G. T. Alliott
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
G. T. Alliott has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
G. D. Wilcox
Department of Materials, Loughborough University, Loughborough, UK
1 shared publication- Geoffrey D. Wilcox
Department of Materials, Loughborough University, Loughborough, UK
1 shared publication R. L. Higginson
Department of Materials, Loughborough University, Loughborough, UK
1 shared publication- Rebecca L. Higginson
Department of Materials, Loughborough University, Loughborough, UK
1 shared publication
Latest Publications
- Open Access
- 6 January 2023
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 101 (2) , 72-78
Producing a thin coloured film on stainless steels – a review. Part 2: non-electrochemical and laser processes
The high lustre and desirable aesthetics of stainless steels have resulted in their application for decorative purposes in a variety of industries including homeware and automotive, but primarily in architecture. It is possible to further enhance the aesthetics of stainless steel by imparting a thin coloured film on the surface that does not impair any inherent desirable properties, including corrosion resistance. There are two different types of thin coloured films, iridescent and non-iridescent. Iridescent colour can visually change depending on the angle from which it is viewed and is a consequence of a phenomenon known as thin film interference. Non-iridescent colour is created by the absorbance of light waves of all but a given wavelength, the colour is intrinsic to the thin film and does not change with viewing angle. For the purpose of this review, colouring techniques have categorised into three groups, electrochemical, non-electrochemical and laser colouring. Laser colouring can be utilised as either an electrochemical or non-electrochemical process and is particularly suited to colouring small areas and intricate shapes. Non-electrochemical techniques, such as physical vapour deposition (PVD) and thermal tinting, avoid the use of toxic chemicals, however, they present other challenges, including energy consumption and scrappage rate. The use of non-electrochemical and laser techniques to colour stainless steel can negate the use of toxic hexavalent chromium; however, they are yet to be widely adopted by industry for this purpose. Therefore, it is important to consider each technique to understand why this is the case. The present Part 2 of the review discusses non-electrochemical and laser processes used to produce coloured films on stainless steel, whereas Part 1 discussed the electrochemical processes.
- 6 January 2023
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 101 (2) , 72-78
Open AccessProducing a thin coloured film on stainless steels – a review. Part 2: non-electrochemical and laser processes
The high lustre and desirable aesthetics of stainless steels have resulted in their application for decorative purposes in a variety of industries including homeware and automotive, but primarily in architecture. It is possible to further enhance the aesthetics of stainless steel by imparting a thin coloured film on the surface that does not impair any inherent desirable properties, including corrosion resistance. There are two different types of thin coloured films, iridescent and non-iridescent. Iridescent colour can visually change depending on the angle from which it is viewed and is a consequence of a phenomenon known as thin film interference. Non-iridescent colour is created by the absorbance of light waves of all but a given wavelength, the colour is intrinsic to the thin film and does not change with viewing angle. For the purpose of this review, colouring techniques have categorised into three groups, electrochemical, non-electrochemical and laser colouring. Laser colouring can be utilised as either an electrochemical or non-electrochemical process and is particularly suited to colouring small areas and intricate shapes. Non-electrochemical techniques, such as physical vapour deposition (PVD) and thermal tinting, avoid the use of toxic chemicals, however, they present other challenges, including energy consumption and scrappage rate. The use of non-electrochemical and laser techniques to colour stainless steel can negate the use of toxic hexavalent chromium; however, they are yet to be widely adopted by industry for this purpose. Therefore, it is important to consider each technique to understand why this is the case. The present Part 2 of the review discusses non-electrochemical and laser processes used to produce coloured films on stainless steel, whereas Part 1 discussed the electrochemical processes.
- Open Access
- 16 March 2022
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 100 (3) , 128-137
Producing a thin coloured film on stainless steels – a review. Part 1: electrochemical processes
Stainless steels are often used for decorative purposes, primarily in the architectural industry, but also in homeware and the automotive industry, among others. It is possible to impart colour on articles to enhance aesthetics without impairing the desirable properties of the stainless steel itself. The colour can be non-iridescent and created by the absorbance of light waves of all but a given wavelength, or iridescent and created by a phenomenon known as thin-film interference. Colouring methods have been categorised into three groups, electrochemical, non-electrochemical and laser colouring. Laser colouring can be utilised as either an electrochemical or non-electrochemical process. The colouring technique most widely adopted by industry is a 2-stage electrochemical process, known as the INCO process, which utilises chromic-sulphuric acid baths to produce a thin interference film on the stainless steel surface. Alternatives developed by investigators regularly cite the toxicity of hexavalent chromium as motivation for their work and use the INCO process as a benchmark. Authors claim that alternative techniques match or exceed many of the properties achieved through colouring using hexavalent chromium, however, none are yet widely adopted by industry for the purpose of colouring stainless steel. It is therefore important to consider each technique to understand why this is the case. Part 1 of this review discusses the electrochemical processes utilised to produce coloured films on stainless steel, and Part 2 discusses non-electrochemical and laser processes.
- 16 March 2022
- Published by Taylor & Francis in Transactions of the IMF
- Vol. 100 (3) , 128-137
Open AccessProducing a thin coloured film on stainless steels – a review. Part 1: electrochemical processes
Stainless steels are often used for decorative purposes, primarily in the architectural industry, but also in homeware and the automotive industry, among others. It is possible to impart colour on articles to enhance aesthetics without impairing the desirable properties of the stainless steel itself. The colour can be non-iridescent and created by the absorbance of light waves of all but a given wavelength, or iridescent and created by a phenomenon known as thin-film interference. Colouring methods have been categorised into three groups, electrochemical, non-electrochemical and laser colouring. Laser colouring can be utilised as either an electrochemical or non-electrochemical process. The colouring technique most widely adopted by industry is a 2-stage electrochemical process, known as the INCO process, which utilises chromic-sulphuric acid baths to produce a thin interference film on the stainless steel surface. Alternatives developed by investigators regularly cite the toxicity of hexavalent chromium as motivation for their work and use the INCO process as a benchmark. Authors claim that alternative techniques match or exceed many of the properties achieved through colouring using hexavalent chromium, however, none are yet widely adopted by industry for the purpose of colouring stainless steel. It is therefore important to consider each technique to understand why this is the case. Part 1 of this review discusses the electrochemical processes utilised to produce coloured films on stainless steel, and Part 2 discusses non-electrochemical and laser processes.