HMHonggang Mei

Honggang Mei

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Honggang Mei has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Lei Li

    College of Chemistry and Chemical Engineering and the State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, China

    2 shared publications
  • Sixun Zheng

    Shanghai Jiao Tong University

    2 shared publications
  • Guohua Hang

    Department of Polymer Science and Engineering and the State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, China

    1 shared publication
  • Huaming Wang

    Department of Polymer Science and Engineering and the State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, China

    1 shared publication
  • Weiming Liu

    Department of Polymer Science and Engineering, The State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, China

    1 shared publication

Latest Publications

  • Open Access

    Generation of One-Dimensional Fibrous Polyethylene Nanocrystals in Epoxy Thermosets

    by Honggang Mei, Huaming Wang, Lei Li, Sixun Zheng

    The one-dimensional (1D) polyethylene (PE) nanocrystals were generated in epoxy thermosets via crystallization-driven self-assembly. Toward this end, an ABA triblock copolymer composed of PE midblock and poly(ε-caprolactone) (PCL) endblocks was synthesized via the ring opening metathesis polymerization followed by hydrogenation approach. The nanostructured thermosets were obtained via a two-step curing approach, i.e., the samples were cured first at 80 °C and then at 150 °C. Under this condition, the one-dimensional (1D) fibrous PE microdomains with the lengths up to a couple of micrometers were created in epoxy thermosets. In contrast, only the spherical PE microdomains were generated while the thermosets were cured via a one-step curing at 150 °C. By the use of the triblock copolymer, the generation of 1D fibrous PE nanocrystals is attributable to crystallization-driven self-assembly mechanism whereas that of the spherical PE microdomains follows traditional self-assembly mechanism. Compared to the thermosets containing the spherical PE microdomains, the thermosets containing the 1D fibrous PE nanocrystals displayed quite different thermal and mechanical properties. More importantly, the nanostructured thermosets containing the 1D fibrous PE nanocrystals displayed the fracture toughness much higher than those only containing the spherical PE nanocrystals; the KIC value was even three times as that of control epoxy.


  • Open Access

    Nanocomposites of Polyhydroxyurethane with POSS Microdomains: Synthesis via Non-Isocyanate Approach, Morphologies and Reprocessing Properties

    by Weiming Liu, Guohua Hang, Honggang Mei, Lei Li, Sixun Zheng

    In this contribution, we reported the synthesis of a novel trifunctional POSS cyclic carbonate [POSS-3(5CC)]. With a difunctional five-member cyclic carbonate and a trifunctional polyetheramine as the precursor, the nanocomposites of polyhydroxyurethane (PHU) with POSS were synthesized. Transmission electron microscopy (TEM) showed that the nanocomposites of PHUs with POSS were microphase-separated; the spherical POSS microdomains via POSS-POSS interactions were generated with the size of 20~40 nm in diameter. After the introduction of POSS microdomains, the nanocomposites displayed improved thermal and mechanical properties. More importantly, the nanocomposites still displayed the reprocessing properties of vitrimers.