SSSulistyo Sulistyo

Sulistyo Sulistyo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sulistyo Sulistyo has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Hydraulically Actuated Macrobending Fiber-Optic Load Sensor with Symmetric Deformation for Weigh-In-Motion Applications

    by H. Pratomo, S. Sulistyo, D. Hanto, B. Widiyatmoko, A. Setiono

    Road transportation infrastructure plays a vital role in economic growth, logistics, and regional connectivity. However, the increasing number of freight vehicles operating with loads that exceed t...

  • Open Access

    Fabrication and Testing of Epoxy Resin-Based Composites for Electrical Insulation Material Applications

    by Moh Toni Prasetyo, Sulistyo Sulistyo, Sri Nugroho, Abdul Syakur, Amir Izzani Mohamed

    Electrical insulation materials are a critical component in the design and development of electrical systems, playing a crucial role in ensuring the safe and efficient transmission and distribution of electrical power. The aim of this study is to examine the effect of incorporating rice husk ash and silane on the hydrophobicity, leakage current, and tensile strength properties of composite specimens. This study focused on fabricating composites by varying filler concentrations, using epoxy resin as the matrix. The specimens RTV 10, RTV 20, RTV 30, RTV 40, and RTV 50 utilized a filler composed of rice husk ash and silane, with concentrations of 10%, 20%, 30%, 40%, and 50%, respectively. The obtained samples were subjected to testing for leakage current, tensile strength, and water contact angle (hydrophobicity). The study results indicate that increasing the filler content to 40 wt.% in RTV 40 specimens improves the composite’s tracking time, and hydrophobic properties. RTV 40 specimens demonstrated the longest tracking time and the most favourable hydrophobic characteristics compared to the other specimens. However, when the filler content exceeds 40 wt.%, the water contact angle decreases, leading to higher leakage currents and diminished insulating effectiveness. For the RTV 40 specimen, the measured values were a water contact angle of 92°, a tracking time of 1956 seconds, and a tensile strength of 39.59 N/mm². This study addresses several points of the Sustainable Development Goals (SDGs) by improving material properties (SDG 9), promoting sustainable materials (SDG 12) and improving energy-efficient infrastructure (SDG 7).

  • Open Access

    Improving the permeability characteristic of nickle oxide/yttria stabilized zirconia anode through thermal decomposition of organic porous support as sustainable material for green hydrogen ecosystem

    by Muhammad Faesal Febriandyono, Sulistyo Sulistyo, Mohammad Tauviqirrahman, Rayhan Calista, Reza Abdu Rahman

    Modification of the anode for fuel cell is essential to achieve the effective conversion rate at desired level. It is influenced by the gas distribution during the process. The compact profile of the anode is a direct impact for using sintering as reliable production method, making further...

  • Charge/discharge Profiling of Organic Latent Heat Material Embedded in Polymer Matrix for Heat Energy System

    by Reza Abdu Rahman, Sulistyo Sulistyo, M.S.K.TOny Suryo Utomo, Ilham Febriansyah, Ismail Ismail

    The operational aspect of a latent thermal energy storage (LTES) system is highly dependent on the performance of its latent heat storage material (LHSM). In this work, performance evaluation of the LHSM is conducted using low-density polyethylene (LDPE) and linear LDPE. As an initial assessment, three different organic LHSMs are used for the evaluation. The thermal assessment indicates that the heat of fusion for the LHSM varies between 142.45 J/g and 198.8 J/g. Thermal decomposition demonstrates that the LHSM is suitable for operating a thermal power system under 100 °C. The addition of polymer clearly influences the charge/discharge rate for each LHSM. For example, it has a positive influence on paraffin wax, which increases the charge rate up to 54.4 %. A positive outcome is also observed for palmitic acid, which has the highest charge rate at around 4.4 °C/min. Interestingly, the charge/discharge rate for stearic acid is decreased by the presence of a polymer. It implies that the melting/solidification rate can be decreased, which may be advantageous for passive thermal systems. In general, the addition of LDPE/LLDPE alters the performance of LHSM. It makes the polymer suitable to be taken as a stabilizer for the LHSM.


  • Open Access

    Preliminary Work for Preparation and Characterization of Anode Supported SOFC Based on Nio-YSZ Material Using Pore-Former

    by Muhammad Faesal Febriandyono, Sulistyo Sulistyo, Ajie Muhamad Hertriyanto, Mohammad David Setyawan, Reza Abdu Rahman


  • Open Access

    Electrochemical Process Investigation of Synthesizing Magnesium Oxide from Bittern Solution for Solid Oxide Fuel Cells Sealant

    by Sulistyo Sulistyo, Slamet Saefudin, Sulardjaka Sulardjaka, Reza Abdu Rahman

    Magnesium oxide (MgO) is an essential material for producing solid oxide fuel cells (SOFC) sealant. It can be derived from bittern waste. The common approach uses membrane electrolysis, which requires complex equipment and high energy costs. Alternatively, direct electrolysis can be taken using...

  • Open Access

    Investigation on the effect of operation of solar dryer technology according to the drying characteristic of dried product

    by Reza Abdu Rahman, Sulistyo Sulistyo, Mohamad Said Kartono Tony Suryo Utomo, Kaprian Rizki Gunawan, Ismail Ismail

    The application of solar dryer through greenhouse (GH) model as drying method for crops-based product is extremely important in industrial scale agriculture, especially in developed country. The drying model is considered environmentally friendly since it utilizes solar power as the main drying energy. However, the fundamental operational aspect of the basic GH is less discussed according to the drying mechanism of the dried product. In this work, three small-scale drying model are evaluated: open drying (OD), natural convection GH (NCGH), and forced convection GH (FCGH). The drying product is potato, which can be taken as an essential agricultural product in modern world. The OD model has the lowest mass loss rate which less than 50 % of the water from product can be evaporated. The operation of both GH is satisfactory, resulting more than 60 % moisture evaporation. The drying characteristic indicates the two-step failing rate which makes the mass loss fluctuation from the process. The highest mass loss is observed during the constant rate period around 21 % for FCGH and 18 % for NCGH. In addition, the detailed analysis on the effect of each process is discussed in this work. For example, the presence of hair-like structure and the movement of the pith of dried potato during the process. Also, a higher drying rate from NCGH and FCGH initiate the gelatinization and compartmentalization, resulting a substantial water evaporation of the product. It confirms the important correlation of the drying process and water diffusion mechanism of the dried product. The finding from this study can be taken as a vital reference for improving the operation of GH solar dryer


  • Open Access

    Evaluation of the operational curve for heat storage technology using n-octacosane/low-density as a binding material

    by Reza Abdu Rahman, Sulistyo Sulistyo, Mohamad Said Kartono Tony Suryo Utomo, Robertus Dhimas Dhewangga Putra

    Heat storage technology has a critical role for a number of applications involving renewable thermal energy (such as solar water heater). The application of wax (n-octacosane/OCT) as a medium for storing heat brings many positive influences for the system. However, the operational curve is undesirable for the OCT-based energy storage, which makes it necessary to use a binding material. The present work employed LD-class polymer (LDPE) and linear-LDPE as binding materials for OCT. The mixture is prepared through mechanical hot stirring, which comes into two categories: SOCT1 (OCT/LD) and SOCT2 (OCT/LLD). The assessment through the calorimetry method shows an increment in transition temperature for SOCT with a value of 2.1 °C and 5.5 °C. This contributes to the variation of fusion energy for solid-liquid change for both materials, which amounted to 132.05 J/g (SOCT1) and 113.4 J/g (SOCT2). Another assessment related to its chemical and structural phase demonstrates that SOCT has an identical structure to OCT, indicating that SOCT is mixed physically. At the operational level, SOCT is more optimal than OCT according to the indicator related to charge and discharge duration for energy exchange. SOCT1 demonstrates a short plateau line as the indication of a steady transition between 65.4–67.9 °C, while SOCT2 indicates the average heating rate, which is higher than for single OCT. The heat releasing curve for SOCT1 varies at a lower value between 1.92 °C/min and 0.77 °C/min, while SOCT2 has the lowest variation, which is only 0.17 °C/min. Moreover, the self-insulation for SOCT2 has the lowest rate, which is only 0.3 °C/min. The evaluation and analysis from this work show that SOCT is reliable to increase the operational curve of OCT and can be implemented for thermal systems

  • Open Access

    Experimental evaluation on the power characteristic of direct-photovoltaic charging for thermal storage equipment

    by Reza Abdu Rahman, Sulistyo Sulistyo, Mohamad Said Kartono Tony Suryo Utomo, Dimas Ragil, Budhi Muliawan Suyitno

    Thermal storage is an essential equipment for storing excessive heat, especially for water heating systems. The present work proposes a preliminary study to maximize the operation of thermal storage using photovoltaics as the primary source for charging the heat storage material. The assessment indicates the concept is feasible, where the output power from photovoltaics can be directly converted to heat using a heating element. The power ratio is considerably high (up to 38.6%), resulting in the maximum temperature of the heat absorber material (water) increasing to 43.2 °C. The final assessment using suitable phase transition material shows that steady phase behavior is essential to maximizing the temperature profile of the material. It is achieved using stabilized-hexadecanoic acid, which shows a transient phase transition at a temperature of 54.2 °C, reducing the possibility of heat loss with an average temperature rate of 0.54 °C/min in the discharge stage. This finding proves the proposed concept is applicable, while further improvement can be done to adjust the suitable power output from photovoltaic and storage tank arrangement for the actual system. Despite that, the result is expected to accelerate the utilization of photovoltaics as reliable solar renewable technology.


  • Open Access

    Macrobending loss in fiber optic wrapped on rubber-spring wire structure under static load-pressure

    by H Pratomo, S Sulistyo, D Hanto, M Syahadi, D Bayuwati, I Mulyanto, I R Husdi, S Kartolo, B Widiyatmoko, A Setiono

    This work observes rubber-based frame structures for wide helix-shaped-macrobending fiber optic sensors intended for measuring an object with high load levels. In this fiber sensor, the working principle is to measure the power loss (due to bending) of the light traveled in the employed fiber optic. During the applications, it needs a particular mechanical structure to accommodate a reversible fiber bending in the context of load measurement. In this work, a cylindrical-shaped rubber structure mixed with calcium carbonate compound (CaCO3) is constructed as the fiber bending frame (housing) in which a spring wire is inserted into the structure in the two models, i.e., outer and inner-spring structure. Several investigations of static load pressure reveal the optimum structure design for high load measurement. Using the inner-spring model, a rubber structure with 10wt% CaCO3 exhibits the preferable performance with a sensitivity of 0.15 V/Kg.cm2 and measurement load range until 210 Kg.