Xing Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xing Li has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Geli Zhao
3 shared publications- Kaiwen Xia
State Key Laboratory of Hydraulic Engineering Intelligent Construction and Operation, Tianjin University, Tianjin, China
3 shared publications Ying Xu
3 shared publicationsBangbiao Wu
1 shared publicationBozhi Deng
State Key Laboratory of Coal Mine Disaster Dynamics and Control, Chongqing University, Chongqing, China
1 shared publicationChang-Yi Yu
CCCC First Harbor Engineering Company, Co. Ltd., Tianjin 300461, China
1 shared publication
Latest Publications
- 15 August 2025
- Published by Elsevier in Earth and Planetary Science Letters
- Vol. 669
Scaling in source kinematics of earthquakes with size ranging from Mw -4.6 to Mw 7.8
- 15 August 2025
- Published by Elsevier in Earth and Planetary Science Letters
- Vol. 669
Scaling in source kinematics of earthquakes with size ranging from Mw -4.6 to Mw 7.8
- Open Access
- 27 February 2022
- Published by Wiley in Shock and Vibration
- Vol. 2022, 1-15
Dynamic Mechanical Response, Cracking Behavior, and Stress Intensity Factors of Cement Mortar Specimens with Open and Closed Flaws
Major civil and military infrastructures are usually located in mountainous areas with complex geological structures. When subjected to impact loads caused by operational blasting or seismic activities, the inherent flaws or joints in the hosting rock mass may grow irreversibly and eventually and cause the entire structure to collapse. It is, therefore, desirable to understand the mechanical and cracking behaviors of flawed rock structures under dynamic loads. In this work, the cement mortar is used to make the plate specimens, and two different types of flaws, i.e., the open and the closed (resin-filled) flaws, with different inclination angles from 0° to 90° with respect to the loading direction are prefabricated. The nominal strength, crack initiation, and failure characteristics of the specimens under different loading rates are investigated using the split Hopkinson bar (SHPB) system in conjunction with the digital image correlation (DIC) technique. The results indicate that the dynamic nominal strength of both two types of specimens shows similar loading rate and flaw angle dependency, specifically, monotonically increasing with the increase of the loading rate while increasing first and then decreasing with increasing the flaw inclination angle. The strength of specimens with an open flaw is obviously lower than that of the specimens with a closed flaw at a similar loading rate. Besides, the failure mode of specimens with an open flaw is mainly an X-shaped tensile or tensile-shear mixed form regardless of the flaw inclination, whereas the resin-filled flawed specimens always fail in the form of an atypical X-shaped shear pattern with obvious randomness. Moreover, the stress field around the crack tip is carefully extracted based on the obtained displacement field from DIC analysis; the stress intensity factors at crack initiation onset also show flaw inclination- and loading rate-dependent behavior. The strength, cracking behavior, and stress field around the tip during the dynamic loading are closely related to the friction effect between the flaw surfaces. The findings in this work provide some basic insights into the cracking mechanism of rock with open and closed flaws under dynamic loading conditions.
- 27 February 2022
- Published by Wiley in Shock and Vibration
- Vol. 2022, 1-15
Open AccessDynamic Mechanical Response, Cracking Behavior, and Stress Intensity Factors of Cement Mortar Specimens with Open and Closed Flaws
Major civil and military infrastructures are usually located in mountainous areas with complex geological structures. When subjected to impact loads caused by operational blasting or seismic activities, the inherent flaws or joints in the hosting rock mass may grow irreversibly and eventually and cause the entire structure to collapse. It is, therefore, desirable to understand the mechanical and cracking behaviors of flawed rock structures under dynamic loads. In this work, the cement mortar is used to make the plate specimens, and two different types of flaws, i.e., the open and the closed (resin-filled) flaws, with different inclination angles from 0° to 90° with respect to the loading direction are prefabricated. The nominal strength, crack initiation, and failure characteristics of the specimens under different loading rates are investigated using the split Hopkinson bar (SHPB) system in conjunction with the digital image correlation (DIC) technique. The results indicate that the dynamic nominal strength of both two types of specimens shows similar loading rate and flaw angle dependency, specifically, monotonically increasing with the increase of the loading rate while increasing first and then decreasing with increasing the flaw inclination angle. The strength of specimens with an open flaw is obviously lower than that of the specimens with a closed flaw at a similar loading rate. Besides, the failure mode of specimens with an open flaw is mainly an X-shaped tensile or tensile-shear mixed form regardless of the flaw inclination, whereas the resin-filled flawed specimens always fail in the form of an atypical X-shaped shear pattern with obvious randomness. Moreover, the stress field around the crack tip is carefully extracted based on the obtained displacement field from DIC analysis; the stress intensity factors at crack initiation onset also show flaw inclination- and loading rate-dependent behavior. The strength, cracking behavior, and stress field around the tip during the dynamic loading are closely related to the friction effect between the flaw surfaces. The findings in this work provide some basic insights into the cracking mechanism of rock with open and closed flaws under dynamic loading conditions.
- 20 February 2022
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 55 (4) , 2239-2253
Influence of Notch Geometry on the Rock Fracture Toughness Measurement Using the ISRM Suggested Semi-Circular Bend (SCB) Method
- 20 February 2022
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 55 (4) , 2239-2253
Influence of Notch Geometry on the Rock Fracture Toughness Measurement Using the ISRM Suggested Semi-Circular Bend (SCB) Method
- 5 January 2022
- Published by Springer Nature in Geomechanics and Geophysics for Geo-Energy and Geo-Resources
- Vol. 8 (1) , 1-15
A modified triaxial split Hopkinson pressure bar (SHPB) system for quantifying the dynamic compressive response of porous rocks subjected to coupled hydraulic-mechanical loading
- 5 January 2022
- Published by Springer Nature in Geomechanics and Geophysics for Geo-Energy and Geo-Resources
- Vol. 8 (1) , 1-15
A modified triaxial split Hopkinson pressure bar (SHPB) system for quantifying the dynamic compressive response of porous rocks subjected to coupled hydraulic-mechanical loading
- 10 January 2020
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 53 (5) , 2347-2364
True Triaxial Experimental Study of Disturbed Compound Dynamic Disaster in Deep Underground Coal Mine
- 10 January 2020
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 53 (5) , 2347-2364
True Triaxial Experimental Study of Disturbed Compound Dynamic Disaster in Deep Underground Coal Mine