Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jianzhi Xu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • High-Bandwidth Current Shunt With Extremely Low Stray Magnetic Field Based on Thin-Film Resistors

    by Jianzhi Xu, Lifang Yi, Woongkul Lee, Jinyeong Moon

    The use of wide bandgap (WBG) devices introduces higher frequency components into power electronics due to increased switching speeds. To achieve reliable measurement of these high-frequency components in power electronics, high-bandwidth voltage and current probes are essential. While 1 GHz bandwidth voltage probes are commercially available, current probes are typically limited to below 200 MHz. A resistive current sensor, often called a current shunt, converts magnetic field measurement into electric potential measurement, enabling us to use well-established gigahertz-level voltage probes. The overall structure must have an extremely low level of stray magnetic field to minimize parasitic inductance and hence to increase the measurement bandwidth. This article proposes a novel coaxial structure based on thin-film resistors for current shunts. ANSYS Q3D and high-frequency structure simulator (HFSS) simulations demonstrate that this structure effectively cancels magnetic fields along various axes, leading to nearly nonexistent stray fields outside the structure and significantly minimizing parasitic inductance. Experimental results from a prototype with a bandwidth of up to 2.063 GHz validate the proposed design.

  • Open Access

    Characteristics of Collagen Changes in Small Intestine Anastomoses Induced by High-Frequency Electric Field Welding

    by Caihui Zhu, Li Yin, Jianzhi Xu, Xingjian Yang, Hao Wang, Xiaowei Xiang, Haotian Liu, Kefu Liu

    High-frequency electric field welding-induced tissue fusion has been explored as an advanced surgical method for intestinal anastomoses; however, intrinsic mechanisms remain unclear. The aim of this study was to investigate microcosmic changes of collagen within the fusion area, with various parameters. Ex vivo small intestine was fused with mucosa–mucosa. Four levels of compressive pressure (100 kPa, 150 kPa, 200 kPa, 250 kPa) were applied for 10 s in order to fuse the colons under a power level of 140 W. Then, collagen fibers of the fusion area were examined by fibrillar collagen alignment and TEM. Three levels of power (90 W, 110 W, 140 W) and three levels of time (5 s, 10 s, 20 s) were applied in order to fuse colons at 250 kPa, and then collagen within the fusion area was examined by Raman spectroscopy. Fibrillar collagen alignment analysis showed that with the increase in compression pressure, alignment of the collagen in the fusion area gradually increased, and the arrangement of collagen fibers tended to be consistent, which was conducive to the adhesion of collagen fibers. TEM showed that pressure changed the distribution and morphology of collagen fibers. Raman spectroscopy showed that increased power and time within a certain range contributed to collagen cross linking. Peak positions of amide I band and amide III band changed. These results suggested that higher power and a longer amount of time resulted in a decrease in non-reducible cross links and an increase in reducible cross links. Compression pressure, power, and time can affect the state of collagen, but the mechanisms are different. Compressive pressure affected the state of collagen by changing its orientation; power and time denatured collagen by increasing temperature and improved the reducible cross linking of collagen to promote tissue fusion.


  • Open Access

    Analysis and Parameter Design of SiC-Based Current Source Inverter (CSI)

    by Xingjian Yang, Zhennan Zhao, Cheng Wang, Jianzhi Xu, Kefu Liu, Jian Qiu

    Current source inverters (CSIs) use inductors as the major component to store energy. Compared with voltage source inverters (VSIs), CSIs have two advantages: 1. They can avoid the converter failure caused by capacitor failures, and 2. The load current does not increase with load mutation or even short-circuit failure. Therefore, CSIs can be a promising technology for EV charging. However, the waveforms, parameter design procedure, and power efficiency are still unclear. Therefore, it is unclear if CSIs are suitable for EV chargers. This article derives the closed-loop equations of the critical components, including the inductor current waveforms and the voltage ripple. Especially, the load over-voltage phenomenon is derived and verified to further ensure the reliability of the CSI system. Based on the derived equations and reliability requirements, the parameter design procedure is proposed. The power efficiency of both the Si- and SiC-based converters are derived and compared to remove the barrier of applying CSIs in EV chargers in the industry. Our simulations and experiments verify the correctness of the system modeling, over-voltage phenomenon, and power efficiency. All the simulation files (using PLECS) and calculation files (using MATLAB) are attached for the readers to verify and/or further modify.


  • Open Access

    Dynamic Impedance Analysis of Intestinal Anastomosis during High-Frequency Electric Field Welding Process

    by Li Yin, Caihui Zhu, Jianzhi Xu, Hui Zhao, Jian Qiu, Hao Wang, Kefu Liu

    The success rate of the electrosurgical high-frequency electric field welding technique lies in reasonable control of the welding time. However, the final impedance value used to control the welding time varies due to differences in tissue size and the welding method during the welding process. This study aims to introduce a new reference indicator not limited by impedance size from dynamic impedance to achieve an adequate weld strength with minimal thermal damage, providing feedback on the tissue welding effect in medical power supplies. End-to-end anastomosis experiments were conducted with porcine small intestine tissue under seven levels of compression pressure. The dynamic impedance changes were analyzed, combined with compression pressure, temperature, moisture, and collagen during welding. The welding process was divided into three stages according to the dynamic impedance, with impedance decreasing in Period Ⅰ and impedance increasing in Period Ⅲ. Period Ⅲ was the key to high-strength connections due to water evaporation and collagen reorganization. The dynamic impedance ratio is defined as the final impedance divided by the minimum impedance, and successful welding would be predicted when detecting the dynamic impedance ratio over 4 (n = 70, p < 0.001). Dynamic impedance monitoring can be used as a macroscopic real-time prediction of the anastomosis effect.


  • Open Access

    An Inductor-Based and Capacitor-Free Bipolar Pulse Converter with Overvoltage Protection

    by Jianzhi Xu, Xingjian Yang, Hui Zhao, Jian Qiu, Kefu Liu

    The inductor-based and capacitor-free bipolar pulse converter can be applied to electric vehicle charging and realize an efficient and reliable charging-control strategy. Inductor-based converters can avoid the converter failure caused by the failure of energy storage capacitors and improve the reliability. An overvoltage protection scheme based on active clamping topology is used to protect this converter when the load impedance is too large. This overvoltage protection can take effect in an extremely short time (~50 ns) with little energy wasted. Furthermore, mathematical analyses of the proposed topology are presented and simulations based on LTspice are made, showing the feasibility and reliability of this circuit. Moreover, calculation of the power loss on MOSFETs is presented. A 201 W prototype converter with an efficiency of 83% is presented, and experimental results show that the converter can work reliably. This manuscript also proves the feasibility and application prospect of using this current-source-based converter for EV charging.