Ming Fang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ming Fang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Baomin Song
Shagang Group, Anyang Yongxing Special Steel Co., Ltd., Anyang 455113, China
1 shared publication - Ming Lv
School of Metallurgical Engineering Xi'an University of Architecture and Technology Xi'an Shaanxi 710055 China
1 shared publication - Xinliang Lu
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China
1 shared publication - Xintao Li
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China
1 shared publication - Zhaohui Zhang
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China
1 shared publication
Latest Publications
- Open Access
Evolution of Non-Metallic Inclusions in 27SiMn Steel
To study the evolution of non-metallic inclusions in 27SiMn steel, the 27SiMn steel produced using the LD-LF-CCM process was sampled in various stages in a steel factory. The evolutionary behavior of inclusion in various processes was systematically analyzed by scanning electron microscopy (SEM-EDS), and the total oxygen content and nitrogen content in 27SiMn steel were measured at various production steps. On the basis of the calcium treatment for 27SiMn steel, the equilibrium reactions for Ca-Al were calculated according to the thermodynamic equilibrium model. The results showed that the types of inclusions at the start of LF stations are mainly Al2O3-FeO and MnS-Al2O3. Before calcium treatment, the inclusions are mostly calcium aluminate and CaO-MgO-Al2O3. Compared with the process after soft blowing, the number density of inclusions in tundish increased by 77.88%, possibly due to secondary oxidation. From the soft blowing process to the continuous casting round billet, the inclusions translate into spherical CaO-MgO-Al2O3-SiO2, and a large number of CaS were observed. One part of the CaS precipitated separately, the other part was semi-wrapped with the composite inclusions. At the same time, calcium treatment increases the number density, mean diameter, and the area fraction of inclusions. The mass fraction of T.O. (total oxygen content) increased significantly after soft blowing, and the N content increased greatly from station to tundish. The change trend of N content in steel was basically consistent with that of T.O. content. It was necessary to prevent the secondary oxidation of molten steel during calcium treatment and the casting process. When the liquidus temperature of liquid steel is 1873 K, w[Al] = 0.022%, and w[Ca] in steel is controlled between 1.085 × 10−6 and 4.986 × 10−6, the Al2O3 inclusion degeneration effect is good.
Open AccessEvolution of Non-Metallic Inclusions in 27SiMn Steel
To study the evolution of non-metallic inclusions in 27SiMn steel, the 27SiMn steel produced using the LD-LF-CCM process was sampled in various stages in a steel factory. The evolutionary behavior of inclusion in various processes was systematically analyzed by scanning electron microscopy (SEM-EDS), and the total oxygen content and nitrogen content in 27SiMn steel were measured at various production steps. On the basis of the calcium treatment for 27SiMn steel, the equilibrium reactions for Ca-Al were calculated according to the thermodynamic equilibrium model. The results showed that the types of inclusions at the start of LF stations are mainly Al2O3-FeO and MnS-Al2O3. Before calcium treatment, the inclusions are mostly calcium aluminate and CaO-MgO-Al2O3. Compared with the process after soft blowing, the number density of inclusions in tundish increased by 77.88%, possibly due to secondary oxidation. From the soft blowing process to the continuous casting round billet, the inclusions translate into spherical CaO-MgO-Al2O3-SiO2, and a large number of CaS were observed. One part of the CaS precipitated separately, the other part was semi-wrapped with the composite inclusions. At the same time, calcium treatment increases the number density, mean diameter, and the area fraction of inclusions. The mass fraction of T.O. (total oxygen content) increased significantly after soft blowing, and the N content increased greatly from station to tundish. The change trend of N content in steel was basically consistent with that of T.O. content. It was necessary to prevent the secondary oxidation of molten steel during calcium treatment and the casting process. When the liquidus temperature of liquid steel is 1873 K, w[Al] = 0.022%, and w[Ca] in steel is controlled between 1.085 × 10−6 and 4.986 × 10−6, the Al2O3 inclusion degeneration effect is good.