Mykola Komar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mykola Komar has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Denys Mykhailovskyi
Kyiv National University of Construction and Architecture
7 shared publications Денис Михайловський
Київський національний університет будівництва і архітектури
4 shared publications- Denis Mykhaylovskyi
Kyiv National University of Construction and Architecture
2 shared publications - Bogdan Bondarchuk
Київський національний університет будівництва і архітектури
1 shared publication Kyiv National University of Construction and Architecture
1 shared publicationOleh Komar
Kyiv National University of Construction and Architecture
1 shared publication
Latest Publications
- Open Access
- 30 October 2025
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 115
Glued laminated timber beam reinforced with composite strips
Modern trends in the development of the construction industry demand increased attention to environmental aspects. This leads to the growing popularity of materials that are environmentally friendly and have minimal negative impact on the environment. At the same time, such materials must possess high strength and resistance to external influences and loads. In this context, timber structures are gaining widespread use. They are made from renewable natural resources and are characterized by relatively high strength and low weight, which qualifies them as sustainable building materials. Despite certain disadvantages of wood, such as shrinkage, decay, and anisotropic physical and mechanical properties, these drawbacks can be almost completely eliminated in glued laminated timber structures. In particular, glued laminated timber beams are key elements in many structures and are widely used in construction. Therefore, the issue of increasing their stiffness and strength through reinforcement with composite materials is especially relevant. This paper proposes a reinforcement technology, a methodology for determining the stress–strain state, and a calculation method for glued laminated timber beams reinforced with composite strips. The results of deformation parameters of the experimental model are presented, including actual flexural modules of elasticity, maximum longitudinal stresses at mid-span, at the load application axis, and at the support axis. The actual maximum load-bearing capacity of the experimental model reinforced with composite strips is determined and compared with numerical studies conducted in a modern software package.
- 30 October 2025
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 115
Open AccessGlued laminated timber beam reinforced with composite strips
Modern trends in the development of the construction industry demand increased attention to environmental aspects. This leads to the growing popularity of materials that are environmentally friendly and have minimal negative impact on the environment. At the same time, such materials must possess high strength and resistance to external influences and loads. In this context, timber structures are gaining widespread use. They are made from renewable natural resources and are characterized by relatively high strength and low weight, which qualifies them as sustainable building materials. Despite certain disadvantages of wood, such as shrinkage, decay, and anisotropic physical and mechanical properties, these drawbacks can be almost completely eliminated in glued laminated timber structures. In particular, glued laminated timber beams are key elements in many structures and are widely used in construction. Therefore, the issue of increasing their stiffness and strength through reinforcement with composite materials is especially relevant. This paper proposes a reinforcement technology, a methodology for determining the stress–strain state, and a calculation method for glued laminated timber beams reinforced with composite strips. The results of deformation parameters of the experimental model are presented, including actual flexural modules of elasticity, maximum longitudinal stresses at mid-span, at the load application axis, and at the support axis. The actual maximum load-bearing capacity of the experimental model reinforced with composite strips is determined and compared with numerical studies conducted in a modern software package.
- 1 August 2025
- Published by Odessa State Academy of Civil Engineering and Architecture in Modern structures of metal and wood
- No. 29
NUMERICAL MODELING OF THE BEHAVIOR OF A HYBRID-REINFORCED TIMBER BEAM USING PLANE FINITE ELEMENTS
The study is devoted to the numerical modeling of reinforced wooden beams using the LIRA-SAPR software package. One of the main disadvantages of wooden beams is their excessive flexibility, which leads to large deflections and displacements. Reinforcing wooden beams with stiffening elements is an effective method for increasing their rigidity and reducing internal stresses. However, in current engineering practice, there is a lack of design guidelines and examples for modeling such reinforced wooden structures using modern software tools. Therefore, the aim of this work is to investigate different methods for modeling reinforcement in wooden beams using finite element analysis. The paper presents an analysis of recent publications where different reinforcement types—such as basalt, carbon, and glass fiber—were used in wooden structures. Special attention is given to the challenge of numerically modeling such reinforcements, particularly when using planar finite elements instead of volumetric ones, as this approach significantly reduces computational complexity. Three reinforcement modeling methods are proposed and tested: 1) placing reinforcing bars between planar finite element nodes; 2) adjusting the modulus of elasticity of the elements to reflect the combined stiffness of wood and reinforcement; 3) modeling reinforcement as a separate layer with equivalent cross-sectional area. Each method was implemented and analyzed for accuracy and practicality. Experimental data from full-scale beam tests were used for comparison. Results indicate that all three methods provide acceptable accuracy, with deviations from experimental deflection values averaging around 11%, which is considered satisfactory for wood materials. Stress distributions obtained through numerical analysis showed good agreement across methods, though each has specific advantages. For instance, modeling reinforcement as individual bars allows precise evaluation of stresses in wood, whereas layer-based modeling offers direct assessment of stresses in reinforcement elements. The study demonstrates that numerical modeling of reinforced wooden beams using planar finite elements in LIRA-SAPR is a reliable and efficient alternative to volumetric modeling. Each proposed method can be effectively applied depending on the design goal, offering engineers flexibility in structural analysis and optimization.
- 1 August 2025
- Published by Odessa State Academy of Civil Engineering and Architecture in Modern structures of metal and wood
- No. 29
NUMERICAL MODELING OF THE BEHAVIOR OF A HYBRID-REINFORCED TIMBER BEAM USING PLANE FINITE ELEMENTS
The study is devoted to the numerical modeling of reinforced wooden beams using the LIRA-SAPR software package. One of the main disadvantages of wooden beams is their excessive flexibility, which leads to large deflections and displacements. Reinforcing wooden beams with stiffening elements is an effective method for increasing their rigidity and reducing internal stresses. However, in current engineering practice, there is a lack of design guidelines and examples for modeling such reinforced wooden structures using modern software tools. Therefore, the aim of this work is to investigate different methods for modeling reinforcement in wooden beams using finite element analysis. The paper presents an analysis of recent publications where different reinforcement types—such as basalt, carbon, and glass fiber—were used in wooden structures. Special attention is given to the challenge of numerically modeling such reinforcements, particularly when using planar finite elements instead of volumetric ones, as this approach significantly reduces computational complexity. Three reinforcement modeling methods are proposed and tested: 1) placing reinforcing bars between planar finite element nodes; 2) adjusting the modulus of elasticity of the elements to reflect the combined stiffness of wood and reinforcement; 3) modeling reinforcement as a separate layer with equivalent cross-sectional area. Each method was implemented and analyzed for accuracy and practicality. Experimental data from full-scale beam tests were used for comparison. Results indicate that all three methods provide acceptable accuracy, with deviations from experimental deflection values averaging around 11%, which is considered satisfactory for wood materials. Stress distributions obtained through numerical analysis showed good agreement across methods, though each has specific advantages. For instance, modeling reinforcement as individual bars allows precise evaluation of stresses in wood, whereas layer-based modeling offers direct assessment of stresses in reinforcement elements. The study demonstrates that numerical modeling of reinforced wooden beams using planar finite elements in LIRA-SAPR is a reliable and efficient alternative to volumetric modeling. Each proposed method can be effectively applied depending on the design goal, offering engineers flexibility in structural analysis and optimization.
- Open Access
- 30 June 2025
- Published by Lutsk National Technical University in Сучасні технології та методи розрахунків у будівництві
- No. 23,p. 155-170
Чисельне моделювання деформування армованих дерев’яних балок з цільної та клеєної деревини
У статті розглядаються результати чисельного моделювання деформування дерев’яних балок з клеєної та цільної деревини, виконаного за допомогою програмного комплексу ЛІРА-САПР 2024 R2.3, що використовує метод скінчених елементів (МСЕ). Визначено можливість застосування цього програмного комплексу для проектування армованих конструкцій з деревини, що є актуальним питанням для реконструкції та підсилення будівельних елементів. Моделювання дозволяє детально аналізувати напружено-деформований стан конструкцій, прогнозувати їх поведінку під навантаженням, а також порівнювати результати з експериментальними дослідженнями та традиційними деформаційними методиками. Процес моделювання був здійснений з урахуванням ортотропії деревини, для чого використовувалися об'ємні скінчені елементи, що описують механічні характеристики матеріалу. Зокрема, для деревини були враховані модулі пружності вздовж та впоперек волокон, а також коефіцієнти Пуассона, визначені експериментальними шляхами. Для армованих елементів використовувалися аналогічні елементи, що моделюють вуглецеву стрічку та сталеву арматуру. Отримані результати чисельного моделювання були порівняні з даними експериментальних досліджень та результатами, отриманими за допомогою деформаційної методики. Статистичний аналіз показав, що чисельне моделювання в ПК ЛІРА-САПР має середнє відхилення від експериментальних даних на рівні 21% для балок з клеєної деревини та 6,5% для деформаційної методики. Для армованих балок відхилення становить 29% для МСЕ і 7,3% для деформаційної методики. Результати чисельного моделювання показали, що програмний комплекс ЛІРА-САПР дозволяє точно визначати напруження та деформації дерев’яних конструкцій, однак деформаційна методика продемонструвала кращу точність для армованих елементів. Статистичний аналіз підтвердив, що обидва підходи є ефективними для проектування, зокрема для армованих конструкцій з деревини, при цьому деформаційна методика є більш точною в умовах підвищеного навантаження. Визначено, що для проектування армованих дерев’яних конструкцій обидва підходи можуть бути використані в залежності від вимог до точності та швидкості моделювання
- 30 June 2025
- Published by Lutsk National Technical University in Сучасні технології та методи розрахунків у будівництві
- No. 23,p. 155-170
Open AccessЧисельне моделювання деформування армованих дерев’яних балок з цільної та клеєної деревини
У статті розглядаються результати чисельного моделювання деформування дерев’яних балок з клеєної та цільної деревини, виконаного за допомогою програмного комплексу ЛІРА-САПР 2024 R2.3, що використовує метод скінчених елементів (МСЕ). Визначено можливість застосування цього програмного комплексу для проектування армованих конструкцій з деревини, що є актуальним питанням для реконструкції та підсилення будівельних елементів. Моделювання дозволяє детально аналізувати напружено-деформований стан конструкцій, прогнозувати їх поведінку під навантаженням, а також порівнювати результати з експериментальними дослідженнями та традиційними деформаційними методиками. Процес моделювання був здійснений з урахуванням ортотропії деревини, для чого використовувалися об'ємні скінчені елементи, що описують механічні характеристики матеріалу. Зокрема, для деревини були враховані модулі пружності вздовж та впоперек волокон, а також коефіцієнти Пуассона, визначені експериментальними шляхами. Для армованих елементів використовувалися аналогічні елементи, що моделюють вуглецеву стрічку та сталеву арматуру. Отримані результати чисельного моделювання були порівняні з даними експериментальних досліджень та результатами, отриманими за допомогою деформаційної методики. Статистичний аналіз показав, що чисельне моделювання в ПК ЛІРА-САПР має середнє відхилення від експериментальних даних на рівні 21% для балок з клеєної деревини та 6,5% для деформаційної методики. Для армованих балок відхилення становить 29% для МСЕ і 7,3% для деформаційної методики. Результати чисельного моделювання показали, що програмний комплекс ЛІРА-САПР дозволяє точно визначати напруження та деформації дерев’яних конструкцій, однак деформаційна методика продемонструвала кращу точність для армованих елементів. Статистичний аналіз підтвердив, що обидва підходи є ефективними для проектування, зокрема для армованих конструкцій з деревини, при цьому деформаційна методика є більш точною в умовах підвищеного навантаження. Визначено, що для проектування армованих дерев’яних конструкцій обидва підходи можуть бути використані в залежності від вимог до точності та швидкості моделювання
- Open Access
- 23 December 2024
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 15,p. 54-65
Application of laminated and cross-laminated timber in reconstruction and new construction
The article is devoted to the actual problem of restoration of construction objects of Ukraine destroyed as a result of military actions. The issue of manufacturing and effective application of cross-laminated timber panels and other products made of laminated timber for use in recon-struction, restoration of damaged construction objects and new construction is considered. Why can the availability of the raw material base, its renewability and ease of extraction and processing contribute. Cross-laminated timber is a relatively new building material based on timber, which is an array of boards laminated in layers in a mutually perpendicular direction. The layers of lumber are laminated together under pressure, forming a virtually monolithic slab. The production of cross-laminated timber solves one of the important problems, namely the use of small and medium-sized cross-sections of boards to create large arrays, which allows you to signifi-cantly save commercial timber. The main advantages of laminated and cross-laminated timber as building materials are given and the feasibility of their application for buildings and structures of various functional purposes is proven. Examples of modern high-rise buildings con-structed using cross-laminated timber panels around the world are presented. Due to the elimination of some of the defects of whole timber and the preservation of one of the main advantages, namely, low weight with relatively high strength values, laminated and cross-laminated timber can become one of the main materials for the development of new areas and the restoration or reconstruction of damaged ones as a re-sult of military actions, buildings and structures of various purposes. The low weight of structures made of laminated and cross-laminated timber will reduce the cost of strengthening existing structures and the cost of ma-terials for new foundations in the case of new con-struction by at least 30% in comparison with houses erected using more traditional methods - these materials.
- 23 December 2024
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 15,p. 54-65
Open AccessApplication of laminated and cross-laminated timber in reconstruction and new construction
The article is devoted to the actual problem of restoration of construction objects of Ukraine destroyed as a result of military actions. The issue of manufacturing and effective application of cross-laminated timber panels and other products made of laminated timber for use in recon-struction, restoration of damaged construction objects and new construction is considered. Why can the availability of the raw material base, its renewability and ease of extraction and processing contribute. Cross-laminated timber is a relatively new building material based on timber, which is an array of boards laminated in layers in a mutually perpendicular direction. The layers of lumber are laminated together under pressure, forming a virtually monolithic slab. The production of cross-laminated timber solves one of the important problems, namely the use of small and medium-sized cross-sections of boards to create large arrays, which allows you to signifi-cantly save commercial timber. The main advantages of laminated and cross-laminated timber as building materials are given and the feasibility of their application for buildings and structures of various functional purposes is proven. Examples of modern high-rise buildings con-structed using cross-laminated timber panels around the world are presented. Due to the elimination of some of the defects of whole timber and the preservation of one of the main advantages, namely, low weight with relatively high strength values, laminated and cross-laminated timber can become one of the main materials for the development of new areas and the restoration or reconstruction of damaged ones as a re-sult of military actions, buildings and structures of various purposes. The low weight of structures made of laminated and cross-laminated timber will reduce the cost of strengthening existing structures and the cost of ma-terials for new foundations in the case of new con-struction by at least 30% in comparison with houses erected using more traditional methods - these materials.
- 28 June 2024
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 14
Analysis of stress-strain state of plates made of crosslaminated timber reinforced with composite tapes
In our time, the construction industry is actively developing in various directions. Constructions with large cross-sections are being replaced by counterparts with reduced cross-sectionsusing various types of reinforcement.Cross-laminated timber (CLT) panels are a massive, multi-layered glued timber construction material. For high-rise building structures and wooden buildings, the use of CLT panels is the primary method for arranging floors and roofs. Layers oftimber are glued together under pressure, forming a virtually ready-made panel. The layers of timber lamellas are laid perpendicular to each other, transversely. The outer layers usually have the same orientation, while the internal layers, perpendicular to the outer ones, may consist of cheaper wood to savecosts. Most often, softwood is used for the production of such panels as the most affordable.However, the production of such panels requires significant material costs. Therefore, research in the field of reinforcement of CLT panels to reduce their cross-section is relevant.Composite materials are leading in structural reinforcement now, as most of them have high resistance to various chemical influences, such as alkalis, acids, chlorides, sulfates, nitrates, and others.This allows them to be used both in industrial and agricultural construction, where there is a significant impact of the external environment on structures reinforced with composite materials, and in residential buildings, without harm to residents.After analyzing the stress-strain state through modeling in the LIRA CAD software package of CLT panels reinforced with composite strips and comparing them with similar panels without reinforcement, we can conclude that such materials canbe excellently combined with cross-laminated timber structures, allowing to increase the load-bearing capacity while reducing their cross-section.
- 28 June 2024
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 14
Analysis of stress-strain state of plates made of crosslaminated timber reinforced with composite tapes
In our time, the construction industry is actively developing in various directions. Constructions with large cross-sections are being replaced by counterparts with reduced cross-sectionsusing various types of reinforcement.Cross-laminated timber (CLT) panels are a massive, multi-layered glued timber construction material. For high-rise building structures and wooden buildings, the use of CLT panels is the primary method for arranging floors and roofs. Layers oftimber are glued together under pressure, forming a virtually ready-made panel. The layers of timber lamellas are laid perpendicular to each other, transversely. The outer layers usually have the same orientation, while the internal layers, perpendicular to the outer ones, may consist of cheaper wood to savecosts. Most often, softwood is used for the production of such panels as the most affordable.However, the production of such panels requires significant material costs. Therefore, research in the field of reinforcement of CLT panels to reduce their cross-section is relevant.Composite materials are leading in structural reinforcement now, as most of them have high resistance to various chemical influences, such as alkalis, acids, chlorides, sulfates, nitrates, and others.This allows them to be used both in industrial and agricultural construction, where there is a significant impact of the external environment on structures reinforced with composite materials, and in residential buildings, without harm to residents.After analyzing the stress-strain state through modeling in the LIRA CAD software package of CLT panels reinforced with composite strips and comparing them with similar panels without reinforcement, we can conclude that such materials canbe excellently combined with cross-laminated timber structures, allowing to increase the load-bearing capacity while reducing their cross-section.
- Open Access
- 17 April 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 112,p. 43-51
Definition of the stress-strain state of a glued laminated timber beam reinforced with composite strips using experimental method
The trend in the development of the construction industry worldwide requires increasing attention to ecological aspects, which means that materials with minimal negative impact on the environment are becoming increasingly popular. At the same time, these materials must possess high strength and durability against various external influences and loads. From this perspective, constructions made of wood and its derivatives are gaining the most popularity. Such constructions, made from renewable natural resources, exhibit relatively high strength at relatively low density, thus belonging to such materials. Although wood has its drawbacks, such as susceptibility to drying, rotting, and anisotropy of properties, these drawbacks can be completely mitigated in glued laminated timber structures. Glued laminated timber beams, which are the primary structural element of many buildings and structures, are the most widespread. Therefore, the issue of significantly increasing their rigidity and strength through reinforcement with composite materials is particularly relevant. This article proposes a methodology for determining the stress-strain state of a glued laminated timber beam reinforced with composite strips. The results include deformation parameters of the experimental model, actual elastic modules during bending, maximum longitudinal stresses at the center of the span, along the load application axis, and along the support axis. Additionally, maximum transverse and shear stresses along the load application axis and along the support axis are determined. The actual maximum load-bearing capacity of the experimental model reinforced with composite strips is established.
- 17 April 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 112,p. 43-51
Open AccessDefinition of the stress-strain state of a glued laminated timber beam reinforced with composite strips using experimental method
The trend in the development of the construction industry worldwide requires increasing attention to ecological aspects, which means that materials with minimal negative impact on the environment are becoming increasingly popular. At the same time, these materials must possess high strength and durability against various external influences and loads. From this perspective, constructions made of wood and its derivatives are gaining the most popularity. Such constructions, made from renewable natural resources, exhibit relatively high strength at relatively low density, thus belonging to such materials. Although wood has its drawbacks, such as susceptibility to drying, rotting, and anisotropy of properties, these drawbacks can be completely mitigated in glued laminated timber structures. Glued laminated timber beams, which are the primary structural element of many buildings and structures, are the most widespread. Therefore, the issue of significantly increasing their rigidity and strength through reinforcement with composite materials is particularly relevant. This article proposes a methodology for determining the stress-strain state of a glued laminated timber beam reinforced with composite strips. The results include deformation parameters of the experimental model, actual elastic modules during bending, maximum longitudinal stresses at the center of the span, along the load application axis, and along the support axis. Additionally, maximum transverse and shear stresses along the load application axis and along the support axis are determined. The actual maximum load-bearing capacity of the experimental model reinforced with composite strips is established.
- Open Access
- 26 December 2022
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 11,p. 53-60
ANALYSIS OF THE STATE OF STRESS AND DEFORMATION OF GLAMINATED WOOD FRAMES REINFORCED WITH COMPOSITE TAPES
In the modern world, the construction industry is successfully developing in various directions. Large-sized structures are replaced by analogues reduced in cross-section with the help of various types of reinforcement. Frames refer to flat spacer structures. Modern glued frames are often solid. Cross-section (lattice) structures of this class were used mainly from solid wood. Currently, they are practically not used due to the lack of their industrial production. Frame structures mainly consist of rectilinear elements and allow the presence of rigid (frame) nodes. Rigid nodes of three-hinged frames are usually called eaves, because they have to be constructed exactly under the eaves of the building. These units ensure joint operation of crossbars and racks, which reduces bending moments in the crossbar. In addition, it is easily proven that the maximum bending moment in the cornice nodes of the frames is less than the maximum moment in the beams with the same spans. Their ratio is equal to the ratio of the height of the frame strut to the arrow of the rise of the ridge joint relative to the support joints. Accordingly, unlike beams, frames can cover larger spans. However, it is the eaves units that have the largest cross-section in frames made of glued wood, which requires significant material consumption. Therefore, research in the field of strengthening such nodes to reduce their cross-section is relevant. Composite materials are currently one of the leaders in strengthening structures because most composite materials are well resistant to many chemical influences: alkalis, acids, chlorides, sulfates, nitrates, and others. This allows them to be used both in industrial and agricultural construction, where there is a direct impact of the external environment on the structure reinforced with composite materials, and in residential buildings without harm to residents. After analyzing the stress-strain state by modeling in the LIRA CAD software complex of broken-glued three-hinged frames made of glued wood with integrally glued eaves nodes with a crossbar connection with a rack through toothed spikes along the bisector of the corner reinforced with composite tapes and comparing with similar frames without reinforcement, we can to conclude that such materials can be perfectly combined with structures made of solid and glued wood, allowing to increase the load-bearing capacity while reducing their cross-section.
- 26 December 2022
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 11,p. 53-60
Open AccessANALYSIS OF THE STATE OF STRESS AND DEFORMATION OF GLAMINATED WOOD FRAMES REINFORCED WITH COMPOSITE TAPES
In the modern world, the construction industry is successfully developing in various directions. Large-sized structures are replaced by analogues reduced in cross-section with the help of various types of reinforcement. Frames refer to flat spacer structures. Modern glued frames are often solid. Cross-section (lattice) structures of this class were used mainly from solid wood. Currently, they are practically not used due to the lack of their industrial production. Frame structures mainly consist of rectilinear elements and allow the presence of rigid (frame) nodes. Rigid nodes of three-hinged frames are usually called eaves, because they have to be constructed exactly under the eaves of the building. These units ensure joint operation of crossbars and racks, which reduces bending moments in the crossbar. In addition, it is easily proven that the maximum bending moment in the cornice nodes of the frames is less than the maximum moment in the beams with the same spans. Their ratio is equal to the ratio of the height of the frame strut to the arrow of the rise of the ridge joint relative to the support joints. Accordingly, unlike beams, frames can cover larger spans. However, it is the eaves units that have the largest cross-section in frames made of glued wood, which requires significant material consumption. Therefore, research in the field of strengthening such nodes to reduce their cross-section is relevant. Composite materials are currently one of the leaders in strengthening structures because most composite materials are well resistant to many chemical influences: alkalis, acids, chlorides, sulfates, nitrates, and others. This allows them to be used both in industrial and agricultural construction, where there is a direct impact of the external environment on the structure reinforced with composite materials, and in residential buildings without harm to residents. After analyzing the stress-strain state by modeling in the LIRA CAD software complex of broken-glued three-hinged frames made of glued wood with integrally glued eaves nodes with a crossbar connection with a rack through toothed spikes along the bisector of the corner reinforced with composite tapes and comparing with similar frames without reinforcement, we can to conclude that such materials can be perfectly combined with structures made of solid and glued wood, allowing to increase the load-bearing capacity while reducing their cross-section.
- Open Access
- 11 November 2022
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 109,p. 239-262
Engineering method of calculating laminated timber elements reinforced with composite tapes
Annotation. In today's world, construction requires environmentally friendly materials that cause minimal damage to the environment. At the same time, they must have great strength and be resistant to various types of external influences. Timber structures, which are made of renewable natural materials and have a relatively high strength, can rightfully be considered as such material. Despite the fact that timber itself has certain negative properties, namely the tendency to shrink and swell, rot, anisotropy of properties, which requires special attention in construction, in laminated timber structures (LTS) these disadvantages are already more manageable. Beams are one of the main laminated timber structures. Laminated timber beams reinforcement allows to significantly increasing their stiffness and strength. The article proposes a methodology for calculating laminated timber elements of rectangular section reinforced with composite tapes. Refined formulas for determining the efficient geometric and mechanical characteristics are provided. The proposed method was compared with another analytical method of calculation and with the numerical method of modeling in the LIRA-CAD software complex using the finite element method. It was proved that this method of reinforcing laminated timber structures is promising and relevant.
- 11 November 2022
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 109,p. 239-262
Open AccessEngineering method of calculating laminated timber elements reinforced with composite tapes
Annotation. In today's world, construction requires environmentally friendly materials that cause minimal damage to the environment. At the same time, they must have great strength and be resistant to various types of external influences. Timber structures, which are made of renewable natural materials and have a relatively high strength, can rightfully be considered as such material. Despite the fact that timber itself has certain negative properties, namely the tendency to shrink and swell, rot, anisotropy of properties, which requires special attention in construction, in laminated timber structures (LTS) these disadvantages are already more manageable. Beams are one of the main laminated timber structures. Laminated timber beams reinforcement allows to significantly increasing their stiffness and strength. The article proposes a methodology for calculating laminated timber elements of rectangular section reinforced with composite tapes. Refined formulas for determining the efficient geometric and mechanical characteristics are provided. The proposed method was compared with another analytical method of calculation and with the numerical method of modeling in the LIRA-CAD software complex using the finite element method. It was proved that this method of reinforcing laminated timber structures is promising and relevant.
- Open Access
- 29 June 2022
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 10,p. 4-10
ANALYSIS OF RESEARCH APPLICATIONS OF COMPOSITE TAPE FOR REINFORCEMENT OF WOODEN STRUCTURES
In the XXI century, the construction industry is developing at a rapid pace. Competitors of the same material, but reduced in cross-section by strengthening them with composite materials, compete with large-sized structures. Composite materials are considered to have relatively new operational and physical-mechanical properties, which are created due to the joint work of two or more components that differ in structure, chemical composition, physical and mechanical characteristics. One of the first composite materials is considered to be reinforced concrete, which was widely used in the late XIX century. At the beginning of the XX century for the needs of shipbuilding, aviation, aerospace, etc., modern composite materials such as fiberglass, consisting of artificial continuous glass fibers and artificial polymer matrix invented by A.K. Burov and his colleagues in the 30s of last century [1]. During the Great Patriotic War, fiberglass plates were used instead of aluminum in aircraft construction. In the 1960s, carbon fiber was developed in the United Kingdom and boron in the United States, which gave impetus to the development of a new generation of composite materials with high modulus of elasticity and high strength, which significantly increased their scope. . It can be noted that most composite materials are well resistant to many chemical influences: alkalis, acids, chlorides, sulfates, nitrates and others. All of them are not dangerous to human health in normal operation with the use of personal protective equipment in the direct performance of reinforcement work. This allows them to be used both in industrial and agricultural construction where there is a direct impact of the external environment on the structure reinforced with composite materials, and in residential buildings without harm to residents. After analyzing the creation and use of composite materials to strengthen structures of different materials, as well as methods of their application and physical and mechanical properties, it is assumed that such materials can be perfectly combined with solid and glued wood structures, increasing load-bearing capacity while reducing their cross section.
- 29 June 2022
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 10,p. 4-10
Open AccessANALYSIS OF RESEARCH APPLICATIONS OF COMPOSITE TAPE FOR REINFORCEMENT OF WOODEN STRUCTURES
In the XXI century, the construction industry is developing at a rapid pace. Competitors of the same material, but reduced in cross-section by strengthening them with composite materials, compete with large-sized structures. Composite materials are considered to have relatively new operational and physical-mechanical properties, which are created due to the joint work of two or more components that differ in structure, chemical composition, physical and mechanical characteristics. One of the first composite materials is considered to be reinforced concrete, which was widely used in the late XIX century. At the beginning of the XX century for the needs of shipbuilding, aviation, aerospace, etc., modern composite materials such as fiberglass, consisting of artificial continuous glass fibers and artificial polymer matrix invented by A.K. Burov and his colleagues in the 30s of last century [1]. During the Great Patriotic War, fiberglass plates were used instead of aluminum in aircraft construction. In the 1960s, carbon fiber was developed in the United Kingdom and boron in the United States, which gave impetus to the development of a new generation of composite materials with high modulus of elasticity and high strength, which significantly increased their scope. . It can be noted that most composite materials are well resistant to many chemical influences: alkalis, acids, chlorides, sulfates, nitrates and others. All of them are not dangerous to human health in normal operation with the use of personal protective equipment in the direct performance of reinforcement work. This allows them to be used both in industrial and agricultural construction where there is a direct impact of the external environment on the structure reinforced with composite materials, and in residential buildings without harm to residents. After analyzing the creation and use of composite materials to strengthen structures of different materials, as well as methods of their application and physical and mechanical properties, it is assumed that such materials can be perfectly combined with solid and glued wood structures, increasing load-bearing capacity while reducing their cross section.
- Open Access
- 28 December 2021
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 9,p. 72-80
REINFORCEMENT OF COMPOSITE WOODEN STRUCTURES MATERIALS, CONDITION AND PROSPECTS
Today, there is a growing need in the construction industry for the introduction of ecological urban space and the use of materials from renewable natural resources, one of such building materials from ancient times was wood.Temples, castles, houses, bridges and other structures have been erected all over the world sinceancient times with the help of wooden structures.A large number of buildings and structures made of wood have been operating successfully for 300-400 years and are vivid examples of the durability of these structures. Nowadays, wooden construction is developing rapidly with the development of new technologies. After all, new woodworking technologies allow obtaining a spliced array ofwood, which solves many different issues of wood as a structural material. Recently, the constructionof glued timber (GT), which is often used to cover large spans (more than 100 m) and the constructionof cross-laminated timber (CLT) or CLT (cross laminated timber), which are often from an oddnumber of layers of boards with their mutually perpendicular arrangement in adjacent layers. Panels used in panel and panel-frame construction of buildings of various complexity of architectural form and number of storeys are made of CLT. Inworks [1-3] studies of efficiency and CLT and methods of their calculation are described in moredetail. However, some building requirements, such as the conditions for limiting the building height,when the use of relatively large cross-sections of plywood constructions, calculated in compliance with the requirements of the boundary conditions, is not possible. Therefore, the search and study of modified efficiencies, including reinforced ones, to increase the bearing capacity while reducing their cross section is becoming increasingly important.This publication is devoted to the review of the conducted researches reinforced and reinforcedwith composite materials of various efficiencies.
- 28 December 2021
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 9,p. 72-80
Open AccessREINFORCEMENT OF COMPOSITE WOODEN STRUCTURES MATERIALS, CONDITION AND PROSPECTS
Today, there is a growing need in the construction industry for the introduction of ecological urban space and the use of materials from renewable natural resources, one of such building materials from ancient times was wood.Temples, castles, houses, bridges and other structures have been erected all over the world sinceancient times with the help of wooden structures.A large number of buildings and structures made of wood have been operating successfully for 300-400 years and are vivid examples of the durability of these structures. Nowadays, wooden construction is developing rapidly with the development of new technologies. After all, new woodworking technologies allow obtaining a spliced array ofwood, which solves many different issues of wood as a structural material. Recently, the constructionof glued timber (GT), which is often used to cover large spans (more than 100 m) and the constructionof cross-laminated timber (CLT) or CLT (cross laminated timber), which are often from an oddnumber of layers of boards with their mutually perpendicular arrangement in adjacent layers. Panels used in panel and panel-frame construction of buildings of various complexity of architectural form and number of storeys are made of CLT. Inworks [1-3] studies of efficiency and CLT and methods of their calculation are described in moredetail. However, some building requirements, such as the conditions for limiting the building height,when the use of relatively large cross-sections of plywood constructions, calculated in compliance with the requirements of the boundary conditions, is not possible. Therefore, the search and study of modified efficiencies, including reinforced ones, to increase the bearing capacity while reducing their cross section is becoming increasingly important.This publication is devoted to the review of the conducted researches reinforced and reinforcedwith composite materials of various efficiencies.