Bolesław Porankiewicz
Research Subjects
Bolesław Porankiewicz has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Daria Wieczorek
Department of Technology and Instrumental Analysis, Institute of Quality Science, Poznań University of Economics and Business, 61-875 Poznań, Poland
3 shared publications Chiaki Tanaka
Emeritus
2 shared publications- Emilia Klimaszewska
Department of Cosmetology, Faculty of Medical Sciences and Health Sciences, Casimir Pulaski University of Radom, Chrobrego 27, 26-600 Radom, Poland
2 shared publications Grzegorz Wieloch
Department of Wood Technology, Warsav University of Life Science
2 shared publicationsIreneusz Idzikowski
LAB-TECH
2 shared publicationsKarol Jóźwiak
Institute of Aviation
2 shared publications
Latest Publications
- 1 November 2020
- Published by BioResources in BioResources
- Vol. 16 (1) , 1424-1437
Modelling cutting forces using the moduli of elasticity in oak peripheral milling
- 1 November 2020
- Published by BioResources in BioResources
- Vol. 16 (1) , 1424-1437
Modelling cutting forces using the moduli of elasticity in oak peripheral milling
- 1 January 2018
- Published by BioResources in BioResources
- Vol. 13 (2) , 3892-3904
A Theoretical Model for the Increases in Cutting Edge Recessions During Milling of Nine Species of Wood
The high-speed steel (HSS) cutting tool edge recession increase (Delta VB) from milling wood of nine wood species with very different properties were analyzed. Theoretical simulations showed that the synergistic effect of the wood density (D), hard mineral contamination (HMC), and high temperature tribochemical reactions (HTTR), as well as initial edge recessions were important factors that accelerated wearing on the examined cutting edges.
- 1 January 2018
- Published by BioResources in BioResources
- Vol. 13 (2) , 3892-3904
A Theoretical Model for the Increases in Cutting Edge Recessions During Milling of Nine Species of Wood
The high-speed steel (HSS) cutting tool edge recession increase (Delta VB) from milling wood of nine wood species with very different properties were analyzed. Theoretical simulations showed that the synergistic effect of the wood density (D), hard mineral contamination (HMC), and high temperature tribochemical reactions (HTTR), as well as initial edge recessions were important factors that accelerated wearing on the examined cutting edges.
- Open Access
- 3 February 2016
- Published by BioResources in BioResources
- Vol. 11 (2) , 4402-4414
The Combustive Heat of Thirteen Deciduous Wood Species
The heat of combustion relative to the mass, Qm, was evaluated for 13 deciduous wood species, ranging from low to high density. The maximum and minimum values for Qm ranged, respectively, from 19.01 kJ⋅g-1 (Sd = 7 J⋅g-1) to 21.66 kJ⋅g-1 (Sd = 6 J⋅g-1) for Populus tremula and Alnus glutinosa wood. The average value of the Qm for all wood specimens evaluated in the present study was 19.93 kJ⋅g-1 (Sd = 706 J⋅g-1), which is 1.6% higher than the value reported in the literature (Krzysik 1975). A high correlation, R = 0.99, was observed between the volumetric heat of combustion, Qv, and wood density, D0. No correlation was discovered among Qm, D0, the ash content in the wood, ac, as well as the content of the following elements in the ash: calcium (Ca), potassium (K), magnesium (Mg), sodium (Na), silica (Si), aluminum (Al), iron (Fe), copper (Cu), manganese (Mn), sulfur (S), and phosphorus (P).
- 3 February 2016
- Published by BioResources in BioResources
- Vol. 11 (2) , 4402-4414
Open AccessThe Combustive Heat of Thirteen Deciduous Wood Species
The heat of combustion relative to the mass, Qm, was evaluated for 13 deciduous wood species, ranging from low to high density. The maximum and minimum values for Qm ranged, respectively, from 19.01 kJ⋅g-1 (Sd = 7 J⋅g-1) to 21.66 kJ⋅g-1 (Sd = 6 J⋅g-1) for Populus tremula and Alnus glutinosa wood. The average value of the Qm for all wood specimens evaluated in the present study was 19.93 kJ⋅g-1 (Sd = 706 J⋅g-1), which is 1.6% higher than the value reported in the literature (Krzysik 1975). A high correlation, R = 0.99, was observed between the volumetric heat of combustion, Qv, and wood density, D0. No correlation was discovered among Qm, D0, the ash content in the wood, ac, as well as the content of the following elements in the ash: calcium (Ca), potassium (K), magnesium (Mg), sodium (Na), silica (Si), aluminum (Al), iron (Fe), copper (Cu), manganese (Mn), sulfur (S), and phosphorus (P).
- Open Access
- 4 May 2015
- Published by BioResources in BioResources
- Vol. 10 (3) , 5489-5502
An Attempt at Modelling of Cutting Forces in Oak Peripheral Milling
An Attempt at Modelling of Cutting Forces in Oak Peripheral Milling
- 4 May 2015
- Published by BioResources in BioResources
- Vol. 10 (3) , 5489-5502
Open AccessAn Attempt at Modelling of Cutting Forces in Oak Peripheral Milling
An Attempt at Modelling of Cutting Forces in Oak Peripheral Milling
- Open Access
- 31 October 2014
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 73 (1) , 35-41
Specific wear on the rake face made of sintered carbide cutting edge during milling of laminated wood
- 31 October 2014
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 73 (1) , 35-41
Open AccessSpecific wear on the rake face made of sintered carbide cutting edge during milling of laminated wood
- Open Access
- 4 November 2013
- Published by BioResources in BioResources
- Vol. 9 (1) , 4-7
Wood Machining Investigations: Parameters to Consider for Thorough Experimentation
Investigators wanting to study aspects of wood machining face many challenges. The material under investigation is inherently different with respect to its three major axes, and it responds in various ways to local temperature, moisture, and many other variables. Researchers proposing future research projects in this area thus face a critically important task of selecting parameters to include either as variables or as quantities to hold constant. This editorial outlines key parameters and conditions of wood machining that can be considered, depending on the scope of a project.
- 4 November 2013
- Published by BioResources in BioResources
- Vol. 9 (1) , 4-7
Open AccessWood Machining Investigations: Parameters to Consider for Thorough Experimentation
Investigators wanting to study aspects of wood machining face many challenges. The material under investigation is inherently different with respect to its three major axes, and it responds in various ways to local temperature, moisture, and many other variables. Researchers proposing future research projects in this area thus face a critically important task of selecting parameters to include either as variables or as quantities to hold constant. This editorial outlines key parameters and conditions of wood machining that can be considered, depending on the scope of a project.
- 1 September 2012
- Published by ICHB PAS Poznan Supercomputing and Networking Center in Computational Methods in Science and Technology
- Vol. 18 (2)
The Effect of Gas Nitriding on Wear of Drill Bits during Particle Board Drilling
- 1 September 2012
- Published by ICHB PAS Poznan Supercomputing and Networking Center in Computational Methods in Science and Technology
- Vol. 18 (2)
The Effect of Gas Nitriding on Wear of Drill Bits during Particle Board Drilling
- 4 August 2011
- Published by BioResources in BioResources
- Vol. 6 (4)
Main and normal cutting forces by machining wood of Pinus sylvestris
In this work the multi-factor, non-linear dependencies between main (tangential) FC (N) and normal (radial) FN (N) cutting forces and eight machining parameters by sawing simulation of wood of Pinus sylvestris L. were evaluated. The relationships are graphically illustrated and discussed. Evidence of several contradictions was found relative to results from available literature.
- 4 August 2011
- Published by BioResources in BioResources
- Vol. 6 (4)
Main and normal cutting forces by machining wood of Pinus sylvestris
In this work the multi-factor, non-linear dependencies between main (tangential) FC (N) and normal (radial) FN (N) cutting forces and eight machining parameters by sawing simulation of wood of Pinus sylvestris L. were evaluated. The relationships are graphically illustrated and discussed. Evidence of several contradictions was found relative to results from available literature.
- 14 July 2006
- Published by Springer Nature in Wood Science and Technology
- Vol. 40 (8) , 673-682
High-speed steel tool wear during wood cutting in the presence of high-temperature corrosion and mineral contamination
- 14 July 2006
- Published by Springer Nature in Wood Science and Technology
- Vol. 40 (8) , 673-682
High-speed steel tool wear during wood cutting in the presence of high-temperature corrosion and mineral contamination