WC nanocomposite without voids. Also, the severe plastic deformation and heat generation during FSP causes the breaking of coarse particles, WC particles, elimination of porous holes and creates an ultrafine grain-sized structure via dynamic recrystallization. Furthermore, it was concluded that the transverse feed is the most significant factor for ultimate tensile strength with 40.1% contribution whereas the number of passes is the most significant factor for grain size with a 34.7% contribution. The optimum combination of the current process parameters is found to be 1800 rpm rotation speed, 120 mm/min transverse feed, 4.3636% volume fraction, and 3- pass for optimum values of UTS and grain size. The surface composite developed in this work is considered appropriate material for applications requiring lightweight and improved surface properties, such as aerospace, automotive, marine, defense and transportation industries.


  • Electrospun EGNPs reinforced precursor carbon nanofibril composites by using RSM

    by Said H. Zoalfakar, Mostafa A. Mohamed, Mohamed A. El‐Hamid, Ashraf A. Ali

    Response surface methodology (RSM),based on five‐level, four variable Box‐Benkhen technique was investigated for modeling the average fiber diameter of electrospun polyacrylonitrile (PAN) nanofibers. The four important electrospinning parameters were studied including applied voltage (kV), Berry's number, deposition distance from nozzle to collector (cm), and spinning angle (Ѳ in degree). The measured fiber diameters were in a good agreement with the predicted results by using RSM technique. High‐regression coefficient between the variables and the response ( R 2 = 87.74%) indicates excellent evaluation of experimental data by second‐order polynomial regression model. The optimum PAN average fiber diameters of 208 and 37‐nm standard deviation were collected at 19 kV, Berry's number = 10, 25 ° spinning angle, and 16‐cm deposition distance. The PAN/ N,N ‐dimethylformamide (DMF) polymer solution with the optimum weight concentration (10 wt.%) was selected to study the effect of dispersing exfoliated graphite nanoplatelets (EGNPs) in PAN/DMF solution on the electrospun EGNP/PAN fibril composite diameter. Five different EGNPs weight concentrations (2, 4, 6, 8, and 10 wt.%) were dispersed in the optimized PAN/DMF polymer solution. Morphology of EGNPs/PAN fibril composites and its distribution were investigated by scanning electron microscopy (SEM) to show the minimum fiber diameter for the above‐mentioned 5 wt. % of EGNPs. A minimum fibril composite diameter of 182 nm was obtained at 10 wt.% of EGNPs. Morphological characteristics of electrospun fibers and their distribution were tested by Raman spectroscopy, SEM, differential light scattering, and high‐resolution transmission electron microscopy.


  • A nanofibrous electrospun patch to maintain human mesenchymal cell stemness

    by L. Pandolfi, N. Toledano Furman, Xin Wang, C. Lupo, J. O. Martinez, M. Mohamed, F. Taraballi, E. Tasciotti

    Mesenchymal stem cells (MSCs) have been extensively investigated in regenerative medicine because of their crucial role in tissue healing. For these proper