MSMiloš Stanković

Miloš Stanković

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Miloš Stanković has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Windage losses of the high-speed cylindrical gear drives

    by Aleksandar Dimić, Nenad Kolarević, Miloš Stanković, Dimitrije Mihajlović

    High-speed gears with a pitch line velocity exceeding 60 m/s are vital components in the transmission of power and motion in aircraft gearboxes. High demands are placed on them in terms of reliability and energy efficiency. At the same time, their operating conditions (load, speed, temperature) are very unfavourable. One of the main causes of power losses in such gears are windage losses. In this paper, an analysis of windage losses is carried out for a gearbox configuration applied in the aviation industry. Current analytical models are applied to calculate the windage losses. It has been shown that windage losses can be as much as 34 % of gear drive meshing losses and must be studied as such in detail in the design phase of high-speed gear drives.

  • INITIAL EXPENDABLE TURBOJET PROTOTYPE TESTING EXPIRIENCES

    by Nikola Davidović, Nenad Kolarević, Milos Stanković, Marko Miloš

    Expendable turbojets, typically in thrust range from 40 to 400 daN, are used in target drones and missiles. Because of their usage they are designed to be simple and cheap rather to have some challenged performances according to [1],[2] and [3]. Also, because of their applications they are not requiring rigorous certifications as turbojets for man applications. Usually they are certificated together with the system in which they are installed. This paper is presenting experiences with initial prototype testing. At the moment when designed engine is produced and when some of component or subsystem testing are finished, we have to start with the very first tests. The point is that we will have to check performance of the engine which has to be running for the first time. If everything is fine during the first test and the results are very similar to expecting values it will be perfect. But usually in the engineering world it will not be the case. More than this we have to solve many small issues until we can run the prototype engine with confidence. On the other hand these days time for development is very limited, it is expected that such engine is ready for serial production in 12 to 18 months and consequently it is very important to accurately understand possible problems during initial testing. If we make wrong conclusions it will delay assigned development time and possibly come in position that development went to wrong direction. Technical papers usually describe achieved results but without complete picture of problem which they have to overcome in order to achieve development goals. With such motivation the material discussed at this paper describes what had to done to make prototype engine to run correctly and refers to the turbojet engine TJE-200 at the EDePro company.

  • EXPERIMENTAL ANALYSIS OF HIGH-SPEED GEARBOXES

    by Nenad Kolarević, Milosav Ognjanović, Miloš Stanković, Aleksandar Dimić, Nikola Davidović, Marko Miloš

    With the rise of rotation speed of the gears in the gearboxes several phenomena that can significantly affect the gearbox energy efficiency and reliability occur. A lot of experimental data is available in literature for peripheral speeds below 40-60 m/s. But above this value some load parameters are changing their trends so this value can be classified as a limit between low and high-speed application. The main causes of power loss in gearboxes are tooth mesh losses, bearing losses, churning, windage, oil pocketing and gear drag. Some literature shows that windage losses which occur due to sliding friction of the high-speed gears in the oil-mist environment in the gearbox housing can be up to 30% or even more of the entire gear drive meshing losses. The phenomena of squeezing out the oil from the gear meshing area can also add more power losses in the system. In the worst case when the backlash is very small, these phenomena can even create oil blockage. Some problems with hydrodynamic losses due oil retaining in some housing pockets can also lead to lower energy efficiency. All of the mentioned hydrodynamic losses are negligible in the low-speed gearboxes, but in high-speed gearboxes they can exceed basic gear teeth meshing losses and even become larger.

  • Open Access

    Optimization of the lubrication conditions for minimization of the operating temperature of the high-speed ball bearings

    by Nenad M. Kolarević, Miloš B. Stanković, Aleksandar R. Dimić, Dimitrije M. Mihajlović, Dragan B. Nauparac

    Bearing lubrication for high speed application (above 20000 rpm) has significant influence on the bearing heat generation and consenquently bearing operating temperature. For application in aerospace industry the selection of lubricant type, its amount and lubrication method should be carefuly conducted in order to achieve desired life and minimal weight. In this paper, experimental research was carried out in order to check whether and to what extent an open loop system can achieve similar bearing thermal behaviour as in a closed loop system. Tests were conducted on high-speed bearings of a turbo shaft engine. The experimental results showed that the open loop system, with oil mist lubrication, can achieve similar bearing operating temperature as the closed loop system, which operates with oil circulation, with the advantage of having a significantly lower mass. Also, a variation of lubrication conditions for open loop method, air pressure and oil amount, was carried out in order to minimize the operating temperature of high speed angular ball bearings. It has been shown that there is a combination of these two parameters that gives the least heating of high-speed bearings.


  • Open Access

    Levels of antioxidant enzyme activities in cultured rainbow trout (Oncorhynchus mykiss) fed with different diet compositions

    by J. S. Vranković, M. B. Stanković, Z. Z. Marković

    The recent trend for rainbow trout diets to be higher in lipid content may increase the lipid concentration in fish and lipid peroxidation, which could lead to oxidative stress and affect fish health. In the present work, an evaluation of the possible effects of different fish diets on antioxidant enzyme levels was carried out on two aquaculture groups of rainbow trout (Oncorhynchus mykiss). The fish from one group were fed a diet containing 5% more crude lipids, than the diet used for the other group. The objective was to determine the effects of different concentrations of dietary lipid on the antioxidant defense enzymes superoxide dismutase (SOD), catalase (CAT), glutathione peroxidase (GPx), glutathione reductase (GR), and glutathione-S-transferase (GST) in the liver and muscle of rainbow trout. All enzymes showed an increasing trend in fish fed with a diet containing more lipids. GST was observed to be the most sensitive antioxidant enzyme, followed by SOD and GPx, and finally by CAT and GR. These results provided data indicating the prooxidative effects of higher dietary lipid levels and suggested that dietary lipid plays an important role in determining fish susceptibility to oxidative stress.


  • Experimental verification of performance of tip-jet helicopter propulsion system

    by Nenad Kolarević, Stevan Crnojević, Miloš Stanković, Nenad Latković, Marko Miloš


  • Perlite as a potential support for nickel catalyst in the process of sunflower oil hydrogenation

    by V. Radonjić, J. Krstić, D. Lončarević, D. Jovanović, N. Vukelić, M. Stanković, D. Nikolova, M. Gabrovska


  • The state of nickel in the silver modified NiMg/SiO2 vegetable oil hydrogenation catalysts

    by M. Gabrovska, D. Nikolova, J. Krstić, M. Stanković, P. Stefanov, R. Edreva-Kardjieva, D. Jovanović

    Two series of silver modified Ni-Mg materials were synthesized by precipitation-deposition on SiO2 support derived from two silica sources: diatomite activated at 800°C (Series a; Mg/Ni = 0.1 and SiO2/Ni = 1.07) and synthetic water glass (Series b; Mg/Ni = 0.1 and SiO2/Ni = 1.15). The modification with silver was made at three molar Ag/Ni ratios, namely 0.0025, 0.025, and 0.1. The effects of the source of the silica support and the silver presence and content on the nickel state in the silver modified reduced-passivated NiMg/SiO2 precursors of the vegetable oil hydrogenation catalyst were established by X-ray diffraction and X-ray photoelectron spectroscopy techniques. The passivation procedure was applied in order to protect the metallic nickel particles from further oxidation. The crystallization of the formed nickel hydrosilicate phases depends on the source of the silica support, more expressed in the diatomite supported samples. It was shown that the silver modification of the NiMg/SiO2 precursors enhances the reduction of the nickel hydrosilicates accompanied by formation of relatively smaller metallic nickel particles, more pronounced in the water glass supported precursors. The increase of the silver content in the water glass deposited samples is responsible for the metallic nickel dispersion increase. The higher content of the Ni0 particles on the surface of the diatomite deposited samples is in accordance with the higher stability of the larger metallic nickel crystallites to oxidation during the passivation step. On contrary, higher dispersed Ni0 particles on the surface of the water glass supported samples are more susceptible to the oxida