Sanghyun Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sanghyun Park has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Sungyoon Lee
HIL LAB, Inc. 2 , Pohang 37554
3 shared publications - Tae Jun Yu
Handong Global Univ, Dept Adv Convergence, Pohang 37554, South Korea
3 shared publications - Geonhui Lee
HIL Lab. Inc
2 shared publications - Seungjin Hwang
HIL Lab. Inc
2 shared publications - Daewoong Park
Department of Advanced Convergence, Handong Global University 1 , Pohang 37554, Republic of Korea
1 shared publication - Duckbong Seo
SUN Engineering, Inc. 3 , Gwangju 61009
1 shared publication
Latest Publications
- 1 November 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
Through-thickness cutting of 110-mm-thick SUS304–SS400 clad plates using a 6-kW laser oxy-fuel and oxy-flame hybrid process
This study examined through-thickness cutting of 110-mm-thick SUS304–SS400 clad steel (10 mm SUS304/100 mm SS400) using a 6-kW laser oxy-fuel and oxy-flame hybrid (LOXAFH) process. With SUS304 facing the cutting head, oxy-fuel heating formed no measurable entrance kerf. Three laser-assisted oxygen cutting (LASOX) trials failed to penetrate at 6 kW, 0.70 MPa(g) cutting-oxygen pressure, 50 mm min−1, and 10 mm standoff distance. At the same principal settings, one LOXAFH trial achieved full penetration with an O2–liquefied petroleum gas flame and approximately 30 s of stationary preheating. Two additional LOXAFH trials produced through cuts at selected settings. Across these three cuts, top and bottom kerf widths were 6.80–7.75 and 9.55–10.38 mm, respectively. At otherwise nominally identical LOXAFH settings, one 6-kW trial penetrated, whereas eight 3-kW trials failed. At 3 kW, three SS400-up trials penetrated, while eight SUS304-up trials failed. These comparisons indicate that laser power and incident material affected penetration. The matched LASOX–LOXAFH comparison supports feasibility, but the effects of stationary preheating and continuous flame assistance could not be separated. Improved oxygen access remains a possible explanation because in-kerf flow and cut-front motion were not measured. Repeatable penetration was observed at selected conditions, but repeatability at a fixed successful setting for the standard SUS304-up plate remains unverified. Comprehensive cut-quality assessment and suitability for nuclear dismantling require further evaluation.
- 1 November 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
Through-thickness cutting of 110-mm-thick SUS304–SS400 clad plates using a 6-kW laser oxy-fuel and oxy-flame hybrid process
This study examined through-thickness cutting of 110-mm-thick SUS304–SS400 clad steel (10 mm SUS304/100 mm SS400) using a 6-kW laser oxy-fuel and oxy-flame hybrid (LOXAFH) process. With SUS304 facing the cutting head, oxy-fuel heating formed no measurable entrance kerf. Three laser-assisted oxygen cutting (LASOX) trials failed to penetrate at 6 kW, 0.70 MPa(g) cutting-oxygen pressure, 50 mm min−1, and 10 mm standoff distance. At the same principal settings, one LOXAFH trial achieved full penetration with an O2–liquefied petroleum gas flame and approximately 30 s of stationary preheating. Two additional LOXAFH trials produced through cuts at selected settings. Across these three cuts, top and bottom kerf widths were 6.80–7.75 and 9.55–10.38 mm, respectively. At otherwise nominally identical LOXAFH settings, one 6-kW trial penetrated, whereas eight 3-kW trials failed. At 3 kW, three SS400-up trials penetrated, while eight SUS304-up trials failed. These comparisons indicate that laser power and incident material affected penetration. The matched LASOX–LOXAFH comparison supports feasibility, but the effects of stationary preheating and continuous flame assistance could not be separated. Improved oxygen access remains a possible explanation because in-kerf flow and cut-front motion were not measured. Repeatable penetration was observed at selected conditions, but repeatability at a fixed successful setting for the standard SUS304-up plate remains unverified. Comprehensive cut-quality assessment and suitability for nuclear dismantling require further evaluation.
- Open Access
- 23 April 2024
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 178
Real-time monitoring system for 100 mJ laser shock peening
- 23 April 2024
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 178
Open AccessReal-time monitoring system for 100 mJ laser shock peening
- Open Access
- 30 April 2022
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 40 (2) , 156-164
Study of the Change in Surface Wettability for Zircaloy-4 Utilizing Spatially Homogenized Nanosecond Laser Beam
This study introduces laser surface modification technology using a 532 nm Nd:YAG nanosecond laser. A laser beam homogenizer was used to spatially homogenize the laser beam into a square shape with an interference pattern of 30 μm. For laser surface modification processing, primary processing under 110 conditions was first performed, and then, 15 types of main processing conditions were determined based on the three-dimensional surface structure of laser surface modified zircaloy-4. Subsequently, the specimen was post-processed using three methods: left in the air (25 ℃), heated in the oven (200 ℃ for 2 h), and boiled in water (100 ℃ for 2 h). In the absence of post-processing or with heat post-processing, the laser surface modified zircaloy-4 showed super hydrophobicity with a contact angle of 150° or higher for specific laser surface processing parameters. Under specific laser surface processing conditions, the laser surface modified zircaloy-4 with boiling water post-processing exhibited properties close to super hydrophilic with a contact angle of less than 5°. It was confirmed that the surface wettability of zircaloy-4 can be controlled using a spatially shaped nanosecond laser beam.
- 30 April 2022
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 40 (2) , 156-164
Open AccessStudy of the Change in Surface Wettability for Zircaloy-4 Utilizing Spatially Homogenized Nanosecond Laser Beam
This study introduces laser surface modification technology using a 532 nm Nd:YAG nanosecond laser. A laser beam homogenizer was used to spatially homogenize the laser beam into a square shape with an interference pattern of 30 μm. For laser surface modification processing, primary processing under 110 conditions was first performed, and then, 15 types of main processing conditions were determined based on the three-dimensional surface structure of laser surface modified zircaloy-4. Subsequently, the specimen was post-processed using three methods: left in the air (25 ℃), heated in the oven (200 ℃ for 2 h), and boiled in water (100 ℃ for 2 h). In the absence of post-processing or with heat post-processing, the laser surface modified zircaloy-4 showed super hydrophobicity with a contact angle of 150° or higher for specific laser surface processing parameters. Under specific laser surface processing conditions, the laser surface modified zircaloy-4 with boiling water post-processing exhibited properties close to super hydrophilic with a contact angle of less than 5°. It was confirmed that the surface wettability of zircaloy-4 can be controlled using a spatially shaped nanosecond laser beam.