Zeeshan Anjum
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zeeshan Anjum has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Masood Shah
Department of Mechanical Engineering, University of Engineering and Technology, Taxila, Punjab, Pakistan
4 shared publications- Faisal Qayyum
Institut für Metallformung, Technische Universität Bergakademie Freiberg, 09599 Freiberg, Germany
2 shared publications Ali Nasir
University of Engineering and Technology Taxila
1 shared publicationFaisal Qayyum
Technische Universität Bergakademie Freiberg (Sachsen)
1 shared publicationFaryal Khan
University of Engineering and Technology Taxila
1 shared publicationFurqan Mukhtar
1 shared publication
Latest Publications
- 23 August 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (11) , 4953-4965
Fretting Fatigue Performance of Ti6Al4V Dovetail Joints Under Dimple Surface Texturing
In this work, a specially designed test fixture was used to investigate the effect of dimple surface texturing on the fretting fatigue performance of a Ti6Al4V dovetail joint. The novel geometry of the fretting pair offered simultaneous investigation under cylinder‐on‐flat and flat‐on‐flat contact configurations. Tests were conducted using a servo‐hydraulic fatigue machine under an axial cyclic load of 11 kN, a stress ratio of 0.05, and a frequency of 10 Hz. The dimple surface textures having densities of 19.6%, 12.6%, and 8.7% were fabricated using laser surface texturing. Microscopic investigations were conducted using an optical microscope, a scanning electron microscope, and a three‐dimensional wear microscope. An enhanced fretting fatigue life was observed at the highest texture density of 19.6%, causing a delay in the crack initiation and reducing the crack growth. SEM revealed a large amount of wear debris, oxidation, spalling, and debris at the higher texture densities.
- 23 August 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (11) , 4953-4965
Fretting Fatigue Performance of Ti6Al4V Dovetail Joints Under Dimple Surface Texturing
In this work, a specially designed test fixture was used to investigate the effect of dimple surface texturing on the fretting fatigue performance of a Ti6Al4V dovetail joint. The novel geometry of the fretting pair offered simultaneous investigation under cylinder‐on‐flat and flat‐on‐flat contact configurations. Tests were conducted using a servo‐hydraulic fatigue machine under an axial cyclic load of 11 kN, a stress ratio of 0.05, and a frequency of 10 Hz. The dimple surface textures having densities of 19.6%, 12.6%, and 8.7% were fabricated using laser surface texturing. Microscopic investigations were conducted using an optical microscope, a scanning electron microscope, and a three‐dimensional wear microscope. An enhanced fretting fatigue life was observed at the highest texture density of 19.6%, causing a delay in the crack initiation and reducing the crack growth. SEM revealed a large amount of wear debris, oxidation, spalling, and debris at the higher texture densities.
- 5 January 2023
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 37 (1) , 119-126
Prediction of crack initiation and propagation during fretting corrosion of novel Ti6Al4V specimens in saline and physiological environments
- 5 January 2023
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 37 (1) , 119-126
Prediction of crack initiation and propagation during fretting corrosion of novel Ti6Al4V specimens in saline and physiological environments
- 21 November 2017
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 31 (11) , 5265-5272
Effect of various surface preparation techniques on the delamination properties of vacuum infused Carbon fiber reinforced aluminum laminates (CARALL): Experimentation and numerical simulation
- 21 November 2017
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 31 (11) , 5265-5272
Effect of various surface preparation techniques on the delamination properties of vacuum infused Carbon fiber reinforced aluminum laminates (CARALL): Experimentation and numerical simulation
- 1 December 2015
- Published by Elsevier in Materials & Design
- Vol. 87, 750-758
Prediction of non-propagating fretting fatigue cracks in Ti6Al4V sheet tested under pin-in-dovetail configuration: Experimentation and numerical simulation
- 1 December 2015
- Published by Elsevier in Materials & Design
- Vol. 87, 750-758
Prediction of non-propagating fretting fatigue cracks in Ti6Al4V sheet tested under pin-in-dovetail configuration: Experimentation and numerical simulation