Xu Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xu Han has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Gang Ji
Univ. Lille, CNRS, INRA, ENSCL, UMR 8207–UMET–Unité Matériaux et Transformations, Lille, France
1 shared publication - Gangli Yang
College of Materials Science and Engineering, Beijing University of Technology , No. 100 Ping Le Yuan, Chaoyang District, Beijing 100124, China
1 shared publication Hu Zhang
College of Materials Science and Engineering, Beijing University of Technology , No. 100 Ping Le Yuan, Chaoyang District, Beijing 100124, China
1 shared publicationLinjie Wen
College of Materials Science and Engineering, Beijing University of Technology , No. 100 Ping Le Yuan, Chaoyang District, Beijing 100124, China
1 shared publicationShanshan Li
College of Materials Science and Engineering, Beijing University of Technology , No. 100 Ping Le Yuan, Chaoyang District, Beijing 100124, China
1 shared publicationXiaoyan Li
College of Materials Science and Engineering, Beijing University of Technology , No. 100 Ping Le Yuan, Chaoyang District, Beijing 100124, China
1 shared publication
Latest Publications
- 9 December 2022
- Published by ASME International in Journal of Electronic Packaging
- Vol. 145 (3) , 1-22
Study on the Microstructure Evolution and Mechanical Properties of Cu/Cu41Sn11/Cu Solder Joint During High-Temperature Aging
The paper focused on the changes in microstructure and mechanical properties of the full Cu41Sn11 solder joint (Cu/Cu41Sn11/Cu) during isothermal aging at 420 °C. It was motivated by potential applications of Cu–Sn intermetallic compounds (IMCs) solder joint in third-generation wide bandgap semiconductor devices. Experimental results revealed that the Cu41Sn11 phase was unstable under high-temperature conditions, the full Cu41Sn11 joint transformed into the full α(Cu) joint (Cu/α(Cu)/Cu) joint at 150 h during thermal aging. The formed α(Cu) phase was a Cu solid solution with inhomogeneous Sn atomic concentration, and its crystal structure and orientation were consistent with the original Cu plate. The conversion of the Cu41Sn11 to α(Cu) was accompanied by the formation of voids due to the volume shrinkage effect, predominantly near the middle of the solder joint interface. The α(Cu) solder joint presented a decrease in strength but an increase in strain rate sensitivity index compared to the Cu41Sn11 solder joint. Furthermore, the strain rate sensitivity index of α(Cu) and Cu41Sn11 is lower than that of ordinary Sn solders. After the shear test, the fractures that occurred in Cu41Sn11 grains were brittle, while the fractures in α(Cu) grains were ductile.
- 9 December 2022
- Published by ASME International in Journal of Electronic Packaging
- Vol. 145 (3) , 1-22
Study on the Microstructure Evolution and Mechanical Properties of Cu/Cu41Sn11/Cu Solder Joint During High-Temperature Aging
The paper focused on the changes in microstructure and mechanical properties of the full Cu41Sn11 solder joint (Cu/Cu41Sn11/Cu) during isothermal aging at 420 °C. It was motivated by potential applications of Cu–Sn intermetallic compounds (IMCs) solder joint in third-generation wide bandgap semiconductor devices. Experimental results revealed that the Cu41Sn11 phase was unstable under high-temperature conditions, the full Cu41Sn11 joint transformed into the full α(Cu) joint (Cu/α(Cu)/Cu) joint at 150 h during thermal aging. The formed α(Cu) phase was a Cu solid solution with inhomogeneous Sn atomic concentration, and its crystal structure and orientation were consistent with the original Cu plate. The conversion of the Cu41Sn11 to α(Cu) was accompanied by the formation of voids due to the volume shrinkage effect, predominantly near the middle of the solder joint interface. The α(Cu) solder joint presented a decrease in strength but an increase in strain rate sensitivity index compared to the Cu41Sn11 solder joint. Furthermore, the strain rate sensitivity index of α(Cu) and Cu41Sn11 is lower than that of ordinary Sn solders. After the shear test, the fractures that occurred in Cu41Sn11 grains were brittle, while the fractures in α(Cu) grains were ductile.
- 18 March 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (13) , 10677-10692
On the study of morphological characteristics and growth mechanism of intermetallic compounds in ultrasonically fabricated Cu–Sn solder joints
- 18 March 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (13) , 10677-10692
On the study of morphological characteristics and growth mechanism of intermetallic compounds in ultrasonically fabricated Cu–Sn solder joints