Lyubov Furda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lyubov Furda has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Olga Evgenievna Lebedeva
Belgorod State National Research University
3 shared publications - Evgeniy S. Seliverstov
Belgorod State National Research University
2 shared publications - Sergei N. Golovin
Institute of Pharmacy, Chemistry and Biology, Department of General Chemistry, Belgorod State National Research University, 308015 Belgorod, Russia
2 shared publications - Dmitry Smalchenko
Institute of Pharmacy, Chemistry and Biology, Belgorod State National Research University (BelSU), Belgorod, Russia
1 shared publication - Ekaterina Migulina
Institute of Pharmacy, Chemistry and Biology, Department of General Chemistry, Belgorod State National Research University, 308015 Belgorod, Russia
1 shared publication - Igor Tarasov
Institute of Pharmacy, Chemistry and Biology, Department of General Chemistry, Belgorod State National Research University, 308015 Belgorod, Russia
1 shared publication
Latest Publications
- Open Access
Polypropylene Waste Valorization via Pyrolysis: Assessing the Interchangeability of Low-Cost Montmorillonite Clay Catalysts
Numerous efficient catalysts have been developed for plastic pyrolysis; however, their relatively high cost limits their practical application in waste valorization. Natural clays are among the most promising low-cost catalytic materials because of their abundance and availability. Their wider application is limited by concerns regarding the reproducibility of catalytic performance. The current study was designed to answer the question of whether montmorillonite-rich clays from different deposits are interchangeable in polypropylene pyrolysis. Pyrolysis of polypropylene-based plastic was carried out in a flow fixed-bed reactor in inert atmosphere. Four samples of natural montmorillonite-containing clays from deposits in Russia and Kazakhstan with similar chemical composition were used as catalysts. Liquid products of the pyrolysis were analyzed using one-dimensional (1H, 13C) and two-dimensional (COSY and HSQC) NMR spectroscopy to assess the similarity of their molecular compositions. NMR analysis revealed that all pyrolysis oils consisted mainly of aliphatic hydrocarbons, accompanied by olefins and only minor aromatic fractions. The relative proportions of the major groups of compounds as well as research octane numbers were highly similar for all clay catalysts. The results indicate that the use of montmorillonite-containing clays with comparable mineralogical and chemical characteristics can ensure reproducible product composition, providing flexibility in catalyst selection for polypropylene pyrolysis.
Open AccessPolypropylene Waste Valorization via Pyrolysis: Assessing the Interchangeability of Low-Cost Montmorillonite Clay Catalysts
Numerous efficient catalysts have been developed for plastic pyrolysis; however, their relatively high cost limits their practical application in waste valorization. Natural clays are among the most promising low-cost catalytic materials because of their abundance and availability. Their wider application is limited by concerns regarding the reproducibility of catalytic performance. The current study was designed to answer the question of whether montmorillonite-rich clays from different deposits are interchangeable in polypropylene pyrolysis. Pyrolysis of polypropylene-based plastic was carried out in a flow fixed-bed reactor in inert atmosphere. Four samples of natural montmorillonite-containing clays from deposits in Russia and Kazakhstan with similar chemical composition were used as catalysts. Liquid products of the pyrolysis were analyzed using one-dimensional (1H, 13C) and two-dimensional (COSY and HSQC) NMR spectroscopy to assess the similarity of their molecular compositions. NMR analysis revealed that all pyrolysis oils consisted mainly of aliphatic hydrocarbons, accompanied by olefins and only minor aromatic fractions. The relative proportions of the major groups of compounds as well as research octane numbers were highly similar for all clay catalysts. The results indicate that the use of montmorillonite-containing clays with comparable mineralogical and chemical characteristics can ensure reproducible product composition, providing flexibility in catalyst selection for polypropylene pyrolysis.
- Open Access
NMR Characterization of Plastic Pyrolysis Oils Obtained over Clay Catalysts
The accumulation of plastic waste has become a significant environmental challenge, stimulating the development of efficient recycling technologies capable of converting polymers into valuable products. In this study, polypropylene wastes were thermocatalytically converted into liquid hydrocarbons using three naturally occurring types of clay as catalysts, namely, kaolin, illite, and bentonite. The obtained liquid products were investigated using one- and two-dimensional NMR spectroscopy, including 1H, 13C, and COSY techniques. Quantitative evaluation of hydrocarbon group composition was performed using established NMR correlations to determine the content of paraffins, olefins and aromatic compounds as well as fuel-related parameters. The results demonstrated that paraffins were the predominant constituents in all pyrolysis oils, accounting for more than 70 vol.%, while olefins and aromatics were present in smaller amounts. Although all catalysts promoted the formation of liquid mixtures of hydrocarbon, noticeable differences in product composition were observed. Oil obtained over illite exhibited increased aromaticity and lower olefin content, whereas kaolin produced a product characterized by the highest isoparaffin index and estimated research octane number. The findings indicate that variations in catalysts influence the characteristics of polypropylene-derived oils and may be used to tailor products’ properties for their utilization as fuel additives or petrochemical feedstocks.
Open AccessNMR Characterization of Plastic Pyrolysis Oils Obtained over Clay Catalysts
The accumulation of plastic waste has become a significant environmental challenge, stimulating the development of efficient recycling technologies capable of converting polymers into valuable products. In this study, polypropylene wastes were thermocatalytically converted into liquid hydrocarbons using three naturally occurring types of clay as catalysts, namely, kaolin, illite, and bentonite. The obtained liquid products were investigated using one- and two-dimensional NMR spectroscopy, including 1H, 13C, and COSY techniques. Quantitative evaluation of hydrocarbon group composition was performed using established NMR correlations to determine the content of paraffins, olefins and aromatic compounds as well as fuel-related parameters. The results demonstrated that paraffins were the predominant constituents in all pyrolysis oils, accounting for more than 70 vol.%, while olefins and aromatics were present in smaller amounts. Although all catalysts promoted the formation of liquid mixtures of hydrocarbon, noticeable differences in product composition were observed. Oil obtained over illite exhibited increased aromaticity and lower olefin content, whereas kaolin produced a product characterized by the highest isoparaffin index and estimated research octane number. The findings indicate that variations in catalysts influence the characteristics of polypropylene-derived oils and may be used to tailor products’ properties for their utilization as fuel additives or petrochemical feedstocks.
- Open Access
- 18 March 2022
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 62 (3) , 310-315
Catalytic Conversion of Polyolefins in the Presence of MCM-41 Type Mesoporous Materials
The catalytic activities of mesoporous H–MCM-41 aluminosilicates of different compositions in degradation of polypropylene and a polypropylene-polyethylene mixture into gasoline-range fraction hydrocarbons were compared. A higher yield of the target products (86 wt %) was observed for the sample with a lower aluminum content. Using the results of chromatographic analysis of the catalyzate for the content of the gasoline-range fraction, both saturated and unsaturated hydrocarbons, dominated by products with cyclic structure, were identified in all the samples studied. In the presence of the H–MCM-41 sample with a lower silica modulus, a larger amount of condensation products with a higher calorific value arose from polypropylene degradation. Mesoporous aluminosilicates H–MCM-41 can be regarded as effective catalysts for thermocatalytic conversion of polypropylene to produce the gasoline-range fraction.
- 18 March 2022
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 62 (3) , 310-315
Open AccessCatalytic Conversion of Polyolefins in the Presence of MCM-41 Type Mesoporous Materials
The catalytic activities of mesoporous H–MCM-41 aluminosilicates of different compositions in degradation of polypropylene and a polypropylene-polyethylene mixture into gasoline-range fraction hydrocarbons were compared. A higher yield of the target products (86 wt %) was observed for the sample with a lower aluminum content. Using the results of chromatographic analysis of the catalyzate for the content of the gasoline-range fraction, both saturated and unsaturated hydrocarbons, dominated by products with cyclic structure, were identified in all the samples studied. In the presence of the H–MCM-41 sample with a lower silica modulus, a larger amount of condensation products with a higher calorific value arose from polypropylene degradation. Mesoporous aluminosilicates H–MCM-41 can be regarded as effective catalysts for thermocatalytic conversion of polypropylene to produce the gasoline-range fraction.