Nicolae Constantin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nicolae Constantin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alexandru Paraschiv
Romanian Research and Development Institute for Gas Turbines COMOTI, 220D Iuliu Maniu Av., 061126 Bucharest, Romania
1 shared publication - Andreea Udrea
Automatic Control and Systems Engineering Department, Faculty of Automatic Control and Computers, National University of Science and Technology Politehnica of Bucharest, Splaiul Independentei, No. 313, 060042 Bucharest, Romania
1 shared publication - Constantin Florin Caruntu
Department of Automatic Control and Applied Informatics, Gheorghe Asachi Technical University of Iasi, 700050 Iasi, Romania
1 shared publication - Gheorghe Matache
Special Components for Gas Turbines Department, Romanian Research and Development Institute for Gas Turbines COMOTI, 220D Iuliu Maniu, 061126 Bucharest, Romania
1 shared publication - Ioan Stefan Sacala
Automatic Control and Systems Engineering Department, Faculty of Automatic Control and Computers, National University of Science and Technology Politehnica of Bucharest, Splaiul Independentei, No. 313, 060042 Bucharest, Romania
1 shared publication - Ioana-Miruna Vlasceanu
Automatic Control and Systems Engineering Department, Faculty of Automatic Control and Computers, National University of Science and Technology Politehnica of Bucharest, Splaiul Independentei, No. 313, 060042 Bucharest, Romania
1 shared publication
Latest Publications
- Open Access
- 9 July 2025
- Published by MDPI AG in Electronics
- Vol. 14 (14) , 2759
Comparative Evaluation of Fuzzy Logic and Q-Learning for Adaptive Urban Traffic Signal Control
In recent years, the number of vehicles in cities has visibly increased, leading to continuous modifications in general mobility. Pollution levels and congestion cases are reaching higher numbers as well, pointing to a need for better optimization solutions. Several existing control systems still rely on fixed timings for traffic lights, lacking an adaptive approach that can adjust the timers depending on real-time conditions. This study aims to provide a design for such a tool, by implementing two different approaches: Fuzzy Logic Optimization and an Adaptive Traffic Management strategy. The first controller involves Fuzzy Logic based on rule-based that adjust green and red-light timings depending on the number of vehicles at an intersection. The second model provides traffic adjustments based on external equipment such as road sensors and cameras, offering dynamic solutions tailored to current traffic conditions. Both methods are tested in a simulated environment using SUMO (Simulation of Urban Mobility). They were evaluated according to key efficiency indicators, namely average waiting time, lost time per cycle, number of stops per intersection, and overall traffic fluidity. Results demonstrate that Q-learning maintains consistent waiting times between 2.57 and 3.71 s across all traffic densities while achieving Traffic Flow Index values above 85%, significantly outperforming Fuzzy Logic, which shows greater variability and lower efficiency under high-density conditions.
- 9 July 2025
- Published by MDPI AG in Electronics
- Vol. 14 (14) , 2759
Open AccessComparative Evaluation of Fuzzy Logic and Q-Learning for Adaptive Urban Traffic Signal Control
In recent years, the number of vehicles in cities has visibly increased, leading to continuous modifications in general mobility. Pollution levels and congestion cases are reaching higher numbers as well, pointing to a need for better optimization solutions. Several existing control systems still rely on fixed timings for traffic lights, lacking an adaptive approach that can adjust the timers depending on real-time conditions. This study aims to provide a design for such a tool, by implementing two different approaches: Fuzzy Logic Optimization and an Adaptive Traffic Management strategy. The first controller involves Fuzzy Logic based on rule-based that adjust green and red-light timings depending on the number of vehicles at an intersection. The second model provides traffic adjustments based on external equipment such as road sensors and cameras, offering dynamic solutions tailored to current traffic conditions. Both methods are tested in a simulated environment using SUMO (Simulation of Urban Mobility). They were evaluated according to key efficiency indicators, namely average waiting time, lost time per cycle, number of stops per intersection, and overall traffic fluidity. Results demonstrate that Q-learning maintains consistent waiting times between 2.57 and 3.71 s across all traffic densities while achieving Traffic Flow Index values above 85%, significantly outperforming Fuzzy Logic, which shows greater variability and lower efficiency under high-density conditions.
- Open Access
Investigation of Scanning Strategies and Laser Remelting Effects on Top Surface Deformation of Additively Manufactured IN 625
The main drawbacks of the Laser Powder Bed Fusion (LPBF) process are the surface quality and dimensional accuracy of manufactured parts due to the edge and corner effects. These effects can be diminished by using an appropriate balance of the process parameters and scanning strategies. This paper focuses on the assessment of reducing the edge and corner effects that occur in additively manufactured IN 625 alloy via the LPBF technique by varying the hatch angle rotation (by 45°, 67°, and 90°) and volumetric energy density (VED), and using the laser top surface remelting technique (LSR). The edge and corner effects of the cubic samples were quantitatively evaluated on the top surface by 3D laser surface scanning. It was found that the edge and corner effects became more pronounced in the cases of samples built with no contour and hatch angles of 45° and 67°, while the smallest deformations were obtained when the hatch angle was rotated by 90°. Moreover, the heights of both the edge and corner ridges increase as the number of remeltings passing the top layer increases. Conversely, when a lower VED was used for melting the top layer(s) of the samples, the edge and corner ridges were slightly reduced.
Open AccessInvestigation of Scanning Strategies and Laser Remelting Effects on Top Surface Deformation of Additively Manufactured IN 625
The main drawbacks of the Laser Powder Bed Fusion (LPBF) process are the surface quality and dimensional accuracy of manufactured parts due to the edge and corner effects. These effects can be diminished by using an appropriate balance of the process parameters and scanning strategies. This paper focuses on the assessment of reducing the edge and corner effects that occur in additively manufactured IN 625 alloy via the LPBF technique by varying the hatch angle rotation (by 45°, 67°, and 90°) and volumetric energy density (VED), and using the laser top surface remelting technique (LSR). The edge and corner effects of the cubic samples were quantitatively evaluated on the top surface by 3D laser surface scanning. It was found that the edge and corner effects became more pronounced in the cases of samples built with no contour and hatch angles of 45° and 67°, while the smallest deformations were obtained when the hatch angle was rotated by 90°. Moreover, the heights of both the edge and corner ridges increase as the number of remeltings passing the top layer increases. Conversely, when a lower VED was used for melting the top layer(s) of the samples, the edge and corner ridges were slightly reduced.