Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Elisa García-Menéndez has a total of 110 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Novel interferential light-direction sensor exploiting the wave nature of light for elevation angle sensing

    by Michelle Cedeño Mata, Elisa García Menéndez, Juan J. Jiménez, Sandra Bermejo, Moises Garín

    Sun sensors are widely used in aerospace systems as attitude determination devices, providing accurate measurement of the direction of incident sunlight under stringent constraints on mass, volume, power consumption, and robustness. Conventional light-direction sensors are predominantly based on geometric optics, relying on apertures, slits, or shadow-casting structures to infer the angle of incidence from the irradiance distribution across photodetectors. Although these approaches are mature and widely deployed, they inherently involve trade-offs between angular resolution and field of view (FoV), while also requiring precise alignment and bulky optical structures [1-3].In this work, we present the analysis, design, fabrication, and experimental validation of a novel Interferential Light-Direction Sensor (ILDS) prototype for elevation angle sensing. Unlike conventional approaches, the proposed ILDS exploits the wave nature of light by encoding angular information directly into the spectral domain through the angle-dependent transmittance of a planar interferential filter [4]. The proposed architecture combines an interferential Bragg filter, two coloured absorptive filters, and two coplanar photodiodes in a compact and fully planar configuration, enabling high-resolution light-direction sensing without external optics or moving parts.Figure 1 illustrates the conceptual architecture and operating principle of the ILDS. The sensing mechanism relies on a multilayer interferential filter whose transmittance spectrum exhibits an angle-dependent spectral shift, encoding the direction of incoming light into a unique spectral signature. To detect this variation, the transmitted light is sampled using two coloured filters, each transmitting a different spectral region. The light reaching each channel is converted into electrical signals by two photodiodes (D1 and D2). As the incidence angle changes, the optical power transmitted through each filter varies differently, producing two distinct photocurrent responses. The acquired signals are processed to obtain the angular response of the sensor. To do that, a contrast function is calculated to quantify the differential behaviour between both sensing channels.C(θ)=(D1(θ)−D2(θ))/(D1(θ)+D2(θ))Where D1(θ) and D2(θ) correspond to the processed photocurrents at a given angle θ. This contrast function minimizes the influence of absolute illumination variations and enables the estimation of the incoming light direction from the relative response of both photodiodes.Figure 1: (a) Device structure. (b) Sensing mechanism based on the interaction between the angle-dependent interference filter response and the angle-independent coloured filters.The development of the ILDS began with the identification of the most suitable optical configuration capable of maximising angular sensitivity under Air Mass 0 (AM0) illumination conditions, which is representative of the extra-atmospheric solar spectrum expected in the space environment. To this end, a simulation-driven optimisation process was carried out, systematically evaluating the sensor response for all combinations within a set of 13 commercially available coloured filters, while independently optimising the thin-film interferential filter design for each configuration. The final configuration consists of a 11-layer Al2O3-TiO2-based Bragg filter with a total thickness of 1.03 µm, combined with BG39 and RG715 filters from Schott. Figures 2a, 2c, 2e, and 2g summarise the simulated responses of the coloured and interferential filters, the corresponding photodetector outputs, and the ILDS contrast response. Simulations of the complete optical stack predict an average sensitivity of 0.005 deg−1 over a field of view 0º to 85º. Moreover, the simulated response exhibits strong consistency under both AM0 and flat spectral illumination conditions.To experimentally validate the proposed concept, a prototype was fabricated and characterised under controlled illumination conditions. The interferential filter was fabricated by atomic layer deposition (ALD) through alternating deposition cycles of six TiO2 and five Al2O3 layers at 120 ºC. Optical characterization confirmed that the measured transmittance spectrum closely matched the target design (see Figures 2c and d). In parallel, the spectral responses of the coloured filters were experimentally verified (Figure 2b), showing good agreement with the manufacturer specifications.The complete ILDS prototype was finally assembled and electrically characterised using an experimental setup comprising a solar simulator providing a collimated beam with a planar wavefront and a solar-like spectral distribution, a motorised and monitored goniometer acting as the rotational stage, and dedicated photodiode readout electronics. As shown in Figure 2f, the experimental measurements revealed complementary responses between the both photodiodes and a clear dependence on the incidence angle. The resulting experimental contrast function (Figure 2h) exhibited a quasi-linear behaviour within an angular range between 25º and 50º, coinciding with the maximum sensitivity region of the device. Within this angular range, the experimental sensitivity reached 0.012 deg−1, while the angular precision was estimated at 0.014 deg when considering only electrical noise contributions. Overall, the experimental results demonstrate that the ILDS provides a measurable, monotonic, and robust angular response over a wide FoV, validating the feasibility of the proposed sensing approach.Figure 2: Comparison between simulated and experimental performance.In conclusion, the similarities between the trends revealed by simulations and experimental measurements validates the numerical modelling and confirms the viability of the ILDS concept as a novel wave-optics-based light-direction sensing approach. By combining an...

  • Open Access

    Aerosol Optical Properties and Dust Deposition as observed by MEDA Radiation and Dust Sensor (RDS) at Jezero Crater, Mars

    by Raúl Rodriguez-Veloso, Daniel Toledo, Víctor Apestigue, Ignacio Arruego, Clara Lorenzo-Corvo, Germán M. Martínez, Mark T. Lemmon, Juan J. Jiménez-Martín, Elisa García-Menéndez, Ricardo Hueso, et al.

    Aerosols on Mars are a primary element for studying the interaction between the solar radiation and the atmosphere and surface. Depending on properties such as aerosol number density, particle radius, or refractive index, the aerosols can provide positive or negative radiative feedbacks on the atmospheric dynamics. Previous studies have revealed large temporal and spatial variability in the aerosol optical properties, emphasizing the need for continuous monitoring throughout the day and at multiple locations. To address these measurements, the Radiation and Dust Sensor (RDS) [1] was included as part of the Mars Environmental Dynamics Analyzer (MEDA) [2] payload onboard the Perseverance rover of the Mars 2020 mission. The RDS instrument is composed of two sets of eight photodiodes (RDS-DP) and a sky-pointed camera (RDS-SkyCam). One set, oriented toward the zenith, captures radiation from 190 to 1200 nm, while the other, inclined 20° above the horizon at 45° azimuthal intervals, samples a single wavelength. The analysis of these observations, through a radiative transfer model [3], allows for the retrieval of key aerosol parameters such as aerosol opacity at different wavelengths and particle radius. However, the continuous deposition of dust over the sensors [4], since the beginning of the mission, introduces modifications in their optical response. In particular, the zenith-pointed photodiodes require angular response calibration due to the progressive accumulation of dust on their optical surfaces. Here, we present the calibration approach developed for the mission, essential to ensure the accuracy of aerosol property retrievals and reliable long-term atmospheric monitoring. Figure 1 shows the temporal evolution of the RDS-TOP 7 irradiance change derived from our calibration alongside Matscam-Z opacities [5], highlighting the impact of atmospheric conditions. In addition, we report ongoing radiative transfer retrievals of aerosol (dust and ice) optical properties during the first two years of the Mars 2020 mission. The relationship between vortex population and dust deposition rates will also be discussed.Figure 1. Temporal evolution of the irradiance change measured by MEDA-RDS TOP 7 (blue) of the Mars 2020 mission at Jezero Crater, compared with atmospheric opacity at 630 nm measured by Mastcam-Z (red) over the first two years.References:[1] Apestigue, V., et al. “Radiation and Dust Sensor for Mars Environmental Dynamic AnalyzerOnboard M2020 Rover”. Sensor 22.8 (2022): 2907.[2] Rodriguez-Manfredi, Jose Antonio, et al. “The Mars Enviromental Dynamics Analyzer, MEDA. A suite of enviromental sensors for the Mars 2020 mission.” Space science reviews 217.3 (2021): 1-86.[3] Toledo, D., et al. “Measurement of aerosol optical depth and sub-visual cloud detection using the optical depth sensor (ODS)”. Atmospheric Measurement Techniques 9.2 (2016): 455-467.[4] Vicente-Retortillo, A., et al. “Dust Accumulation and Lifting at the Landing Site of the Mars 2020 Mssion, Jezero Crater, as Observed From MEDA.” Geophysical Research Letters 51 (2024).[5] Lemmon, M. T. Et al. “Dust, sand and winds within an active Martian storm in Jezero crater.” Geophysical Research Letters, 49.17 (2022): 0094-8276.

  • Open Access

    Evidence of an enhanced near-surface ozone layer at tropical latitudes on Mars

    by Daniel Viúdez-Moreiras, Michael D. Smith, Mike Wolff, Megan A. J. Brown, Frank Daerden, María-Paz Zorzano, Víctor Apestigue, Ignacio Arruego, Elisa García, Juan J. Jiménez, et al.

    Ozone plays a key role in both atmospheric and near-surface chemistry, as well as in UV absorption in planetary atmospheres. Here, we report observations of ozone from the surface of another planet, using the ozone detector included in the Mars Environmental Dynamics Analyzer (MEDA) Radiation and Dust Sensor (RDS) aboard NASA’s Mars 2020 mission, complementing previous space-based and ground-based observations from Earth. Measurements were acquired at Jezero Crater, Mars, at midday, retrieving an average ozone column abundance of 3.8 ± 2.3 μm-atm (1σ) around aphelion, which fell below uncertainties in northern summer. The retrieved column abundance is in reasonable agreement with previous space-based and ground-based observations from Earth. The measurements of total ozone column abundance around aphelion from Mars 2020 and other missions, together with vertical profile observations from orbit, indicate that ~90% of the observed ozone is confined below 20 km of altitude, the aphelion layer weakly contributing to the total column abundance. These ozone levels below 20 km are 3 to 4 times higher than those predicted by models, challenging current understanding of atmospheric chemistry and composition in the lower atmosphere of Mars. It may be possible that aerosols are reducing the destruction pathways of ozone and/or that unknown active chemistry in the near-surface atmosphere of Mars is at work. Both cases should strongly modify the oxidizing capacity in the lower atmosphere of Mars from current model predictions.


  • Open Access

    Ozone Detector Based on Ultraviolet Observations on the Martian Surface

    by Daniel Viúdez-Moreiras, Alfonso Saiz-Lopez, Michael D. Smith, Víctor Apestigue, Ignacio Arruego, Elisa García, Juan J. Jiménez, José A. Rodriguez-Manfredi, Daniel Toledo, Mike Wolff, et al.

    Ozone plays a key role in both atmospheric chemistry and UV absorption in planetary atmospheres. On Mars, upper-tropospheric ozone has been widely characterized by space-based instruments. However, surface ozone remains poorly characterized, hindered by the limited sensitivity of orbiters to the lowest scale height of the atmosphere and challenges in delivering payloads to the surface of Mars, which have prevented, to date, the measurement of ozone from the surface of Mars. Systematic measurements from the Martian surface could advance our knowledge of the atmospheric chemistry and habitability potential of this planet. NASA’s Mars 2020 mission includes the first ozone detector deployed on the Martian surface, which is based on discrete photometric observations in the ultraviolet band, a simple technology that could obtain the first insights into total ozone abundance in preparation for more sophisticated measurement techniques. This paper describes the Mars 2020 ozone detector and its retrieval algorithm, including its performance under different sources of uncertainty and the potential application of the retrieval algorithm on other missions, such as NASA’s Mars Science Laboratory. Pre-landing simulations using the UVISMART radiative transfer model suggest that the retrieval is robust and that it can deal with common issues affecting surface operations in Martian missions, although the expected low ozone abundance and instrument uncertainties could challenge its characterization in tropical latitudes of the planet. Other space missions will potentially include sensors of similar technology.


  • Open Access

    Aerosol optical properties observed by MEDA Radiation an Dust Sensor (RDS) at Jezero Crater, Mars

    by Raúl Rodriguez-Veloso, Daniel Toledo, Víctor Apéstigue, Ignacio Arruego, Mark T. Lemmon, Michael D. Smith, Germán Martínez, Álvaro Vicente-Retortillo, Juan J. Jiménez-Martín, Elisa García-Menéndez, et al.

    Aerosols on Mars are a primary elements for studying the interaction between the solar radiation and the atmosphere and surface. Depending on properties such as aerosol number density, particle radius, or refractive index, the impact of the aerosols can provide positive or negative radiative feedbacks on the dynamics of the atmosphere. Previous studies have revealed large temporal and spatial variability in the aerosol optical properties, emphasizing the necessity for continuous monitoring of these properties throughout the day and at multiple locations. To address these measurements, the Radiation and Dust Sensor (RDS) [1] is part of the Mars Environmental Dynamics Analyzer (MEDA) [2] payload onboard of the Mars 2020 rover Perseverance. RDS instrument compromises two sets of 8 photodiodes (RDS-DP) and a camera (RDS-SkyCam). One set of photodiodes is pointed upward, with each one covering a different wavelength range between 190-1200 nm. The other set is pointed sideways, 20 degrees above the horizon, and they are spaced 45 degrees apart in azimuth to sample all directions at a single wavelength. The analysis of these observations with a radiative transfer model [3] (Fig. 1) allow us to fit aerosol parameters such as the aerosol opacity at different wavelengths or the aerosol particle radius. In this work we will discuss some preliminary results for the first 100 sols of Mars 2020 mission.References:[1] Apestigue, V., et al. “Radiation and Dust Sensor for Mars Environmental Dynamic Analyzer Onboard M2020 Rover”. Sensor 22.8 (2022): 2907.[2] Rodriguez-Manfredi, Jose Antonio, et al. “The Mars Enviromental Dynamics Analyzer, MEDA. Asuite of enviromental sensors for the Mars 2020 mission.” Space science reviews 217.3 (2021): 1-86.[3] Toledo, D., et al. “Measurement of aerosol optical depth and sub-visual cloud detection using the optical depth sensor (ODS)”. Atmospheric Measurement Techniques 9.2 (2016): 455-467.

  • Open Access

    Front-End Electronic for Miniaturized LIDAR Signal Conditioning

    by Santiago Andrés Velasco, Joaquín Rivas Abalo, Ignacio Arruego Rodríguez, Gustavo Vázquez Yáñez, Saturnino Montalvo Chacón, Esteban Muñoz García, Alberto Martín Ortega, Juan José Jiménez Martín, Elisa García Menéndez, Alberto Moya Señas

    The Miniaturized LIDAR for MARS Atmospheric Research (MiLi) project falls within the European Union funding program called Horizon Europe [1]. Within this general framework, the project being presented is classified under cluster 4 - Digital, Industry, and Space [2]. The investment in the different projects within this fourth point pursues the idea of global leadership of the European industry in key areas, through the development of competitive and trustworthy technologies. This sets the foundation for a competitive, digital, sustainable, and circular industry that allows for progress and innovation in global societal challenges.The use of LIDAR in characterizing the Earth's atmosphere is widespread. These instruments use laser light to study the size and density of aerosol particles, making it logical to consider this solution to examine Martian aerosols (atmospheric dust and ice clouds). However, such instruments are typically large, heavy, and consume significant amounts of energy, making their use aboard planetary exploration modules a complex challenge. Designing and developing a miniaturized, low-power LIDAR for atmospheric research on Mars, which demonstrates the feasibility of a future characterization mission and increases the TRL level of the new technology developed, are the main objectives of the project [3].One of the key aspects in a LIDAR instrument is the design of the receiver circuit for the emitted laser pulse, as it is responsible for both receiving the signal and carrying out its subsequent processing and transmission. In this project we explore the possibility of capturing the pulses through Si-PMT (Silicon Photomultipliers) known as MPPC (Multi-pixel Photon Counter). The proposed design has a dual functionality, as measurements will not only be taken at the time of laser pulse emission but also when it is off, this will allow for an exact characterization of the so-called dark pulses (electrical signals produced by the photodetectors in the absence of incident light). Understanding and characterizing them is of great importance since they directly affect the sensitivity and precision of the measurements carried out.The design presented is based on an innovative solution that addressed the problem detailed as one of the main objectives: instrument compactness. In this, different signal distribution techniques, gain adaptation, EMI mitigation, as well as transmission of signals obtained from photodetectors over long distances are employed.

  • Open Access

    Optical Calibration procedure and results of the mini-spectrometer from the Solar Irradiance Sensor (SIS) radiometer for the ExoMars’22 mission

    by Elisa García-Menéndez, Miguel González-Guerrero, José Ramón De Mingo Martín, Javier Martínez Oter, Israel Martín Beamonte, Saturnino Montalvo Chacón, Joaquín Rivas Abalo, Felipe Serrano Santos, Ignacio Arruego Rodríguez

    This work presents a new procedure from the optical calibration of the mini-spectrometer installed in the Solar Irradiance Sensor (SIS’22) radiometer of the METEO meteorological stations for the ExoMars 2022 Kazachok lander. The calibration procedure applied over this device is based on the predecessors, the DREAMS-SIS for the Schiaparelli [1] lander in ExoMars’16 and the Radiation and Dust sensor (RDS) for the NASA/JPL Perseverance rover from Mars2020 [2], both payloads were designed and calibrated at INTA Payloads and Space Science Department. Due to these instruments were based on multichannel sensors composed by photodiodes, an additional challenge has been including two miniaturized spectrometers on this current instrument, with one of them covered and working in dark conditions. The optical calibration procedure describes different tests, designed and developed to fully characterize the performance of the mini-spectrometer. This output signal based on an electrical response depends on the amount of incident light, the temperature at which the sensor is measuring, the angle of incidence of the light, and the mean throughput of the detector. In addition, it has been found a spectral dependance with the temperature around 5 nm along the thermal cycle studied, between -145 °C and 50 °C. Results display the performance of the mini-spectrometer in terms of integration time, gain mode and acquisition mode, to measure and study the atmosphere, dust size particles, brightness of the sky, optical depth, etc. depending on the illumination conditions on the surface of Mars. Instrument description The SIS′22 for the lander of the ExoMars′22 mission becomes the latest miniaturized radiometer developed at INTA planned to study the Mars atmospheric properties. The presence of a mini-spectrometer to observe the sky is an improvement compared with the previous radiometers. The use of a lightweight, low-power and, a COTS technology (commercial-of-the-shelf), opens up a large number of possibilities and functionalities, despite the needed of qualify, verify and calibrate the device under mission-specific requirements. This mini-spectrometer has a working wavelength range between 340-780 nm with a field of view mask of 45° pointing to the zenith. According to the manufacturer, the mini-spectrometer has a spectral resolution of 15 nm and it is composed of 256 pixels, in addition, it has been included an internal PT1000 for monitoring the temperature. Moreover, there is another mini-spectrometer inside the SIS, working in dark conditions to obtain the dark signal, allowing to subtract the signal from the uncovered one. Additionally, this device will be used as a monitor of the displacement damage of the system. Optical Calibration Procedure The method for the optical calibration is based on the spectro-radiometric transfer from a standard lamp to a standard detector in well-controlled laboratory conditions. The instrument provides a number of ‘counts’ proportional to the photocurrent. The calibration procedure includes different tests based on the mini-spectrometer main dependances as the thermal offset and dark current effect depending on the temperature, the thermal response (TRF), the spectral dependances, the angular response (ARF) depending on the angle of the incident light and, the main throughput (RSun) of the device, which depends on the irradiance level under normal incidence. The SIS instrument has been calibrated at INTA facilities by using different optical ground support equipment, based on standard light sources as: Solar sun simulators: class A with respect to the spectral distribution, uniformity and temporal stability of irradiance. Specific discrete lamps as Hg-Cd and He-Ne, with similar spectrum emission as the mini-spectrometer under study. Optical neutral calibrated filters, to reduce the optical power irradiance from AM0 to a lower level, F50 and F35, with a transmittance of 50% and 35% respectively. Calibrated spectroradiometer, to measure the absolute irradiance spectrum.  Next Figures summarized the main conditions and set up used in each calibration test. Discussion and Conclusions The calibration procedure described has been an improvement with respect the previous ones due to the spectral nature of the mini-spectrometer analyzed. These properties had involved new corrections to have in mind as: The spectral response: calibrating the obtained spectrum with a Cd-Hg lamp source allowed to compare the pixel position of the spectrum peaks with a known certificated and calibrated spectrum. Spectral TRF: it was needed a correction of the thermal displacement on the position of the pixels because of variations of the diffraction grating. The mathematical model used in the analysis to describe each of the calibration performances has been an achievement due to the residual, precision and accuracy obtained when the experimental data was evaluated: Each equation includes all the operation and acquisition modes, the gain configurations and the integration time values to evaluate all possible scenarios. Thermal offset and ARF were composed by physical equation models. It has been possible to characterize the signal in dark conditions with an uncertainty on full scale less than 1 % under ‘single’ and less than 0.01% in the ‘differential’ modes. The spectral shift has been found around 5 nm for the entire thermal range, between -145º C and 50º C, and has been characterized with an uncertainty less than 2 %. The spectral responsivity has been calibrated with a precision and uncertainty below 0.1 % and 7% respectively. References [1] Jiménez,J.J., J Álvarez,F., Gonzalez-Guerrero,M. et al. Calibration OGSEs for multichannel radiometers for Mars atmosphere studies. CEAS Space J10,127–145(2018).https://doi.org/10.1007/s12567-018-0194-8. [2] Ápestigue,V., Gonzalo,A.,...

  • Open Access

    Calibration of RDS of Mars 2020 and SIS’22 of Exomars 2022 for Mars exploration

    by Elisa García-Menéndez, Francisco Javier Álvarez Ríos, Miguel Gonzalez-Guerrero Bartolomé, Víctor Apástigue Palacios, Jose Ramon De Mingo Martin, Javier Martinez Oter, Israel Martín Beamonte, Saturnino Montalvo Chacon, Joaquín Rivas Abalo, Felipe Serrano Santos, et al.

    Introduction INTA Payloads and Space Science Department is involved in several scientific missions to Mars, developing solar irradiance sensors (SIS), name given for these devices which are multispectral multichannel radiometers for atmosphere studies. Two SIS were manufactured before 2015: MetSIS (a radiometer intended to be launched onboard the for the Mars MetNet Precurssor Penetrator [1]) and the DREAMS-SIS for the ill-fated Shiaparelli lander of the ExoMars’16 mission ([2]-[5]) Two radiometers have been developed recently: the Radiation and Dust Sensor(RDS) for Mars2020 Perseverance ([6]-[7]) and the SIS'22 for Exomars 2022 Kazachok lander [8]. RDS is currently working on Mars [9]-[10]. Either RDS and SIS’22 combine optical detectors which point to the zenith (top channels) and to the horizon, with an elevation of 20 degrees respect to the horizontality, and distributed in the azimuth (lateral channels). Innovation The optical response  can be expressed with the following expression, which accounts for the mathematical model used in their calibration [11] and [13] to [19]: This equation has four parameters: ARF, Angular Response Function. This term represents the influence on the channel response of the angular coordinates of the light source respect to every optical detector TRF, Thermal Response Function. It deals with the effect of the detector temperature in its response to a luminous source R, responsivity or mean throughput of the optical detector in the range between the wavelengths l1 and l2, to which the channel is sensitive. Offset, related to the signal of the photodetectors in dark conditions and to the effects on the conditioning electronics on the signal level. The model works under the assumption that angle, temperature, responsivity are independent variables [11]. Hence, four independent characterizations are run in order to get these four parameters: Offset calibration: In dark conditions, the temperature is swept to cover the entire thermal range. Optical Thermal calibration (TRF): the optical power and the angle of incidence of the light are fixed and only the temperature is made to change. Angular calibration (ARF): the optical power and the temperature are fixed and only the light incidence angle is made to change. Mean throughput measurement (RSun): the optical power lamp is excited in several steps, increasing irradiance from a low level to a high one at room temperature with the light at normal incidence over each optical channel. Some of the changes had to be introduced for RDS and SIS’22 calibrations, as new challenges had to be overcome respect to the requirements imposed on the DREAMS SIS. These additional demands had an important impact on the calibration: Narrower FoVs. The alignment is more critical and a new ARF model was implemented. UV channels: different light sources, with a higher signal in the UV, were used. Some channels were designed to detect only diffuse light: light intensity of the solar simulation had to be reduced drastically for the particular calibration of those channels. Having six and eight lateral channels instead of three entailed a higher complexity in the angular sweep and mean throughput alignment. In the particular case of the RDS, having completed the calibration and field campaigns in representative Martian analogous, the first measurements obtained directly from Mars showed some mismatches with the calibration model. A refinement of the analyses was performed to reduce these discrepancies and to improve the lowest measurable signal level: Corrections were introduced in the offset model in order to reduce the discrepancy between the experimental points and the fitting (the residual) by up to 20 counts at a full scale of 65535 (0.05%). That becomes essential in very low light conditions and certain temperatures. It can be as much as a 50 % of the signal. However, such temperatures have never been reached in RDS and even less at times of low illumination (sunrise or sunset). A spectral correction below 2 % was introduced to calculate the mean responsivity of the sun simulator. This lamp source produces a spectrum which is very similar to that of the sun outside the atmosphere. A correction to fit its radiance to a perfect solar spectrum had not been used before.  The main upgrade comes from the modelization of the ARF, its “blocking zone” and the effects of the dust in Mars. ARF The angular sensor response (ARF) can be divided into 3 regions: the Field of View (FoV), the blocking and the transition regions. The blocking zone was found in early tests to be smaller than 1e-4(1e-2%) and was considered negligible. The ARF model was implemented firstly with a function with two terms and it was valid only for the FoV and the transition regions. Blocking regions were found to be non negligible, so a new term was added to account for the sensitivity of the optical channels in those areas, though the experimental data are limited by the noise of the channels noise, in the order of 3e-4 (3e-2%). Despite this refinement, the retrieval models did not match the observations yet. For this reason, a characterization test of the blocking region was performed using the Flight Spare Model (FSM) in a heliostat. That test showed that the effect of the blocking region i is actually lower than 1e-5 counts, while the data from Mars was showing values in the order of 5e-4 (5e-2%). Finally, a test was performed with the FSM unit to evaluate the effect of the deposited dust. The dust in the RDS structure increased the signal in the blocking zone of the optical channels in several orders of magnitude. Therefore, in order to determine the signal in this areas, it it is necessary to estimate the amount of dust deposited on the unit.  Conclusion Improvements have been introduced in the process and analysis of the calibration of the multichannel radiometers manufactured by INTA for Mars missions....

  • Open Access

    Miniature LIDAR for Mars Exploration

    by Ignacio Arruego, Juan J. Jiménez, Alberto Martín-Ortega, Elisa García, Joaquín Rivas, Isaías Carrasco, Gustavo Vázquez, Carmen Córdoba-Jabonero, Laura Gómez, Daniel Toledo, et al.

    The composition of the Martian atmosphere and its dust content is a key factor for understanding the climate of the Red Planet, which is of vital importance to enable future human exploration. The use of atmospheric LIDARs to characterize densities and sizes of aerosol with a height profile, is commonly used on Earth. However, Earth LIDARs are heavy and very power-demanding, which make them not easily on-boardable for planetary exploration. We propose the development of a compact LIDAR aimed at providing the most precise characterization of the suspended dust and clouds of the atmosphere of Mars to-date, while maintaining very reduced power, mass and volume envelops to facilitate its accommodation in a wide variety of landed assets. Rationale and heritage In the past years, INTA has developed four miniature radiometers for different missions: MetSIS for MetNet Lander [1], DREAMS-SIS for Schiaparelli [2], SIS’20 for Kazachok [3] and RDS for Perseverance [4].  All of them, at different levels depending on their complexity, allow the estimation of the atmospheric optical depth with high time resolution, detection of clouds and estimation of the dust concentration vertical profile. A natural step forward to complement our capabilities, especially for the dust profile and characterization of clouds, is a LIDAR. There is only one LIDAR that has already operated on Mars, on board the Phoenix mission. With a 2-wavelengths configuration at 532 and 1064 nm but without depolarization, it operated in the North Pole of Mars for 90 sols [5]. The laser pulses had a power of 30-40 kW and duration of 10 ns. Total mass was 6 kg and the power consumption 30W. A '2B+1d' LIDAR configuration is proposed here to obtain the Particle Backscatter Coefficient (PBC) at two wavelengths (2B), and the depolarization ratio at one of them (1d). They both are used to obtain three LIDAR parameters relevant for dust and cloud characterization: the particle linear depolarization ratio (PLDR), the lidar ratio (LR), and the colour ratio (CR). The intended range is set around 20 km, depending on the scenario, and depolarization measurement capability shall be incorporated. Key technologies for miniaturization The target mass and power envelop are <4 kg and <15W, respectively. The instrument should be capable of operating at atmospheric temperatures below -100°C to minimize the requirements for its accommodation. Achieving those goals will be a technological challenge, and it will be necessary to use technologies not employed before in this scenario. Several key aspects are identified: Pulsed semiconductor laser diodes are proposed for the transmitter, instead of usual (and bulkier) diode-pumped, Q-switched solid-state lasers. This reduces the emitted energy and in turn requires higher repetition rates to improve the Signal-to-Noise ratio. Silicon Photomultipliers, also known as Multi Pixel Photon Counters, will be used as detectors. They allow lower biasing voltages than other high-gain technologies, while they show some trade-offs such as their so-called "cross talk" noise. Its performance under the applicable thermal and radiation environments must be addressed. The use of new synthesis methods to obtain very low thermal expansion coefficient (CTE) materials (crystalline β- eucryptite) to reduce the thermal requirements related to structure and alignment. To reduce the size of the optics and to mitigate the complexity of the collimation of a semiconductor laser (with large spots and emission apertures), 'free form' optics will be considered in the optical design. From the signal processing point of view, the aim is to design a receiver that autonomously adapts the measurement mode (analogue or pulse counting) and parameters (e.g., variable time intervals for pulse-counting) in real time, providing the best signal quality vs. vertical resolution compromise for each altitude. Feasibility To preliminarily assess the feasibility of this LIDAR to reach a scientifically meaningful range, we have performed several simulations of the expected signal and signal-to-noise ratio using extinction and backscattering profiles representative of different dust conditions on Mars, together with technical data extracted from the datasheets of real pre-selected parts and opto-mechanical parameters values that we consider feasible for a compact instrument as the intended one. Emitted pulses have a power of 600W and a duration of 150ns. We have simulated three different background illumination scenarios: night, twilight, and midmorning, as this is critical from the point of view of the “offset” signal it generates (that must be filtered out) and the noise associated with it. We employed worst-case (high) diffuse radiance values on Mars. Extinction and backscattering coefficients have been extracted from Phoenix LIDAR measurements [6], and background illumination values from RDS measurements in Perseverance. The conclusion is that, with adequate signal processing, we should be capable of reaching 4 km during the day, 6-7 at twilight and 15 at night, for the worst-case scenario. 20 km are feasible in better scenarios. On-going activity and next steps A breadboard prototype of the system is being built at INTA for only one channel (one wavelength; no polarization) based on pre-selected pulsed laser diode and silicon photomultiplier, with standard off-the-shelf optical parts and filters. Preliminary laboratory and outdoor measurements will be done to validate the simulations and confirm the feasibility of reaching a meaningful range with the strict miniaturization constraints. Low-temperature characterization of the emitters and detectors, as well as Displacement Damage tests to assess their robustness to the radiation environment will be done by the end of the year. The electronic design has a large heritage from previous Martian sensors as the ones mentioned above, all of them designed to operate down to...

  • Open Access

    Radiation and Dust Sensor for Mars Environmental Dynamic Analyzer Onboard M2020 Rover

    by Victor Apestigue, Alejandro Gonzalo, Juan J. Jiménez, Justin Boland, Mark Lemmon, Jose R. de Mingo, Elisa García-Menendez, Joaquín Rivas, Joaquín Azcue, Laurent Bastide, et al.

    The Radiation and Dust Sensor is one of six sensors of the Mars Environmental Dynamics Analyzer onboard the Perseverance rover from the Mars 2020 NASA mission. Its primary goal is to characterize the airbone dust in the Mars atmosphere, inferring its concentration, shape and optical properties. Thanks to its geometry, the sensor will be capable of studying dust-lifting processes with a high temporal resolution and high spatial coverage. Thanks to its multiwavelength design, it will characterize the solar spectrum from Mars’ surface. The present work describes the sensor design from the scientific and technical requirements, the qualification processes to demonstrate its endurance on Mars’ surface, the calibration activities to demonstrate its performance, and its validation campaign in a representative Mars analog. As a result of this process, we obtained a very compact sensor, fully digital, with a mass below 1 kg and exceptional power consumption and data budget features.