Marko Miloš
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Marko Miloš has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Nenad Kolarević
Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia
5 shared publications - Nikola Davidović
Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia
5 shared publications - Miloš Stanković
University of Belgrade
3 shared publications - Aleksandar Dimić
Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia
1 shared publication Branislav Jojić
1 shared publication- Dimitrije Manić
University of Belgrade
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 53 (4) , 585-594
Development of an expendable turbojet engine for the propulsion of an unmanned aerial vehicle
This paper presents preliminary engineering methodology for the design of expendable turbojets in the range of 400 daN thrust. This class of engines are among biggest used for missiles, typical applications are Harpoon or Storm Shadow missiles and variety of target drones. The term "expendable" dictates different philosophy in design: simple, reliable and cheap are higher demands than performances. The objective was to analyze concepts of design and development employed in existing engines and according to this to present methodology of design followed with numerical example. Moreover, the aim was to show how to transform design in real construction of such engine followed with engineering considerations and logic conclusions.The main contribution of this work is that defines and explains steps required to design expendable turbojet engine, combining scientific and engineering approaches.
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 53 (4) , 585-594
Open AccessDevelopment of an expendable turbojet engine for the propulsion of an unmanned aerial vehicle
This paper presents preliminary engineering methodology for the design of expendable turbojets in the range of 400 daN thrust. This class of engines are among biggest used for missiles, typical applications are Harpoon or Storm Shadow missiles and variety of target drones. The term "expendable" dictates different philosophy in design: simple, reliable and cheap are higher demands than performances. The objective was to analyze concepts of design and development employed in existing engines and according to this to present methodology of design followed with numerical example. Moreover, the aim was to show how to transform design in real construction of such engine followed with engineering considerations and logic conclusions.The main contribution of this work is that defines and explains steps required to design expendable turbojet engine, combining scientific and engineering approaches.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 83-86
INITIAL EXPENDABLE TURBOJET PROTOTYPE TESTING EXPIRIENCES
Expendable turbojets, typically in thrust range from 40 to 400 daN, are used in target drones and missiles. Because of their usage they are designed to be simple and cheap rather to have some challenged performances according to [1],[2] and [3]. Also, because of their applications they are not requiring rigorous certifications as turbojets for man applications. Usually they are certificated together with the system in which they are installed. This paper is presenting experiences with initial prototype testing. At the moment when designed engine is produced and when some of component or subsystem testing are finished, we have to start with the very first tests. The point is that we will have to check performance of the engine which has to be running for the first time. If everything is fine during the first test and the results are very similar to expecting values it will be perfect. But usually in the engineering world it will not be the case. More than this we have to solve many small issues until we can run the prototype engine with confidence. On the other hand these days time for development is very limited, it is expected that such engine is ready for serial production in 12 to 18 months and consequently it is very important to accurately understand possible problems during initial testing. If we make wrong conclusions it will delay assigned development time and possibly come in position that development went to wrong direction. Technical papers usually describe achieved results but without complete picture of problem which they have to overcome in order to achieve development goals. With such motivation the material discussed at this paper describes what had to done to make prototype engine to run correctly and refers to the turbojet engine TJE-200 at the EDePro company.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 83-86
INITIAL EXPENDABLE TURBOJET PROTOTYPE TESTING EXPIRIENCES
Expendable turbojets, typically in thrust range from 40 to 400 daN, are used in target drones and missiles. Because of their usage they are designed to be simple and cheap rather to have some challenged performances according to [1],[2] and [3]. Also, because of their applications they are not requiring rigorous certifications as turbojets for man applications. Usually they are certificated together with the system in which they are installed. This paper is presenting experiences with initial prototype testing. At the moment when designed engine is produced and when some of component or subsystem testing are finished, we have to start with the very first tests. The point is that we will have to check performance of the engine which has to be running for the first time. If everything is fine during the first test and the results are very similar to expecting values it will be perfect. But usually in the engineering world it will not be the case. More than this we have to solve many small issues until we can run the prototype engine with confidence. On the other hand these days time for development is very limited, it is expected that such engine is ready for serial production in 12 to 18 months and consequently it is very important to accurately understand possible problems during initial testing. If we make wrong conclusions it will delay assigned development time and possibly come in position that development went to wrong direction. Technical papers usually describe achieved results but without complete picture of problem which they have to overcome in order to achieve development goals. With such motivation the material discussed at this paper describes what had to done to make prototype engine to run correctly and refers to the turbojet engine TJE-200 at the EDePro company.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 19-22
EXPERIMENTAL ANALYSIS OF HIGH-SPEED GEARBOXES
With the rise of rotation speed of the gears in the gearboxes several phenomena that can significantly affect the gearbox energy efficiency and reliability occur. A lot of experimental data is available in literature for peripheral speeds below 40-60 m/s. But above this value some load parameters are changing their trends so this value can be classified as a limit between low and high-speed application. The main causes of power loss in gearboxes are tooth mesh losses, bearing losses, churning, windage, oil pocketing and gear drag. Some literature shows that windage losses which occur due to sliding friction of the high-speed gears in the oil-mist environment in the gearbox housing can be up to 30% or even more of the entire gear drive meshing losses. The phenomena of squeezing out the oil from the gear meshing area can also add more power losses in the system. In the worst case when the backlash is very small, these phenomena can even create oil blockage. Some problems with hydrodynamic losses due oil retaining in some housing pockets can also lead to lower energy efficiency. All of the mentioned hydrodynamic losses are negligible in the low-speed gearboxes, but in high-speed gearboxes they can exceed basic gear teeth meshing losses and even become larger.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 19-22
EXPERIMENTAL ANALYSIS OF HIGH-SPEED GEARBOXES
With the rise of rotation speed of the gears in the gearboxes several phenomena that can significantly affect the gearbox energy efficiency and reliability occur. A lot of experimental data is available in literature for peripheral speeds below 40-60 m/s. But above this value some load parameters are changing their trends so this value can be classified as a limit between low and high-speed application. The main causes of power loss in gearboxes are tooth mesh losses, bearing losses, churning, windage, oil pocketing and gear drag. Some literature shows that windage losses which occur due to sliding friction of the high-speed gears in the oil-mist environment in the gearbox housing can be up to 30% or even more of the entire gear drive meshing losses. The phenomena of squeezing out the oil from the gear meshing area can also add more power losses in the system. In the worst case when the backlash is very small, these phenomena can even create oil blockage. Some problems with hydrodynamic losses due oil retaining in some housing pockets can also lead to lower energy efficiency. All of the mentioned hydrodynamic losses are negligible in the low-speed gearboxes, but in high-speed gearboxes they can exceed basic gear teeth meshing losses and even become larger.
- Open Access
- 4 August 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (8)
Analysis and design of the gas generator multifunctional bulkhead considering the thermal and structural loads
The operation of gas generators brings relatively high thermo-mechanical loads on the gas generator structure. The objective of this article is to determine the operating conditions, in terms of mechanical loads at extremely high temperatures in very limited and narrow space, of a multifunctional bulkhead for application on specific kinds of gas generators with back-to-back rotor concept. The paper contains numerical analysis and experimental investigation for determining the loads and behavior of the structure. Numerical analysis indicates that there is significant influence of the Tesla turbine effect on flow parameters. Also, uneven pressure distribution and significant thermal loads are identified. With experimental investigation and subsequent exploitation tests, it was concluded that the presented methodology identifies the operating conditions, truthfully simulates the bulkhead stress state and deformations and that the presented design solution satisfied all demands. Regarding results obtained by these numerical simulations, the innovative design solution for the multifunctional bulkhead was proposed.
- 4 August 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (8)
Open AccessAnalysis and design of the gas generator multifunctional bulkhead considering the thermal and structural loads
The operation of gas generators brings relatively high thermo-mechanical loads on the gas generator structure. The objective of this article is to determine the operating conditions, in terms of mechanical loads at extremely high temperatures in very limited and narrow space, of a multifunctional bulkhead for application on specific kinds of gas generators with back-to-back rotor concept. The paper contains numerical analysis and experimental investigation for determining the loads and behavior of the structure. Numerical analysis indicates that there is significant influence of the Tesla turbine effect on flow parameters. Also, uneven pressure distribution and significant thermal loads are identified. With experimental investigation and subsequent exploitation tests, it was concluded that the presented methodology identifies the operating conditions, truthfully simulates the bulkhead stress state and deformations and that the presented design solution satisfied all demands. Regarding results obtained by these numerical simulations, the innovative design solution for the multifunctional bulkhead was proposed.
- Open Access
- 7 May 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (5)
Research of expendable turbojet tubular combustion chamber
This paper presents research related to the tubular combustion chamber of an expendable turbojet. Although annular combustors are dominant at present, tubular combustors are still attractive because they are simpler to produce and require lower amounts of air flow for testing. The objective of this research was to assess the combustor’s primary zone configuration, and four configurations were tested to obtain experimental answers for use in future work. The configuration of the combustion chamber is a simple and classic design in line with its expendable purpose. The test methodology was to perform initial testing of the primary and secondary zones under atmospheric conditions using the four configurations, and then to subsequently complete the combustor using the best configuration. The complete combustor was then tested under both atmospheric conditions and working conditions. The results showed that the stability margin was wide enough to cover the combustor’s entire working area. The measured efficiency and pressure drop were in very good agreement with the corresponding designed values. The design and testing methodology proposed here could be used for similar scientific and engineering research applications.
- 7 May 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (5)
Open AccessResearch of expendable turbojet tubular combustion chamber
This paper presents research related to the tubular combustion chamber of an expendable turbojet. Although annular combustors are dominant at present, tubular combustors are still attractive because they are simpler to produce and require lower amounts of air flow for testing. The objective of this research was to assess the combustor’s primary zone configuration, and four configurations were tested to obtain experimental answers for use in future work. The configuration of the combustion chamber is a simple and classic design in line with its expendable purpose. The test methodology was to perform initial testing of the primary and secondary zones under atmospheric conditions using the four configurations, and then to subsequently complete the combustor using the best configuration. The complete combustor was then tested under both atmospheric conditions and working conditions. The results showed that the stability margin was wide enough to cover the combustor’s entire working area. The measured efficiency and pressure drop were in very good agreement with the corresponding designed values. The design and testing methodology proposed here could be used for similar scientific and engineering research applications.
- Open Access
- 1 January 2022
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Industrija
- Vol. 50 (1) , 21-30
Indoor air quality in elderly homes in Serbia: Evidence-based design methodology
This study represents the first phase of research into the relationship between indoor air quality and the architectural and thermotechnical characteristics of buildings. The focus is on specific categories of users such as the elderly. The research methodology based on the scientific method is presented, which examines the condition of real objects on the territory of the Republic of Serbia. The aim is to provide a structured methodology for establishing the link between architecture, mechanical systems and indoor air quality, on evidence-based design principles, in order to propose guidelines for future interventions in the construction or adaptation of facilities for the elderly. Second objective of the study is to point to the relevance of contextualized interventions according to the target user groups and reinforce application of scientific evidence in contemporary building design. Namely, tailor-made solutions would be necessary in the future, and consideration towards different user needs should be framed and structured to meaningfully operationalize the design.
- 1 January 2022
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Industrija
- Vol. 50 (1) , 21-30
Open AccessIndoor air quality in elderly homes in Serbia: Evidence-based design methodology
This study represents the first phase of research into the relationship between indoor air quality and the architectural and thermotechnical characteristics of buildings. The focus is on specific categories of users such as the elderly. The research methodology based on the scientific method is presented, which examines the condition of real objects on the territory of the Republic of Serbia. The aim is to provide a structured methodology for establishing the link between architecture, mechanical systems and indoor air quality, on evidence-based design principles, in order to propose guidelines for future interventions in the construction or adaptation of facilities for the elderly. Second objective of the study is to point to the relevance of contextualized interventions according to the target user groups and reinforce application of scientific evidence in contemporary building design. Namely, tailor-made solutions would be necessary in the future, and consideration towards different user needs should be framed and structured to meaningfully operationalize the design.
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 32, 112-117
Experimental verification of performance of tip-jet helicopter propulsion system
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 32, 112-117
Experimental verification of performance of tip-jet helicopter propulsion system