Olanrewaju Seun Adesina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Olanrewaju Seun Adesina has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
A. P. I. Popoola
Department of Chemical and Metallurgical Engineering, Tshwane University of Technology, P. M. B. X680, Pretoria 0001, South Africa
6 shared publicationsOlufemi Oluseun Sanyaolu
Department of Mechanical Engineering, Redeemer’s University, Ede, Nigeria
6 shared publications- Adeolu Adesoji Adediran
Materials and Metallurgical Engineering Department, Federal University Oye-Ekiti, Oye-Ekiti, Nigeria
5 shared publications Babatunde Abiodun Obadele
Chemical, Materials & Metallurgical Engineering, Botswana International University of Science and Technology, Palapye, Botswana
5 shared publications- Adekunle Akanni Adeleke
Department of Mechanical Engineering, Nile University of Nigeria, Abuja, Nigeria
4 shared publications D. T. Oloruntoba
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, Akure, Nigeria
4 shared publications
Latest Publications
- 10 June 2025
- Published by Taylor & Francis in Canadian Metallurgical Quarterly
- Vol. 65 (2) , 1226-1255
Tensile and fracture behaviour of aluminium MMCs with ceramic particles – a review
- 10 June 2025
- Published by Taylor & Francis in Canadian Metallurgical Quarterly
- Vol. 65 (2) , 1226-1255
Tensile and fracture behaviour of aluminium MMCs with ceramic particles – a review
- Open Access
- 17 September 2024
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 10 (4) , 1-14
Morphological Characterization and Tribological Properties of TiCoNi Alloy Coatings on Ti–6Al–4V Alloy via Laser Deposition
The goal of this work is to improve the Ti–6Al–4V alloy's hardness and tribological behavior. Coaxial laser surface cladding was used to develop intermetallic layers of nickel (Ni), cobalt (Co), and titanium (Ti). Laser power of 900 W, beam spot size of 3 mm, powder feed rate of 1.0 g/min, and gas flow rate of 1.2 L/min are the optimized parameters used for laser depositions. The laser scan speeds were adjusted between 0.6 and 1.2 m/min. Investigations were conducted into the effects of powder admixture and laser parameters on the fabricated coatings' microstructure, tribological behavior and hardness. X-ray diffractometry (XRD), energy dispersive spectroscopy (EDS) with Scanning electron microscopy (SEM) was employed for the characterization of the microstructural evolution and phase identification, respectively. Additionally, the tribological experiment was conducted via UMT-2 –CETR reciprocating tribometer, and the coatings’ micro-hardness characteristics were examined using EmcoTEST DURASCAN. The micrographs exhibit no signs of porousness, cracks, or stress introduction, according to the results. For every manufactured sample, good metallurgical adhesion was obtained. By comparing the hardness of the ternary coating (Co–Ni–10Ti deposited at a scan speed of 1.2 m/min, with a hardness of 980 HV) to the substrate (Ti–6Al–4V, with a hardness of 330 HV), a hardness increase of approximately 2.96 times was observed. Furthermore, the Co–Ni–10Ti coating, deposited at a scan speed of 1.2 m/min, demonstrated a 51.1% reduction in the coefficient of friction (COF) compared to the base alloy, indicating superior anti-wear performance. The enhanced properties are attributed to the formation of hard intermetallic compounds such as Ti–Co, Co2Ti, Al5Co2, and Ni3Ti, along with their uniform distribution and finely tuned grain sizes.
- 17 September 2024
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 10 (4) , 1-14
Open AccessMorphological Characterization and Tribological Properties of TiCoNi Alloy Coatings on Ti–6Al–4V Alloy via Laser Deposition
The goal of this work is to improve the Ti–6Al–4V alloy's hardness and tribological behavior. Coaxial laser surface cladding was used to develop intermetallic layers of nickel (Ni), cobalt (Co), and titanium (Ti). Laser power of 900 W, beam spot size of 3 mm, powder feed rate of 1.0 g/min, and gas flow rate of 1.2 L/min are the optimized parameters used for laser depositions. The laser scan speeds were adjusted between 0.6 and 1.2 m/min. Investigations were conducted into the effects of powder admixture and laser parameters on the fabricated coatings' microstructure, tribological behavior and hardness. X-ray diffractometry (XRD), energy dispersive spectroscopy (EDS) with Scanning electron microscopy (SEM) was employed for the characterization of the microstructural evolution and phase identification, respectively. Additionally, the tribological experiment was conducted via UMT-2 –CETR reciprocating tribometer, and the coatings’ micro-hardness characteristics were examined using EmcoTEST DURASCAN. The micrographs exhibit no signs of porousness, cracks, or stress introduction, according to the results. For every manufactured sample, good metallurgical adhesion was obtained. By comparing the hardness of the ternary coating (Co–Ni–10Ti deposited at a scan speed of 1.2 m/min, with a hardness of 980 HV) to the substrate (Ti–6Al–4V, with a hardness of 330 HV), a hardness increase of approximately 2.96 times was observed. Furthermore, the Co–Ni–10Ti coating, deposited at a scan speed of 1.2 m/min, demonstrated a 51.1% reduction in the coefficient of friction (COF) compared to the base alloy, indicating superior anti-wear performance. The enhanced properties are attributed to the formation of hard intermetallic compounds such as Ti–Co, Co2Ti, Al5Co2, and Ni3Ti, along with their uniform distribution and finely tuned grain sizes.
- Open Access
- 6 September 2024
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 10 (4) , 1-14
Surface Modification and Corrosion Performance of Laser Cladded Co–Ni on Ti–6Al–4 V in 0.5 M H2SO4 Environment
This study investigates the laser cladding of Co and Ni powders onto Ti–6Al–4 V substrates, varying the admixed percentages while adjusting laser processing parameters. The influence of nickel and cobalt contents on the microstructure, phase composition, and electrochemical behavior of the laser-clad Ti–6Al–4 V coatings were analyzed. Coating morphology and phases were characterized using scanning electron microscopy (SEM) equipped with energy dispersive spectrometry (EDS), and X-ray diffractometry (XRD), respectively. The corrosion resistance of Ti–6Al–4 V, both with and without Ni–Co additions, in 0.5 M H2SO4 was evaluated using potentiodynamic polarization technique. Results indicated that the coatings exhibited excellent metallurgical compatibility with the substrate. Additionally, the high scan speed laser-clad samples showed enhanced corrosion resistance compared to those processed at low speeds. The potentiodynamic polarization analysis revealed passive behavior in all specimens, with higher cobalt content notably enhancing passivity and corrosion resistance by suppressing the anodic reaction.
- 6 September 2024
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 10 (4) , 1-14
Open AccessSurface Modification and Corrosion Performance of Laser Cladded Co–Ni on Ti–6Al–4 V in 0.5 M H2SO4 Environment
This study investigates the laser cladding of Co and Ni powders onto Ti–6Al–4 V substrates, varying the admixed percentages while adjusting laser processing parameters. The influence of nickel and cobalt contents on the microstructure, phase composition, and electrochemical behavior of the laser-clad Ti–6Al–4 V coatings were analyzed. Coating morphology and phases were characterized using scanning electron microscopy (SEM) equipped with energy dispersive spectrometry (EDS), and X-ray diffractometry (XRD), respectively. The corrosion resistance of Ti–6Al–4 V, both with and without Ni–Co additions, in 0.5 M H2SO4 was evaluated using potentiodynamic polarization technique. Results indicated that the coatings exhibited excellent metallurgical compatibility with the substrate. Additionally, the high scan speed laser-clad samples showed enhanced corrosion resistance compared to those processed at low speeds. The potentiodynamic polarization analysis revealed passive behavior in all specimens, with higher cobalt content notably enhancing passivity and corrosion resistance by suppressing the anodic reaction.
- 13 May 2024
- Published by Springer Nature in Chemistry Africa
- Vol. 7 (7) , 1-14
Development of Aluminium Base Anode for Cathodic Protection of Steel
- 13 May 2024
- Published by Springer Nature in Chemistry Africa
- Vol. 7 (7) , 1-14
Development of Aluminium Base Anode for Cathodic Protection of Steel
- Open Access
- 7 May 2024
- Published by Springer Nature in Emergent Materials
- Vol. 7 (5) , 2117-2128
Effect of SiC addition on laser-based CoNi binary alloy coatings on Ti-6Al-4V alloy
This research explores the impact of variations in laser scanning speed and the incorporation levels of SiC-Ni-Co powders on Ti-6Al-4V alloy using laser surface cladding technique. Key parameters, including a consistent laser power of 700 W, a 4 mm beam spot size, a powder feed rate of 1.0 g/min, and a gas flow rate of 3 L/min, along with fixed powder compositions, were maintained. The laser scanning speeds were adjusted to 0.4 m/min, 0.8 m/min, and 1.2 m/min. Microstructural analyses were carried out using scanning electron microscopy (SEM) while Vickers microhardness was employed to assess coating hardness, and corrosion properties were evaluated using a linear potentiodynamic polarization technique. Following the corrosion attack, the protective oxides formed were identified through SEM and X-ray diffractometer (XRD). The results revealed a strong metallurgical relationship between the clad layer and the substrate, demonstrating the effectiveness of the laser-clad technique. Particularly, the highest laser scan speed exhibited the most significant improvements in hardness and corrosion resistance. The coatings displayed an average hardness value of 1269.20 HV0.1, a notable fourfold increase compared to the substrate's value of 334 HV0.1. Concerning corrosion, a clear correlation emerged between scan speed and polarization resistance, confirming that higher scan speeds could lead to enhanced polarization resistance.
- 7 May 2024
- Published by Springer Nature in Emergent Materials
- Vol. 7 (5) , 2117-2128
Open AccessEffect of SiC addition on laser-based CoNi binary alloy coatings on Ti-6Al-4V alloy
This research explores the impact of variations in laser scanning speed and the incorporation levels of SiC-Ni-Co powders on Ti-6Al-4V alloy using laser surface cladding technique. Key parameters, including a consistent laser power of 700 W, a 4 mm beam spot size, a powder feed rate of 1.0 g/min, and a gas flow rate of 3 L/min, along with fixed powder compositions, were maintained. The laser scanning speeds were adjusted to 0.4 m/min, 0.8 m/min, and 1.2 m/min. Microstructural analyses were carried out using scanning electron microscopy (SEM) while Vickers microhardness was employed to assess coating hardness, and corrosion properties were evaluated using a linear potentiodynamic polarization technique. Following the corrosion attack, the protective oxides formed were identified through SEM and X-ray diffractometer (XRD). The results revealed a strong metallurgical relationship between the clad layer and the substrate, demonstrating the effectiveness of the laser-clad technique. Particularly, the highest laser scan speed exhibited the most significant improvements in hardness and corrosion resistance. The coatings displayed an average hardness value of 1269.20 HV0.1, a notable fourfold increase compared to the substrate's value of 334 HV0.1. Concerning corrosion, a clear correlation emerged between scan speed and polarization resistance, confirming that higher scan speeds could lead to enhanced polarization resistance.
- 26 December 2023
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 11 (2) , 233-245
Numerical Modelling and Optimization of the Surface Qualities of Laser Cladded Ti-6Al-4V Alloy
- 26 December 2023
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 11 (2) , 233-245
Numerical Modelling and Optimization of the Surface Qualities of Laser Cladded Ti-6Al-4V Alloy
- Open Access
- 3 April 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-14
Statistical modeling of Si-based refractory compounds of bamboo leaf and alumina reinforced Al–Si–Mg alloy hybrid composites
Wear properties of Al–Mg–Si alloy matrix hybrid composites made with Si-based refractory compounds (SBRC) derived from bamboo leaf ash (BLA) as complimentary reinforcement with alumina have been studied. The experimental result indicate that optimum wear loss was obtained at higher sliding speed. The wear rate of the composites increased with an increase in BLA wt. %, with the composites having 4%SBRC from BLA + 6% alumina (B4) showing the least wear loss for the different sliding speeds and wear loads considered. With increasing BLA weight percent, the composites' wear mechanism was mostly abrasive wear. Numerical optimization results using central composite design (CCD) reveal that at a wear load of 587.014N, sliding speed of 310.053 rpm and B4 hybrid filler composition level respectively, minimum responses in wear rate (0.572mm2/min), specific wear rate (0.212cm2/g.cm3) and wear loss (0.120 g) would be obtained for the developed AA6063 based hybrid composite. Perturbation plots indicate that the sliding speed have more impact on wear loss, while wear load have significant impact on the wear rate and specific wear rate.
- 3 April 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-14
Open AccessStatistical modeling of Si-based refractory compounds of bamboo leaf and alumina reinforced Al–Si–Mg alloy hybrid composites
Wear properties of Al–Mg–Si alloy matrix hybrid composites made with Si-based refractory compounds (SBRC) derived from bamboo leaf ash (BLA) as complimentary reinforcement with alumina have been studied. The experimental result indicate that optimum wear loss was obtained at higher sliding speed. The wear rate of the composites increased with an increase in BLA wt. %, with the composites having 4%SBRC from BLA + 6% alumina (B4) showing the least wear loss for the different sliding speeds and wear loads considered. With increasing BLA weight percent, the composites' wear mechanism was mostly abrasive wear. Numerical optimization results using central composite design (CCD) reveal that at a wear load of 587.014N, sliding speed of 310.053 rpm and B4 hybrid filler composition level respectively, minimum responses in wear rate (0.572mm2/min), specific wear rate (0.212cm2/g.cm3) and wear loss (0.120 g) would be obtained for the developed AA6063 based hybrid composite. Perturbation plots indicate that the sliding speed have more impact on wear loss, while wear load have significant impact on the wear rate and specific wear rate.
- Open Access
- 29 September 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (10) , 286
Electrochemical Studies of the Corrosion Behavior of Al/SiC/PKSA Hybrid Composites in 3.5% NaCl Solution
The corrosion behavior of metal matrix composites (MMCs) is accelerated by the inclusion of reinforcements. Hence, this study investigates the corrosion behavior of MMCs produced from Al 6063 matrix alloy with reinforcement particulates of silicon carbide (SiC) and palm kernel shell ash (PKSA) inclusion at different mix ratios. The MMCs were synthesized using the double stir casting technique. The corrosion behaviors of the composites in NaCl solutions were studied via gravimetric analysis and electrochemical measurements. The gravimetric analysis showed fluctuating dissolution rate of the samples in NaCl solution to indicate flawed film as well as corrosion product formation over the surface of the specimens. The observed corrosion mechanism of the samples was general and pitting corrosion. The presence of reinforcements within the Al6063 matrix acted as active sites for corrosion initiation. The range of values for Ecorr and Icorr obtained in 3.5% NaCl at 24 h was between −220.62 and −899.46 mV and between 5.45 and 40.87 µA/cm2, respectively, while at 72 h, the Ecorr values ranged from 255.88 to −887.28 mV, and the Icorr ranged from 7.19 to 16.85 µA/cm2. The Nyquist and Bode plots revealed the electrochemical corrosion behavior of the samples under investigation, with predominant reactions on the surface of the samples linked to charge transfer processes. The relative resistance to corrosion of the samples depends on the thin oxide film formed on the surface of the samples.
- 29 September 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (10) , 286
Open AccessElectrochemical Studies of the Corrosion Behavior of Al/SiC/PKSA Hybrid Composites in 3.5% NaCl Solution
The corrosion behavior of metal matrix composites (MMCs) is accelerated by the inclusion of reinforcements. Hence, this study investigates the corrosion behavior of MMCs produced from Al 6063 matrix alloy with reinforcement particulates of silicon carbide (SiC) and palm kernel shell ash (PKSA) inclusion at different mix ratios. The MMCs were synthesized using the double stir casting technique. The corrosion behaviors of the composites in NaCl solutions were studied via gravimetric analysis and electrochemical measurements. The gravimetric analysis showed fluctuating dissolution rate of the samples in NaCl solution to indicate flawed film as well as corrosion product formation over the surface of the specimens. The observed corrosion mechanism of the samples was general and pitting corrosion. The presence of reinforcements within the Al6063 matrix acted as active sites for corrosion initiation. The range of values for Ecorr and Icorr obtained in 3.5% NaCl at 24 h was between −220.62 and −899.46 mV and between 5.45 and 40.87 µA/cm2, respectively, while at 72 h, the Ecorr values ranged from 255.88 to −887.28 mV, and the Icorr ranged from 7.19 to 16.85 µA/cm2. The Nyquist and Bode plots revealed the electrochemical corrosion behavior of the samples under investigation, with predominant reactions on the surface of the samples linked to charge transfer processes. The relative resistance to corrosion of the samples depends on the thin oxide film formed on the surface of the samples.
- 15 August 2022
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 29 (10)
ELECTRODEPOSITION OF NICKEL ON HEAT-TREATED LOW CARBON STEEL FOR YAM POUNDING BEATER
This work focused on the mechanical and corrosion behaviors of electroplated nickel on heat-treated low carbon steel serving as an alternative to austenitic stainless steel for the yam beater in a yam pounding machine. Four standard samples were prepared for electrodeposition from the steel samples by heating to a temperature of 920°C with a 60-min holding time. One of the samples was air-cooled while the remaining three were quenched in H2O and later tempered at 450°C, 550°C and 650°C for 60[ ]min. After the heat treatment process, the ultimate tensile strength, toughness, and microhardness of the samples were obtained. Nickel electrodeposition was later carried out on the heat-treated mild steel using Watt standard bath concentration. Optical Microscopy (OM) and Scanning Electron Microscope equipped with energy dispersion spectroscopy (SEM/EDS) were used for the characterization of the heat-treated and nickel-electrodeposited samples. More so, the electrochemical behavior of the nickel-plated samples was studied in a yam fluid environment using the potentiodynamic polarization technique. X-ray fluorescence (XRF) was used to analyze the chemical and oxide composition of the samples. The results showed that among all the heat treatment operations, the sample heat-treated at 920°C and tempered at the highest tempering temperature of 650°C gave the highest toughness value (102[ ]MJ/m3) when compared with stainless steel at 124[ ]MJ/m3. The sample heat-treated at 920°C and tempered at 550°C displayed a corrosion rate of 0.022182[ ]mm/yr as against the stainless steel sample with a value of 0.0031864[ ]mm/yr. From the analysis, the nickel deposited on the heat-treated samples enhanced corrosion resistance in the yam fluid. XRF analysis of the yam before pounding, after processing with nickel electroplated, and stainless beaters shows the content of nickel as 0.0941%, 0.109%, and 0.1113%, respectively. It was concluded that the materials for the yam pounding beater, therefore, perform better if they were both heat-treated and nickel-plated. Invariably, stainless steel could be successfully replaced with heat-treated and nickel-plated mild steel for use as a yam pounding beater.
- 15 August 2022
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 29 (10)
ELECTRODEPOSITION OF NICKEL ON HEAT-TREATED LOW CARBON STEEL FOR YAM POUNDING BEATER
This work focused on the mechanical and corrosion behaviors of electroplated nickel on heat-treated low carbon steel serving as an alternative to austenitic stainless steel for the yam beater in a yam pounding machine. Four standard samples were prepared for electrodeposition from the steel samples by heating to a temperature of 920°C with a 60-min holding time. One of the samples was air-cooled while the remaining three were quenched in H2O and later tempered at 450°C, 550°C and 650°C for 60[ ]min. After the heat treatment process, the ultimate tensile strength, toughness, and microhardness of the samples were obtained. Nickel electrodeposition was later carried out on the heat-treated mild steel using Watt standard bath concentration. Optical Microscopy (OM) and Scanning Electron Microscope equipped with energy dispersion spectroscopy (SEM/EDS) were used for the characterization of the heat-treated and nickel-electrodeposited samples. More so, the electrochemical behavior of the nickel-plated samples was studied in a yam fluid environment using the potentiodynamic polarization technique. X-ray fluorescence (XRF) was used to analyze the chemical and oxide composition of the samples. The results showed that among all the heat treatment operations, the sample heat-treated at 920°C and tempered at the highest tempering temperature of 650°C gave the highest toughness value (102[ ]MJ/m3) when compared with stainless steel at 124[ ]MJ/m3. The sample heat-treated at 920°C and tempered at 550°C displayed a corrosion rate of 0.022182[ ]mm/yr as against the stainless steel sample with a value of 0.0031864[ ]mm/yr. From the analysis, the nickel deposited on the heat-treated samples enhanced corrosion resistance in the yam fluid. XRF analysis of the yam before pounding, after processing with nickel electroplated, and stainless beaters shows the content of nickel as 0.0941%, 0.109%, and 0.1113%, respectively. It was concluded that the materials for the yam pounding beater, therefore, perform better if they were both heat-treated and nickel-plated. Invariably, stainless steel could be successfully replaced with heat-treated and nickel-plated mild steel for use as a yam pounding beater.