Shaojuan Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shaojuan Wang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Hao Zhang
Key Laboratory of Rubber-Plastics, Qingdao University of Science & Technology, Qingdao, China
3 shared publications Hai-Peng Li
Key Laboratory of Rubber-Plastics, Qingdao University of Science & Technology, Qingdao, China
1 shared publicationHaipeng Li
Key Laboratory of Rubber-Plastics, Qingdao University of Science & Technology, Qingdao 266042, China
1 shared publicationHan-Qi Zhu
Key Laboratory of Rubber-Plastics, Qingdao University of Science & Technology, Qingdao, China
1 shared publicationJia-Meng Liang
Key Laboratory of Rubber-Plastics, Qingdao University of Science & Technology, Qingdao, China
1 shared publicationJiameng Liang
Key Laboratory of Rubber-Plastics, Qingdao University of Science & Technology, Qingdao 266042, China
1 shared publication
Latest Publications
- 24 November 2025
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (48) , 7927-7934
Polymorphism in poly(vinylidene fluoride) nanoparticles prepared by a precipitation method: roles of the stirring rate, temperature and molecular weight
PVDF nanoparticles are prepared by the precipitation method (2000 rpm, 0 °C, 180 kDa), achieving 74.6% β-phase and 88.1% electroactive phase content. Crystallinity increases with temperature and stirring rate but is less affected by molecular weight.
- 24 November 2025
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (48) , 7927-7934
Polymorphism in poly(vinylidene fluoride) nanoparticles prepared by a precipitation method: roles of the stirring rate, temperature and molecular weight
PVDF nanoparticles are prepared by the precipitation method (2000 rpm, 0 °C, 180 kDa), achieving 74.6% β-phase and 88.1% electroactive phase content. Crystallinity increases with temperature and stirring rate but is less affected by molecular weight.
- 12 June 2025
- Published by Springer Nature in Chinese Journal of Polymer Science
- Vol. 43 (8) , 1406-1414
Influence of β-Phase Content on the Stretching-induced α-β Phase Transition of Highly Oriented Poly(vinylidene fluoride) Ultrathin Films
- 12 June 2025
- Published by Springer Nature in Chinese Journal of Polymer Science
- Vol. 43 (8) , 1406-1414
Influence of β-Phase Content on the Stretching-induced α-β Phase Transition of Highly Oriented Poly(vinylidene fluoride) Ultrathin Films
- Open Access
Effect of 3-Mercaptopropyltriethoxysilane Modified Illite on the Reinforcement of SBR
To achieve the sustainable development of the rubber industry, the substitute of carbon black, the most widely used but non-renewable filler produced from petroleum, has been considered one of the most effective ways. The naturally occurring illite with higher aspect ratio can be easily obtained in large amounts at lower cost and with lower energy consumption. Therefore, the expansion of its application in advanced materials is of great significance. To explore their potential use as an additive for reinforcing rubber, styrene butadiene rubber (SBR) composites with illites of different size with and without 3-mercaptopropyltriethoxysilane (KH580) modification were studied. It was found that the modification of illite by KH580 increases the K-illite/SBR interaction, and thus improves the dispersion of K-illite in the SBR matrix. The better dispersion of smaller size K-illite with stronger interfacial interaction improves the mechanical properties of SBR remarkably, by an increment of about nine times the tensile strength and more than ten times the modulus. These results demonstrate, except for the evident effect of particle size, the great importance of filler–rubber interaction on the performance of SBR composites. This may be of great significance for the potential wide use of the abundant naturally occurring illite as substitute filler for the rubber industry.
Open AccessEffect of 3-Mercaptopropyltriethoxysilane Modified Illite on the Reinforcement of SBR
To achieve the sustainable development of the rubber industry, the substitute of carbon black, the most widely used but non-renewable filler produced from petroleum, has been considered one of the most effective ways. The naturally occurring illite with higher aspect ratio can be easily obtained in large amounts at lower cost and with lower energy consumption. Therefore, the expansion of its application in advanced materials is of great significance. To explore their potential use as an additive for reinforcing rubber, styrene butadiene rubber (SBR) composites with illites of different size with and without 3-mercaptopropyltriethoxysilane (KH580) modification were studied. It was found that the modification of illite by KH580 increases the K-illite/SBR interaction, and thus improves the dispersion of K-illite in the SBR matrix. The better dispersion of smaller size K-illite with stronger interfacial interaction improves the mechanical properties of SBR remarkably, by an increment of about nine times the tensile strength and more than ten times the modulus. These results demonstrate, except for the evident effect of particle size, the great importance of filler–rubber interaction on the performance of SBR composites. This may be of great significance for the potential wide use of the abundant naturally occurring illite as substitute filler for the rubber industry.