JHJian He

Jian He

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jian He has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental and Numerical Investigation on Finned Vortex Reducer in a Rotating Cavity with a Radial Inflow

    by Jian He, Xiang Luo, Yang Bai, An Song, Tao Yang

    In aero-engines, a secondary air system is used to cool the rotor discs and seal cavities between rotor and stator parts. The pressure loss caused by bleed air can be effectively reduced by setting the finned vortex reducer. Thus, the bleed system design can be optimized by researching the flow structure and pressure loss of each section in the cavity with a finned vortex reducer. In this study, the influence of different installation positions of a finned vortex reducer on the pressure loss characteristics was investigated through experimental and numerical simulation methods, focusing on the radial inflow of the secondary air system. The results indicate that the inlet and outlet positions of the fins affect the flow structure in the cavity. The aerodynamic parameters (rotational Reynolds number ReΦ and mass flow rate coefficient Cw), together with the inlet and outlet radii of the fins, influence the pressure loss in the cavity. Considering the swirl ratio β constrained by the fins, a pressure loss model was established, which showed good agreement with the experimentally measured pressure loss. This model reflects the impact of the inlet and outlet positions of the fins on the pressure loss characteristics.


  • Open Access

    Particle Deposition in the Vicinity of Multiple Film Cooling Holes

    by Yubo Peng, Guoqiang Xu, Xiang Luo, Jian He, Dongdong Liu

    Particle deposition on film cooling surface is an engineering issue that degrades the thermal protection of turbine blade. Here, we present a combined experimental and numerical investigation on the particle deposition in the vicinity of multiple film cooling holes to reveal the effect of interactions between cooling outflows on particle deposition. The numerical simulation of film cooling with a group of three rows of straight film cooling holes is conducted and validated by experimental data with blowing ratios ranging from 0 to 0.08. Wax particles with size range from 5 to 40 μm are added in the heated mainstream to simulate the particle deposition in the experiment. The simulation results show the decrease of particle deposition with blowing ratio and various deposition characteristics in different regions of the surface. The flow fields from numerical results are analyzed in detail to illustrate deposition mechanism of the particles in different regions under the interactions of cooling outflows. The cooling air from the holes in the first row reduces the particle concentration near the wall but causes particle deposition in or between the tail regions by the generated flow disturbance. The cooling air from the latter hole separates the diluted flow in the upstream from the wall, and creates a tail region without particle deposition. This revealed particle deposition characteristics under the effect of outflows interaction can benefit the understanding of particle deposition in engineering applications, where multi-row of cooling holes are utilized.


  • Open Access

    Experimental Investigation on the Transpiration Cooling Characteristics of Sintered Wire Mesh in Plain Weave

    by Yubo Peng, Guoqiang Xu, Xiang Luo, Jian He, Dongdong Liu

    We experimentally investigate the transpiration cooling characteristics of a porous material, sintered wire mesh. Three samples with different porosities in a plain weave structure are tested with various blowing ratios in an open-loop wind tunnel with a heated mainstream flow. The temperature on the surface of the porous material is measured by an infrared camera to obtain the cooling efficiency. The measurements reveal nonuniform distributions of the surface temperature and the cooling efficiency in both the flow direction and the transverse direction. The averaged cooling efficiency on the surface first decreases and then increases with the blowing ratio, but increases and then decreases with the porosity of the material. The internal cooling by forced convection and its combination with the external film cooling from the transpiration cooling are considered to be attributed to those two cooling characteristics, respectively. Finally, we propose a modified blowing ratio to collapse the minima of the blowing ratio for all tested samples, providing an universal transition for the decreasing and increasing branches for all tested samples in the relation between averaged cooling efficiency and blowing ratio.