Frederic Lazzarino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Frederic Lazzarino has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
Geert Vandenberghe
IMEC (Belgium)
3 shared publications- Danilo De Simone
IMEC, Leuven, Belgium
2 shared publications - Ming Mao
IMEC (Belgium)
2 shared publications - Vincent Truffert
STS/Advanced Patterning, Imec, Leuven, Belgium
2 shared publications Abhinav Pathak
IMEC (Belgium)
1 shared publication- Anabela Veloso
IMEC, Leuven, Belgium
1 shared publication
Latest Publications
- 25 May 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12056, 87-94
Middle-of-line plasma dry etch challenges for buried power rail integration
Buried power rail (BPR), a novel integration approach for further device scaling, brings in new patterning needs and requirements, the most importantly, the challenging middle-of-line (MOL) patterning process steps. In this paper, some of the critical plasma dry etch development processing results for the FinFET device flow with BPR integrated are presented. Mainly, the study was focused on plasma dry etch development of high aspect ratio Via contact to BPR metal (VBPR) and Trench contact etch (M0A) to the source/drain (S/D) device region. We demonstrate the short-free M0A (no attack on the neighboring gates) contact etch to the S/D, with the high etch selectivity values obtained in case of the dielectric SiO2 trench etch to the thin Si3N4 liner (deposited over epitaxial S/D), and subsequently the high selectivity values during SiN liner etch to the underlying S/D (SiN liner etch results in 0nm epitaxial film loss). Patterning of high aspect ratio (HAR) Via consisting of the multi-stack, SiO2/SiN/SiO2/SiN dielectric, landing on the bottom BPR metal was achieved, with the target critical dimension (CD) required to avoid shorting to the adjacent gates. Additionally, we report our learnings on how choice of buried power metal (W, Ru and Mo) impacts the etch requirements, i.e., the etch challenges associated by using Ru and Mo as a replacement for standardly used W metal.
- 25 May 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12056, 87-94
Middle-of-line plasma dry etch challenges for buried power rail integration
Buried power rail (BPR), a novel integration approach for further device scaling, brings in new patterning needs and requirements, the most importantly, the challenging middle-of-line (MOL) patterning process steps. In this paper, some of the critical plasma dry etch development processing results for the FinFET device flow with BPR integrated are presented. Mainly, the study was focused on plasma dry etch development of high aspect ratio Via contact to BPR metal (VBPR) and Trench contact etch (M0A) to the source/drain (S/D) device region. We demonstrate the short-free M0A (no attack on the neighboring gates) contact etch to the S/D, with the high etch selectivity values obtained in case of the dielectric SiO2 trench etch to the thin Si3N4 liner (deposited over epitaxial S/D), and subsequently the high selectivity values during SiN liner etch to the underlying S/D (SiN liner etch results in 0nm epitaxial film loss). Patterning of high aspect ratio (HAR) Via consisting of the multi-stack, SiO2/SiN/SiO2/SiN dielectric, landing on the bottom BPR metal was achieved, with the target critical dimension (CD) required to avoid shorting to the adjacent gates. Additionally, we report our learnings on how choice of buried power metal (W, Ru and Mo) impacts the etch requirements, i.e., the etch challenges associated by using Ru and Mo as a replacement for standardly used W metal.
- 1 May 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 40 (3) , 032803
Extreme contact shrink for back end of line connectivity
For the past 50 years, Moore’s law has been well followed by the semiconductor industry. The scaling of transistors and interconnects has been enabled not only by various technological advancements but also by novel patterning approaches. However, in order to keep up with Moore’s law, further shrinking at all levels of the integrated circuit is needed. Among them is the back end of line (BEOL), where increasingly smaller metal pitches require tight specifications for vias connecting metal lines. In this paper, BEOL via shrink options is investigated, targeting the bottom critical dimension (CD) 10.5 nm in order to land on metal pitch 21 nm lines below, while maintaining low defectivity, as well as low global and local CD uniformity (CDU and LCDU, respectively). Approaches to this shrink consist of modifications to the etch chemistry at different levels of the mask etch and liner-assisted shrink, either organic or inorganic. Numerical analysis of CD-scanning electron microscopy (CDSEM) images quantitatively shows the efficiency of different approaches via shrink, together with associated CDU, LCDU, and defectivity values. CDSEM results are supplemented by large-area voltage contrast defectivity and transmission electron microscopy data sets.
- 1 May 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 40 (3) , 032803
Extreme contact shrink for back end of line connectivity
For the past 50 years, Moore’s law has been well followed by the semiconductor industry. The scaling of transistors and interconnects has been enabled not only by various technological advancements but also by novel patterning approaches. However, in order to keep up with Moore’s law, further shrinking at all levels of the integrated circuit is needed. Among them is the back end of line (BEOL), where increasingly smaller metal pitches require tight specifications for vias connecting metal lines. In this paper, BEOL via shrink options is investigated, targeting the bottom critical dimension (CD) 10.5 nm in order to land on metal pitch 21 nm lines below, while maintaining low defectivity, as well as low global and local CD uniformity (CDU and LCDU, respectively). Approaches to this shrink consist of modifications to the etch chemistry at different levels of the mask etch and liner-assisted shrink, either organic or inorganic. Numerical analysis of CD-scanning electron microscopy (CDSEM) images quantitatively shows the efficiency of different approaches via shrink, together with associated CDU, LCDU, and defectivity values. CDSEM results are supplemented by large-area voltage contrast defectivity and transmission electron microscopy data sets.
- 26 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10957, 23
Impact of sequential infiltration synthesis (SIS) on roughness and stochastic nano-failures for EUVL patterning
Enhanced EUV lithography (EUVL) resist performance, combined with optimized post processing techniques, are vital to ensure continued scaling and meet the requirements for the industry N5 node and beyond. Sequential infiltration synthesis (SIS) is a post lithography technique that has the potential to significantly improve the EUVL patterning process for stochastic nano-failures and line roughness, both major topics in EUV lithography research. SIS is an ALD-like technique that infiltrates polymeric photoresists, forming a metal framework using the lithography pattern as a template. Hardening of the photoresist improves the pattern quality and gives more flexibility to subsequent pattern transfer steps. We have evaluated the performance of SIS for an EUV Chemically Amplified Resist (CAR) platform printing 32 nm pitch line/space patterns and ultimately structures that are representative of standard semiconductor manufacturing. A combined lithography-SIS-etch process and a standard lithography-etch process were optimized for an industry relevant stack with pattern transfer into a TiN layer. This allows for the first time a justified comparison between a EUVL-SIS and a standard EUVL patterning process, showing the benefits of SIS regarding roughness, exposure latitude and nano-failure mitigation. Power Spectral Density (PSD) analysis accurately demonstrates and explains the type of roughness improvement. Nano-failure analysis is done by measuring large areas at different exposure doses and shows the improvement of the nano-failure free window when applying a EUVL-SIS patterning process. We conclude by examining to which extent combining the best lithography process with an optimized SIS step will lead to a better roughness and nano-failure performance, essential to meeting industry requirements.
- 26 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10957, 23
Impact of sequential infiltration synthesis (SIS) on roughness and stochastic nano-failures for EUVL patterning
Enhanced EUV lithography (EUVL) resist performance, combined with optimized post processing techniques, are vital to ensure continued scaling and meet the requirements for the industry N5 node and beyond. Sequential infiltration synthesis (SIS) is a post lithography technique that has the potential to significantly improve the EUVL patterning process for stochastic nano-failures and line roughness, both major topics in EUV lithography research. SIS is an ALD-like technique that infiltrates polymeric photoresists, forming a metal framework using the lithography pattern as a template. Hardening of the photoresist improves the pattern quality and gives more flexibility to subsequent pattern transfer steps. We have evaluated the performance of SIS for an EUV Chemically Amplified Resist (CAR) platform printing 32 nm pitch line/space patterns and ultimately structures that are representative of standard semiconductor manufacturing. A combined lithography-SIS-etch process and a standard lithography-etch process were optimized for an industry relevant stack with pattern transfer into a TiN layer. This allows for the first time a justified comparison between a EUVL-SIS and a standard EUVL patterning process, showing the benefits of SIS regarding roughness, exposure latitude and nano-failure mitigation. Power Spectral Density (PSD) analysis accurately demonstrates and explains the type of roughness improvement. Nano-failure analysis is done by measuring large areas at different exposure doses and shows the improvement of the nano-failure free window when applying a EUVL-SIS patterning process. We conclude by examining to which extent combining the best lithography process with an optimized SIS step will lead to a better roughness and nano-failure performance, essential to meeting industry requirements.
- Open Access
- 1 January 2016
- Published by Technical Association of Photopolymers, Japan in Journal of Photopolymer Science and Technology
- Vol. 29 (3) , 501-507
Metal Containing Resist Readiness for HVM EUV Lithography
- 1 January 2016
- Published by Technical Association of Photopolymers, Japan in Journal of Photopolymer Science and Technology
- Vol. 29 (3) , 501-507
Open AccessMetal Containing Resist Readiness for HVM EUV Lithography
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 2380632X,p. 1-3
Integration of a k=2.3 spin-on polymer for the sub-28nm technology node using EUV lithography
In this work we integrate an advanced k=2.3 spin-on polymer at 40nm ½ pitch. K-value restoration techniques are investigated and complete k-value restoration is demonstrated using an in-situ HeH 2 plasma. An EUV compatible stack and a dielectric dual hard mask scheme is developed to pattern trenches with good uniformity and low litho-etch bias. The impact of scaling the dielectric spacing and of direct CMP on time dependent dielectric breakdown is also studied.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 2380632X,p. 1-3
Integration of a k=2.3 spin-on polymer for the sub-28nm technology node using EUV lithography
In this work we integrate an advanced k=2.3 spin-on polymer at 40nm ½ pitch. K-value restoration techniques are investigated and complete k-value restoration is demonstrated using an in-situ HeH 2 plasma. An EUV compatible stack and a dielectric dual hard mask scheme is developed to pattern trenches with good uniformity and low litho-etch bias. The impact of scaling the dielectric spacing and of direct CMP on time dependent dielectric breakdown is also studied.
- 11 March 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7640, 764011-764011-12
Printing the metal and contact layers for the 32- and 22-nm node: comparing positive and negative tone development process
A strong demand exists for techniques that can further extend the application of ArF immersion lithography. Besides techniques like litho-friendly design, dual exposure or patterning schemes, customized illumination modes, also alternative processing schemes are viable candidates to reach this goal. One of the most promising alternative process flows uses image reversal by means of a negative tone development (NTD) step with a FUJIFILM solvent-based developer. Traditionally, the printing of contacts and trenches is done by using a dark field mask in combination with positive tone resist and positive tone development. With NTD, the same features can be printed in positive resist using a light field mask, and consequently with a much better image contrast. In this paper, we present an overview of applications for the NTD technique, both for trench and contact patterning, comparing the NTD performance to that of the traditional positive tone development (PTD). This experimental work was performed on an ASML Twinscan XT:1900i scanner at 1.35 NA, and targets the contact/metal layers of the 32 & 22 nm node. For contact hole printing, we consider both single and dual exposure schemes for regular arrays and 2D patterns. For trench printing, we compare the NTD and PTD performance for one-dimensional patterns, line ends and twodimensional structures. We also assess the etch capability and CDU performance of the NTD process. This experimental study proves the added value of the NTD scheme. For contacts and trenches, it allows achieving a broader pitch range and/or smaller litho targets, which makes this process flow attractive for the most advanced lithography applications, including double patterning.
- 11 March 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7640, 764011-764011-12
Printing the metal and contact layers for the 32- and 22-nm node: comparing positive and negative tone development process
A strong demand exists for techniques that can further extend the application of ArF immersion lithography. Besides techniques like litho-friendly design, dual exposure or patterning schemes, customized illumination modes, also alternative processing schemes are viable candidates to reach this goal. One of the most promising alternative process flows uses image reversal by means of a negative tone development (NTD) step with a FUJIFILM solvent-based developer. Traditionally, the printing of contacts and trenches is done by using a dark field mask in combination with positive tone resist and positive tone development. With NTD, the same features can be printed in positive resist using a light field mask, and consequently with a much better image contrast. In this paper, we present an overview of applications for the NTD technique, both for trench and contact patterning, comparing the NTD performance to that of the traditional positive tone development (PTD). This experimental work was performed on an ASML Twinscan XT:1900i scanner at 1.35 NA, and targets the contact/metal layers of the 32 & 22 nm node. For contact hole printing, we consider both single and dual exposure schemes for regular arrays and 2D patterns. For trench printing, we compare the NTD and PTD performance for one-dimensional patterns, line ends and twodimensional structures. We also assess the etch capability and CDU performance of the NTD process. This experimental study proves the added value of the NTD scheme. For contacts and trenches, it allows achieving a broader pitch range and/or smaller litho targets, which makes this process flow attractive for the most advanced lithography applications, including double patterning.