MYMing Yan

Ming Yan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ming Yan has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Radiation Tolerant Multi-Loop VCO Structures in 28-nm FDSOI Technology

    by Jaime Cardenas Chavez, Ming Yan, Adriana Noguera Cundar, Xiaotong Lu, Tejinder Sandhu, Kamal El-Sankary, Li Chen

    This manuscript investigates the use of different multi-loop voltage-controlled oscillator (VCO) structures to mitigate single event effects (SEE). The first approach is a three-stage fully differential cross-coupled ring oscillator, designed with current regulation biasing to enhance supply noise rejection. The second is a fully differential current-mode logic (CML) multi-path ring oscillator with coarse/fine control. Both structures were fabricated in 28-nm FDSOI technology. The cross-coupled ring VCO exhibits enhanced performance when using the high-current configuration, showing a phase noise of -80.1 dBc/Hz at 1 MHz offset from the center frequency of 1.49 GHz and a figure of merit (FoM) of 140. Moreover, the CML multi-path VCO stands out as a high-performance structure with -93.4 dBc/Hz phase noise measured at 1 MHz offset from the 1.42 GHz carrier frequency and a FoM of 151. Single event effects (SEE) and total ionizing dose (TID) responses were evaluated using a 105 MeV proton beam and 60Co radiation, respectively. Experimental results demonstrated significant single event transient (SET) mitigation with both solutions, with the CML multi-path VCO exhibiting superior radiation tolerance with a maximum single event frequency transient (SEFT) of 4.2% and a maximum recovery time of 1.3 ns. Both designs showed high TID tolerance up to 300 krads.

  • A 10-bit 50-MS/s Radiation Tolerant Split Coarse/Fine SAR ADC in 65-nm CMOS

    by Ming Yan, Jaime Cardenas Chavez, Kamal El-Sankary, Li Chen, Xiaotong Lu

    This article presents a 10-bit radiation-hardened-by-design (RHBD) SAR analog-to-digital converter (ADC) operating at 50 MS/s, designed for aerospace applications in high-radiation environments. The system- and circuit-level redundancy techniques are implemented to mitigate radiation-induced errors and metastability. A novel split coarse/fine asynchronous SAR ADC architecture is proposed to provide system-level redundancy. At circuits level, single-event effects (SEEs) error detection and radiation-hardened techniques are implemented. Our co-designed SEE error detection scheme includes last-bit-cycle (LBC) detection following the LSB cycle and metastability detection (MD) via a ramp generator with a threshold trigger. This approach detects and corrects radiation-induced errors using a coarse/fine redundant algorithm. The radiation-hardened latch comparators and D flip-flops (DFFs) are incorporated to further mitigate SEEs. The prototype design is fabricated using TSMC 65-nm technology, with an ADC core area of 0.0875 mm2 and a power consumption of 2.79 mW at a 1.2-V power supply. Postirradiation tests confirm functionality up to 100-krad(Si) total ionizing dose (TID) and demonstrate over 90% suppression of large SEE under laser testing.


  • Open Access

    Study on Single Event Transients in Amplifier for Switched-Capacitor Circuits in CMOS Technology

    by Ming Yan, Jaime Cardenas Chavez, Adriana Noguera Cundar, Kamal El-Sankary, Li Chen

    This article presents a comprehensive analysis of the sensitivity of different switched-capacitor amplifier circuits to Single Event Transients (SETs). SETs are temporary variations in circuit output voltage or current caused by the interaction of heavy ions or high-energy protons with sensitive device nodes. The study focuses on three types of amplifier circuits commonly used in Multiplying Digital-to-Analog Converter (MDAC) stages of state-of-the-art pipelined ADCs: operational amplifier (Op-Amp) MDACs, comparator-based switched-capacitor (CBSC) MDACs, and ring amplifier (RAMP) based MDACs. By employing a TCAD-calibrated double exponential transient current pulse model, we simulate the SET responses resulting from heavy ion strike experiments on sensitive nodes of each MDAC type. Our analysis and simulations reveal the amplitude and recovery time of the output results for each MDAC type when subjected to SETs. Notably, we propose a novel radiation hardening solution: the parallel-auxiliary ring amplifier (PA-RAMP) structure, which demonstrates significantly better tolerance to SETs compared to other designs. This research not only contributes to the understanding of SET effects on analog switched-capacitor amplifier circuits but also introduces a cost-effective approach to mitigate these effects. As technology nodes scale down and circuits become more susceptible to SETs, the PA-RAMP structure offers a promising solution for radiation-hardened applications, enabling the use of scaling-friendly RAMPs with enhanced tolerance to SETs.


  • A PVT Compensated Resistance to Frequency Converter for Sensor Array Read-Out

    by Ming Yan, Dalton Martini Colombo, Michael S. Freund, Kamal El-Sankary

    This paper presents a PVT (process, voltage, temperature) compensated CMOS resistor to frequency read-out circuit for resistive sensing applications. Resistive sensing is used in different applications, such as olfactory sensing. An accurate read-out circuit is needed to detect the resistance values for onchip sensor arrays. Existing techniques suffer from PVT variations and require a large silicon chip area. The proposed design offers a simple, accurate, PVT insensitive sensor read-out circuit where a closed-loop configuration, a switched capacitor resistor, operational amplifier integrator, and a voltage-controlled oscillator are used. The design is implemented and fabricated using TSMC 180 nm CMOS technology. The value for the measured sensor’s resistance ranges between 10k and 100MΩ with an accuracy of 0.1% while the chip area is 0.0455mm2 with 98.1μW power consumption. Also, the settling time for the step resistance change is about 2 μs.