Si Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Si Li has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Yunlong Mao
Jiangsu University of Science and Technology
9 shared publications - Wenxing Li
The College of Information and Communication Engineering, Harbin Engineering University, Harbin 150009, China
4 shared publications - Atef. Z. Elsherbeni
Colorado School of Mines, Golden, CO, USA
3 shared publications - Bin Yang
School of Cyberspace, Hangzhou Dianzi University, Hangzhou 310018, China
3 shared publications - Qi Zhang
Aviation Ammunition Research Institute of China North Industries Group , Harbin , China
3 shared publications - Cheng Lyu
College of Information And Communication Engineering, Harbin Engineering University, Harbin 150000, China
2 shared publications
Latest Publications
- Open Access
- 30 November 2025
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
A Miniaturized Dual-Band Circularly Polarized Antenna With Broadband and Flexible Frequency Ratio
A dual-band circularly polarized antenna with AR (Axial Ratio) bandwidth enhanced using parasitic strips and triangle notches is proposed in this paper. The proposed antenna comes with a size of 53×53×3.813 mm (0.64λg×0.64λg×0.046λg at 2.45 GHz), which is composed of two layers of substrate and three layers of metallic patterns. With the introduction of parasitic strips on the top metallic layer and etched triangles on the ground plane, this antenna exhibits dual-band circularly polarized character. A flexible frequency ratio from 1.57 to 2.01 could be obtained by changing the size of the triangle notches. Simulations and measurements verified that the proposed antenna shows relative S11<-10 dB bandwidth of 36.6% (2.23–3.25 GHz) and 51.3% (3.58–6.05 GHz), relative AR<3 dB bandwidth of 17.6% (2.32–2.77 GHz) and 11.1% (4.65–5.30 GHz), peak gains of 4.45 dBic and 6.24 dBic, respectively. This antenna is a good candidate for the 2.45 GHz communication band and the 5G sub-6 NR band applications.
- 30 November 2025
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
Open AccessA Miniaturized Dual-Band Circularly Polarized Antenna With Broadband and Flexible Frequency Ratio
A dual-band circularly polarized antenna with AR (Axial Ratio) bandwidth enhanced using parasitic strips and triangle notches is proposed in this paper. The proposed antenna comes with a size of 53×53×3.813 mm (0.64λg×0.64λg×0.046λg at 2.45 GHz), which is composed of two layers of substrate and three layers of metallic patterns. With the introduction of parasitic strips on the top metallic layer and etched triangles on the ground plane, this antenna exhibits dual-band circularly polarized character. A flexible frequency ratio from 1.57 to 2.01 could be obtained by changing the size of the triangle notches. Simulations and measurements verified that the proposed antenna shows relative S11<-10 dB bandwidth of 36.6% (2.23–3.25 GHz) and 51.3% (3.58–6.05 GHz), relative AR<3 dB bandwidth of 17.6% (2.32–2.77 GHz) and 11.1% (4.65–5.30 GHz), peak gains of 4.45 dBic and 6.24 dBic, respectively. This antenna is a good candidate for the 2.45 GHz communication band and the 5G sub-6 NR band applications.
- Open Access
- 30 October 2025
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
- p. 971–982
An Adaptive Multi-Objective Particle Swarm Optimization Algorithm for Excitation of Focused Phased Array in Microwave Hyperthermia Treatment Planning
A novel adaptive multi-objective particle swarm optimization (AMOPSO) is proposed to address the focus shift and redundant hotspots issues prevalent in current microwave hyperthermia treatment planning for breast cancer. By optimizing the excitation of phased array elements, more accurate beam focusing effect is achieved and the redundant hotspots are reduced, which significantly improves the treatment of breast cancer. The algorithm uses the difference between the optimized and target results as a feedback to self-constrain the algorithm, and introduces ratio of the peak power absorption (pPA) between the redundant hotspots and the target hotspot as a key objective function to reduce the number of redundant hotspots. Compared with the existing hyperthermia treatment planning (HTP) optimization algorithms, the proposed algorithm is capable of achieving precise focusing and a more substantial reduction in the number of redundant hotspots in a shorter computation time. Furthermore, the introduction of the pPA is capable of more effectively reducing the number of redundant hotspots and achieving a lower damage rate to healthy tissues.
- 30 October 2025
- Published by River Publishers in Applied Computational Electromagnetics Society Journal (ACES)
- p. 971–982
Open AccessAn Adaptive Multi-Objective Particle Swarm Optimization Algorithm for Excitation of Focused Phased Array in Microwave Hyperthermia Treatment Planning
A novel adaptive multi-objective particle swarm optimization (AMOPSO) is proposed to address the focus shift and redundant hotspots issues prevalent in current microwave hyperthermia treatment planning for breast cancer. By optimizing the excitation of phased array elements, more accurate beam focusing effect is achieved and the redundant hotspots are reduced, which significantly improves the treatment of breast cancer. The algorithm uses the difference between the optimized and target results as a feedback to self-constrain the algorithm, and introduces ratio of the peak power absorption (pPA) between the redundant hotspots and the target hotspot as a key objective function to reduce the number of redundant hotspots. Compared with the existing hyperthermia treatment planning (HTP) optimization algorithms, the proposed algorithm is capable of achieving precise focusing and a more substantial reduction in the number of redundant hotspots in a shorter computation time. Furthermore, the introduction of the pPA is capable of more effectively reducing the number of redundant hotspots and achieving a lower damage rate to healthy tissues.
- Open Access
- 27 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1327
A Novel Two-Stage Superpixel CFAR Method Based on Truncated KDE Model for Target Detection in SAR Images
Target detection in synthetic aperture radar (SAR) imagery remains a significant technical challenge, particularly in scenarios involving multi-target interference and clutter edge effects that cannot be disregarded, notably in high-resolution imaging applications. To tackle this issue, a novel two-stage superpixel-level constant false-alarm rate (CFAR) detection method based on a truncated kernel density estimation (KDE) model is proposed in this article. The contribution mainly lies in three aspects. First, a truncated KDE model is used to fit the statistical distribution of clutter in the detection window, and adaptive thresholding is used for clutter truncation to remove outliers from the clutter samples while preserving the real clutter. Second, based on the clutter statistics, the KDE model is accurately constructed using the quartile based on the truncated clutter statistics. Third, target superpixel detection is performed using a two-stage CFAR detection scheme enhanced with local contrast measure (LCM), consisting of a global stage followed by a local stage. In the global detection phase, we identify candidate target superpixels (CTSs) based on the superpixel segmentation results. In the local detection phase, a local CFAR detector using a truncated KDE model is employed to improve the detection process, and further screening is performed on the global detection results combined with local contrast. Experimental results show that the proposed method achieves excellent detection performance, while significantly reducing detection time compared to current popular methods.
- 27 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1327
Open AccessA Novel Two-Stage Superpixel CFAR Method Based on Truncated KDE Model for Target Detection in SAR Images
Target detection in synthetic aperture radar (SAR) imagery remains a significant technical challenge, particularly in scenarios involving multi-target interference and clutter edge effects that cannot be disregarded, notably in high-resolution imaging applications. To tackle this issue, a novel two-stage superpixel-level constant false-alarm rate (CFAR) detection method based on a truncated kernel density estimation (KDE) model is proposed in this article. The contribution mainly lies in three aspects. First, a truncated KDE model is used to fit the statistical distribution of clutter in the detection window, and adaptive thresholding is used for clutter truncation to remove outliers from the clutter samples while preserving the real clutter. Second, based on the clutter statistics, the KDE model is accurately constructed using the quartile based on the truncated clutter statistics. Third, target superpixel detection is performed using a two-stage CFAR detection scheme enhanced with local contrast measure (LCM), consisting of a global stage followed by a local stage. In the global detection phase, we identify candidate target superpixels (CTSs) based on the superpixel segmentation results. In the local detection phase, a local CFAR detector using a truncated KDE model is employed to improve the detection process, and further screening is performed on the global detection results combined with local contrast. Experimental results show that the proposed method achieves excellent detection performance, while significantly reducing detection time compared to current popular methods.
- 8 December 2024
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 66 (12)
A Novel Metasurface Antenna With Enhanced CP Bandwidth Through Decreasing Q Factor
This letter presents a novel metasurface antenna with improved axial ratio bandwidth using parasitic annular sector strips which decreased the Q factor. First, a metasurface antenna composed of a circular patch with etched annular cracks was designed and analyzed through characteristic analysis. Later, to enhance the axial bandwidth, four annular sector parasitic strips were added to decrease the Q factor based on transmission line analysis. In the end, the proposed antenna is fabricated and measured. The results show that the proposed antenna operates in the frequency band from 8.77 to 9.68 GHz; its 3 dB axial ratio bandwidth is 9.19–9.62 GHz, which is significantly improved by 119% compared to the case without the parasitic strips; the maximum gain is 7.2 dBic, which makes it a good candidate for marine search and rescue communications.
- 8 December 2024
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 66 (12)
A Novel Metasurface Antenna With Enhanced CP Bandwidth Through Decreasing Q Factor
This letter presents a novel metasurface antenna with improved axial ratio bandwidth using parasitic annular sector strips which decreased the Q factor. First, a metasurface antenna composed of a circular patch with etched annular cracks was designed and analyzed through characteristic analysis. Later, to enhance the axial bandwidth, four annular sector parasitic strips were added to decrease the Q factor based on transmission line analysis. In the end, the proposed antenna is fabricated and measured. The results show that the proposed antenna operates in the frequency band from 8.77 to 9.68 GHz; its 3 dB axial ratio bandwidth is 9.19–9.62 GHz, which is significantly improved by 119% compared to the case without the parasitic strips; the maximum gain is 7.2 dBic, which makes it a good candidate for marine search and rescue communications.
- 18 April 2024
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 66 (4)
A novel single‐layer dual‐band circularly polarized metasurface antenna for maritime communications
In this article, a novel single‐layer dual‐band circularly polarized (CP) metasurface antenna for maritime applications is proposed. The metasurface is composed of 4 × 4 hexagonal patches with two different sizes printed on one side of the low‐profile FR4 substrate, while a slot antenna is printed on the other side. A slit is etched in the middle of each hexagonal patch to enhance modal significance, forcing the current flows to be orthogonal to each other at different modes, generating CP waves as identified with characteristic modal analysis. The proposed antenna has been fabricated and measured. Simulated and measured results match well, of which the impedance bandwidth is 55.96% (4.8–8.53 GHz), 3 dB axial ratio bandwidth is 2.7% from 5.46 to 5.61 GHz with a maximum gain of 9.58 dBic and 8.2% from 7.86 to 8.53 GHz with a maximum gain of 9.02 dBic. The proposed antenna is structurally stable, and is applicable for maritime radio navigation and communication services.
- 18 April 2024
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 66 (4)
A novel single‐layer dual‐band circularly polarized metasurface antenna for maritime communications
In this article, a novel single‐layer dual‐band circularly polarized (CP) metasurface antenna for maritime applications is proposed. The metasurface is composed of 4 × 4 hexagonal patches with two different sizes printed on one side of the low‐profile FR4 substrate, while a slot antenna is printed on the other side. A slit is etched in the middle of each hexagonal patch to enhance modal significance, forcing the current flows to be orthogonal to each other at different modes, generating CP waves as identified with characteristic modal analysis. The proposed antenna has been fabricated and measured. Simulated and measured results match well, of which the impedance bandwidth is 55.96% (4.8–8.53 GHz), 3 dB axial ratio bandwidth is 2.7% from 5.46 to 5.61 GHz with a maximum gain of 9.58 dBic and 8.2% from 7.86 to 8.53 GHz with a maximum gain of 9.02 dBic. The proposed antenna is structurally stable, and is applicable for maritime radio navigation and communication services.
- Open Access
- 23 January 2024
- Published by Hindawi Limited in Journal of Sensors
- Vol. 2024, 1-17
A High Degree of Freedom Radiation Near-Field Source Localization Algorithm with Gain–Phase Error
The limitation of the number of estimable sources in the localization of radiation near-field sources with gainphase error is examined in this paper. When only the reference element has no gainphase error, a new method based on an accurate model is proposed to enhance the maximum number of estimable sources. Based on the location parameter details of the auxiliary source, the method first derives the gainphase error estimate matrix. Second, the source steering vector including errors is estimated using the total least square estimating signal parameter via rotational invariance techniques (TLS-ESPRIT), and the time-shifted data matrix is built utilizing the spacetime combination idea, thus increasing the degree of freedom of the array. Then, the source steering vector containing the error is modified by the error compensation matrix constructed according to the moment of gainphase error estimation. Finally, the estimated values of the source position parameters are obtained by using the closed formula of the gain phase of the modified source steering vector and the source position parameters. The experimental results show that the maximum estimable source number of the proposed algorithm is significantly improved compared with the previous results when only the reference array element has no gainphase error. When the array number is 5 and 9, the maximum estimable source number of the algorithm is 9 and 17, respectively.
- 23 January 2024
- Published by Hindawi Limited in Journal of Sensors
- Vol. 2024, 1-17
Open AccessA High Degree of Freedom Radiation Near-Field Source Localization Algorithm with Gain–Phase Error
The limitation of the number of estimable sources in the localization of radiation near-field sources with gainphase error is examined in this paper. When only the reference element has no gainphase error, a new method based on an accurate model is proposed to enhance the maximum number of estimable sources. Based on the location parameter details of the auxiliary source, the method first derives the gainphase error estimate matrix. Second, the source steering vector including errors is estimated using the total least square estimating signal parameter via rotational invariance techniques (TLS-ESPRIT), and the time-shifted data matrix is built utilizing the spacetime combination idea, thus increasing the degree of freedom of the array. Then, the source steering vector containing the error is modified by the error compensation matrix constructed according to the moment of gainphase error estimation. Finally, the estimated values of the source position parameters are obtained by using the closed formula of the gain phase of the modified source steering vector and the source position parameters. The experimental results show that the maximum estimable source number of the proposed algorithm is significantly improved compared with the previous results when only the reference array element has no gainphase error. When the array number is 5 and 9, the maximum estimable source number of the algorithm is 9 and 17, respectively.
- 31 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 13 (2) , 328-332
IRS Auxiliary UAV Communications: Channel Modeling and Performance Analysis
In this letter, based on the theory of electromagnetic (EM) wave, an intelligent reflecting surface (IRS) assisted channel model for unmanned aerial vehicle (UAV) communications is proposed. The proposed model reveals the relationship between the received signal power of the IRS and the horizontal rotation angle, the size, and the reflection phases of IRS reflection units. The reflection phases are designed to ensure all signals reflected by IRS are phase aligned, and the theoretical result of the received signal power of IRS assisted link is in direct proportion to the square of the total geometric area of the IRS, which accords with the measurement results obtained in the real outdoor scene. In this letter, the smallest geometric area of the IRS, for which the path loss of the IRS-assisted link is equal to that of the direct link, is investigated. With the increase of the carrier frequency, the smallest geometric area gradually decreases. Finally, we investigate the ergodic sum capacity and obtain the closed-form tight upper bound, which is validated through Monte-Carlo simulation results.
- 31 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 13 (2) , 328-332
IRS Auxiliary UAV Communications: Channel Modeling and Performance Analysis
In this letter, based on the theory of electromagnetic (EM) wave, an intelligent reflecting surface (IRS) assisted channel model for unmanned aerial vehicle (UAV) communications is proposed. The proposed model reveals the relationship between the received signal power of the IRS and the horizontal rotation angle, the size, and the reflection phases of IRS reflection units. The reflection phases are designed to ensure all signals reflected by IRS are phase aligned, and the theoretical result of the received signal power of IRS assisted link is in direct proportion to the square of the total geometric area of the IRS, which accords with the measurement results obtained in the real outdoor scene. In this letter, the smallest geometric area of the IRS, for which the path loss of the IRS-assisted link is equal to that of the direct link, is investigated. With the increase of the carrier frequency, the smallest geometric area gradually decreases. Finally, we investigate the ergodic sum capacity and obtain the closed-form tight upper bound, which is validated through Monte-Carlo simulation results.
- 26 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (21) , 26311-26326
An Improved Gray Wolf Algorithm for Radiation Near-Field Source Localization in Exact Model
Spectral search algorithms are widely used in radiation near-field (RNF) source location because of their high estimation accuracy, but they have disadvantages such as large computation and long running time. To solve this problem, the Fresnel model is mainly adopted in the existing literatures to realize the source location estimation in the algorithm of spectral search. Although the operation time is effectively reduced, there is a mismatch between the Fresnel model and the exact model, resulting in that the existing method is not suitable for the source location under the exact model. In order to shorten the running time of the RNF source spectrum search algorithm under the exact model, an improved Gray Wolf optimal algorithm (IGWO) based on the exact model is proposed to estimate the RNF source position, which guarantee the high precision and shorten the operation time. The algorithm uses the noise subspace fitting method as the cost function and the power function as the convergence factor, which shortens the time required for source location and improves the estimation accuracy of the algorithm. The simulation results show that the IGWO algorithm takes less time and has better estimation accuracy than the existing source location algorithms.
- 26 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (21) , 26311-26326
An Improved Gray Wolf Algorithm for Radiation Near-Field Source Localization in Exact Model
Spectral search algorithms are widely used in radiation near-field (RNF) source location because of their high estimation accuracy, but they have disadvantages such as large computation and long running time. To solve this problem, the Fresnel model is mainly adopted in the existing literatures to realize the source location estimation in the algorithm of spectral search. Although the operation time is effectively reduced, there is a mismatch between the Fresnel model and the exact model, resulting in that the existing method is not suitable for the source location under the exact model. In order to shorten the running time of the RNF source spectrum search algorithm under the exact model, an improved Gray Wolf optimal algorithm (IGWO) based on the exact model is proposed to estimate the RNF source position, which guarantee the high precision and shorten the operation time. The algorithm uses the noise subspace fitting method as the cost function and the power function as the convergence factor, which shortens the time required for source location and improves the estimation accuracy of the algorithm. The simulation results show that the IGWO algorithm takes less time and has better estimation accuracy than the existing source location algorithms.
- 26 March 2023
- Published by Elsevier in Signal Processing
- Vol. 209
An auxiliary source-based near field source localization method with sensor position error
- 26 March 2023
- Published by Elsevier in Signal Processing
- Vol. 209
An auxiliary source-based near field source localization method with sensor position error