Hao Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hao Xu has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Tiezhi Sun
School of Naval Architecture and Ocean Engineering, Dalian University of Technology 4 , Dalian 116081
14 shared publications - Guiyong Zhang
State Key Laboratory of Structural Analysis, Optimization and CAE Software for Industrial Equipment, School of Naval Architecture Engineering, Dalian University of Technology 1 , Dalian 116024
6 shared publications - Jinxiong Duan
Dalian University of Technology, China
5 shared publications - Shaoqian Zhang4 shared publications
- Song Zhang
State Key Laboratory of Structural Analysis, Optimization and CAE Software for Industrial Equipment, School of Naval Architecture, Dalian 116024, China
3 shared publications Zhikun Cai
3 shared publications
Latest Publications
- 27 October 2026
- Published by Elsevier in Ocean Engineering
- Vol. 369
Coupled dynamics of the gas-liquid interface and shock-wave system in underwater supersonic gas jets
- 27 October 2026
- Published by Elsevier in Ocean Engineering
- Vol. 369
Coupled dynamics of the gas-liquid interface and shock-wave system in underwater supersonic gas jets
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Effect of surface protrusions on the formation and evolution of ventilated attached cavities over a curved wall
Large-eddy simulations coupled with the Schnerr–Sauer cavitation model were performed in a simplified curved-wall configuration to investigate ventilated cavity formation downstream of a surface protrusion. The numerical method was validated against water-tunnel data, reproducing the observed cavity morphology and predicting mean wall pressures with relative errors of approximately of 2%–13%. The results show that, in the absence of the protrusion, the near-wall gas undergoes only transient attachment, downstream convection, and shedding, and fails to develop into a persistent attached cavity over the simulated interval. In contrast, the protrusion generates a coupled low-pressure, low-velocity, and recirculating region downstream, which promotes the sustained accumulation of the initial gas cluster and the ventilated gas, thereby enabling the formation of a persistent attached cavity over the simulated interval. The ventilation-hole position strongly affected cavity development: the attached-cavity volume increased from 2.10 × 10−2 m3 at D = 0.3 m to a maximum of 2.36 × 10−2 m3 at D = 0.4 m (four times the protrusion height), and then decreased to 1.19 × 10−2 m3 at D = 0.7 m. These findings demonstrate that a properly placed protrusion and ventilation hole can reorganize the local wake to enhance gas entrainment, confinement, and replenishment, providing a practical route for cavitation control over curved leeward surfaces.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Effect of surface protrusions on the formation and evolution of ventilated attached cavities over a curved wall
Large-eddy simulations coupled with the Schnerr–Sauer cavitation model were performed in a simplified curved-wall configuration to investigate ventilated cavity formation downstream of a surface protrusion. The numerical method was validated against water-tunnel data, reproducing the observed cavity morphology and predicting mean wall pressures with relative errors of approximately of 2%–13%. The results show that, in the absence of the protrusion, the near-wall gas undergoes only transient attachment, downstream convection, and shedding, and fails to develop into a persistent attached cavity over the simulated interval. In contrast, the protrusion generates a coupled low-pressure, low-velocity, and recirculating region downstream, which promotes the sustained accumulation of the initial gas cluster and the ventilated gas, thereby enabling the formation of a persistent attached cavity over the simulated interval. The ventilation-hole position strongly affected cavity development: the attached-cavity volume increased from 2.10 × 10−2 m3 at D = 0.3 m to a maximum of 2.36 × 10−2 m3 at D = 0.4 m (four times the protrusion height), and then decreased to 1.19 × 10−2 m3 at D = 0.7 m. These findings demonstrate that a properly placed protrusion and ventilation hole can reorganize the local wake to enhance gas entrainment, confinement, and replenishment, providing a practical route for cavitation control over curved leeward surfaces.
- 17 April 2026
- Published by Elsevier in Ocean Engineering
- Vol. 357
Experimental study on the multiphase-flow characteristics of a deflected supersonic submerged jet under co-flow conditions
- 17 April 2026
- Published by Elsevier in Ocean Engineering
- Vol. 357
Experimental study on the multiphase-flow characteristics of a deflected supersonic submerged jet under co-flow conditions
- Open Access
- 8 December 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (12) , 2331
Unsteady Flow and Loading Characteristics of Rotating Spheres During Underwater Ejection
This study systematically investigates the evolution of the flow field and cavitation behavior during the underwater launch of a rotating sphere. By comparing surface pressure distribution, cavitation evolution, flow separation locations, and re-entrant jet formation under various rotational conditions, this study reveals the significant influence of rotation on both the cavitation processes and sphere’s motion trajectory. It is found that under rotational conditions, cavity detachment tends to occur earlier on the front side, and the re-entrant jet develops more fully, reaching maximum length and intensity at a moderate angular velocity. In additionally, rotation alters the cavity interface and overall flow structure, resulting in noticeable differences in surface wetting, pressure distribution, and separation behavior between the front and rear sides. As the rotational speed increases, flow separation points become less distinct, and pressure fluctuations on the rear side intensify, indicating that rotation plays a critical role in modulating underwater cavitation dynamics. The findings provide theoretical insights into flow control and cavitation risk assessment for underwater launches of rotating bodies.
- 8 December 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (12) , 2331
Open AccessUnsteady Flow and Loading Characteristics of Rotating Spheres During Underwater Ejection
This study systematically investigates the evolution of the flow field and cavitation behavior during the underwater launch of a rotating sphere. By comparing surface pressure distribution, cavitation evolution, flow separation locations, and re-entrant jet formation under various rotational conditions, this study reveals the significant influence of rotation on both the cavitation processes and sphere’s motion trajectory. It is found that under rotational conditions, cavity detachment tends to occur earlier on the front side, and the re-entrant jet develops more fully, reaching maximum length and intensity at a moderate angular velocity. In additionally, rotation alters the cavity interface and overall flow structure, resulting in noticeable differences in surface wetting, pressure distribution, and separation behavior between the front and rear sides. As the rotational speed increases, flow separation points become less distinct, and pressure fluctuations on the rear side intensify, indicating that rotation plays a critical role in modulating underwater cavitation dynamics. The findings provide theoretical insights into flow control and cavitation risk assessment for underwater launches of rotating bodies.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Shoulder-attached cavity dynamics and hydrodynamic characteristics of underwater vehicles
When an underwater vehicle rapidly exits the storage tube, the residual gas near the tube mouth forms an attached cavity around the shoulder of the vehicle. This cavity significantly influences the motion stability and hydrodynamic loading of the vehicle. In this study, numerical simulations were conducted to investigate the formation mechanism of the attached cavity and to evaluate the effects of various head shapes on the evolution of the transient flow field and the hydrodynamic performance of the vehicle. The results indicate that flow separation at the shoulder initiates the development of the attached cavity. The subsequent shedding of the cavity induces a periodic hairpin vortex and strong pressure fluctuations. As the shoulder geometry becomes more streamlined, the gas volume within the cavity decreases, the asymmetry becomes more pronounced, and the cavity shedding mode changes. The dominant shedding frequency tends to increase, while the amplitude diminishes, indicating a transition toward a more unstable flow state, with an intermediate configuration likely exhibiting a transitional regime in which multiscale shedding coexists. This complex evolution of the cavity directly affects the overall hydrodynamic loading characteristics of the vehicle. This study offers a significant reference point for the prediction of multiphase cavitating flows and the design of motion stability of underwater vehicles.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Shoulder-attached cavity dynamics and hydrodynamic characteristics of underwater vehicles
When an underwater vehicle rapidly exits the storage tube, the residual gas near the tube mouth forms an attached cavity around the shoulder of the vehicle. This cavity significantly influences the motion stability and hydrodynamic loading of the vehicle. In this study, numerical simulations were conducted to investigate the formation mechanism of the attached cavity and to evaluate the effects of various head shapes on the evolution of the transient flow field and the hydrodynamic performance of the vehicle. The results indicate that flow separation at the shoulder initiates the development of the attached cavity. The subsequent shedding of the cavity induces a periodic hairpin vortex and strong pressure fluctuations. As the shoulder geometry becomes more streamlined, the gas volume within the cavity decreases, the asymmetry becomes more pronounced, and the cavity shedding mode changes. The dominant shedding frequency tends to increase, while the amplitude diminishes, indicating a transition toward a more unstable flow state, with an intermediate configuration likely exhibiting a transitional regime in which multiscale shedding coexists. This complex evolution of the cavity directly affects the overall hydrodynamic loading characteristics of the vehicle. This study offers a significant reference point for the prediction of multiphase cavitating flows and the design of motion stability of underwater vehicles.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Flow and thrust vectoring characteristics of underwater high-speed gas jet
When utilizing high-speed gas jet for the propulsion of underwater vehicles, complex flow phenomena such as ventilated cavitation, bubble expansion, and contraction are formed, along with corresponding complex thrust characteristics. In this paper, an experimental study was conducted on the thrust and flow field evolution characteristics of vector-deflected high-speed gas jets produced by a Laval nozzle under co-flow conditions. Under the experimental conditions of this study, the venting position of the pulsating foam tail cavity shifts with the increase in the nozzle vector angle θ. The axial component of thrust exhibits a noticeable loss as the vector angle θ increases, and its oscillation is correlated with the pressure pulsation of the tail cavity. The nozzle thrust vector angle operates within an optimal range, with the lateral force peaking at θ = 6°. Beyond this angle, the lateral force diminishes as θ progresses further. The amplitude of the lateral force is related to the vent channel, with unobstructed channels corresponding to the peak values of the lateral force. This paper can provide a reference for the design of vector jet propulsion systems for underwater vehicles. The unique phenomena and patterns of underwater vector jets revealed through experiments lay the foundation and offer insights for more in-depth mechanistic studies.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Flow and thrust vectoring characteristics of underwater high-speed gas jet
When utilizing high-speed gas jet for the propulsion of underwater vehicles, complex flow phenomena such as ventilated cavitation, bubble expansion, and contraction are formed, along with corresponding complex thrust characteristics. In this paper, an experimental study was conducted on the thrust and flow field evolution characteristics of vector-deflected high-speed gas jets produced by a Laval nozzle under co-flow conditions. Under the experimental conditions of this study, the venting position of the pulsating foam tail cavity shifts with the increase in the nozzle vector angle θ. The axial component of thrust exhibits a noticeable loss as the vector angle θ increases, and its oscillation is correlated with the pressure pulsation of the tail cavity. The nozzle thrust vector angle operates within an optimal range, with the lateral force peaking at θ = 6°. Beyond this angle, the lateral force diminishes as θ progresses further. The amplitude of the lateral force is related to the vent channel, with unobstructed channels corresponding to the peak values of the lateral force. This paper can provide a reference for the design of vector jet propulsion systems for underwater vehicles. The unique phenomena and patterns of underwater vector jets revealed through experiments lay the foundation and offer insights for more in-depth mechanistic studies.
- 16 July 2024
- Published by Elsevier in Ocean Engineering
- Vol. 310
Experimental investigation on flow characteristics and instability of submerged high-speed gaseous jets under co-flow
- 16 July 2024
- Published by Elsevier in Ocean Engineering
- Vol. 310
Experimental investigation on flow characteristics and instability of submerged high-speed gaseous jets under co-flow
- 16 April 2024
- Published by Elsevier in Ocean Engineering
- Vol. 304
A joint experimental study of the flow evolution and thrust characteristics of underwater supersonic gas jets
- 16 April 2024
- Published by Elsevier in Ocean Engineering
- Vol. 304
A joint experimental study of the flow evolution and thrust characteristics of underwater supersonic gas jets