Killi Sunil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Killi Sunil has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Gokulan Ravindiran
Department of Civil Engineering, Dayananda Sagar College of Engineering, Bengaluru, India
2 shared publications - Kalyani Gaddam
Department of Civil Engineering, Nadimpalli Satyanarayana Raju Institute of Technology, Visakhapatnam 531173, Andhra Pradesh, India
2 shared publications - Ganapathy Ganesh Prabhu
Department of Civil Engineering, GMR Institute of Technology, Rajam, Andhra Pradesh, India
1 shared publication - George Gabriel Vimal Arokiaraj
Department of Civil Engineering, University College of Engineering, Thirukkuvalai, Nagapattinam, Tamilnadu, India
1 shared publication - Panneerselvam Arul Sivanantham
Civil and Architectural Engineering Section, Department of Engineering, University of Technology and Applied Sciences, Muscat, Oman
1 shared publication
Latest Publications
- Open Access
- 24 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-8
Effect of Fibre Aspect-Ratio on the Fresh and Strength Properties of Steel Fibre Reinforced Self-Compacting Concrete
This paper presents the findings of investigation, which was instigated to assess the effects of fibre aspect-ratio on the fresh and mechanical properties of SCC. The investigational parameters were aspect-ratio of the fibre and fibre addition rate. Two different aspect-ratios (64 and 73) of steel fibre were used and the fibre addition rate was between 0.2% and 1.0% with the increment of 0.2% and the fibres were added to the SCC in volume fraction. A series of tests were performed to determine the impact of fibre aspect-ratio and fibre inclusion rate on the engineering/mechanical properties of SCC. The presence of steel fibre in the SCC lessened the workability; furthermore, the upsurge in the inclusion rate of steel fibre abridged the workability further. The inclusion of fibre boosted the compressive strength of the SCC moderately, and conversely, an overwhelming increase in flexural and tensile strength was observed. The rise in the fibre aspect-ratio caused a 2.53% augmentation in the compressive strength of the SCC. Nevertheless, more than 11% improvement in tensile strength was observed, because of the bridging/anchorage established by the fibre. From the obtained results, it can be inferred that the impact of fibre aspect-ratio on the compressive strength of the SCC is not substantial; however, the tensile strength properties of the SCC can be enhanced moderately by increasing the fibre aspect-ratio.
- 24 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-8
Open AccessEffect of Fibre Aspect-Ratio on the Fresh and Strength Properties of Steel Fibre Reinforced Self-Compacting Concrete
This paper presents the findings of investigation, which was instigated to assess the effects of fibre aspect-ratio on the fresh and mechanical properties of SCC. The investigational parameters were aspect-ratio of the fibre and fibre addition rate. Two different aspect-ratios (64 and 73) of steel fibre were used and the fibre addition rate was between 0.2% and 1.0% with the increment of 0.2% and the fibres were added to the SCC in volume fraction. A series of tests were performed to determine the impact of fibre aspect-ratio and fibre inclusion rate on the engineering/mechanical properties of SCC. The presence of steel fibre in the SCC lessened the workability; furthermore, the upsurge in the inclusion rate of steel fibre abridged the workability further. The inclusion of fibre boosted the compressive strength of the SCC moderately, and conversely, an overwhelming increase in flexural and tensile strength was observed. The rise in the fibre aspect-ratio caused a 2.53% augmentation in the compressive strength of the SCC. Nevertheless, more than 11% improvement in tensile strength was observed, because of the bridging/anchorage established by the fibre. From the obtained results, it can be inferred that the impact of fibre aspect-ratio on the compressive strength of the SCC is not substantial; however, the tensile strength properties of the SCC can be enhanced moderately by increasing the fibre aspect-ratio.
- Open Access
- 23 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-8
Experimental Investigation on Reactive Orange 16 Removal Using Waste Biomass of Ulva prolifera
Ulva prolifera marine seaweed was tested for its capacity to eliminate reactive orange 16 (RO16) from aqueous solutions. Algae has recently been regarded as one of the most environmental friendly wastewater treatment methods and resources. The batch study used variations in solution pH, sorbent dosage, initial dye concentration, and temperature. The biochar was characterized using Fourier transform infrared (FT-IR) spectroscopy, an elemental analyser, proximate analysis, and a BET analyser. The adsorption mechanism was further investigated using adsorption isotherm and kinetic models. The thermodynamic analysis was performed by varying temperatures at different dye concentrations and calculating thermodynamic parameters such as Gibbs free energy, enthalpy, and entropy. The study was performed to evaluate the sorbents performance in real-time wastewater treatment, a variety of chemicals, solid-liquid ratios, and regeneration cycles that were used to determine desorption efficiency.
- 23 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-8
Open AccessExperimental Investigation on Reactive Orange 16 Removal Using Waste Biomass of Ulva prolifera
Ulva prolifera marine seaweed was tested for its capacity to eliminate reactive orange 16 (RO16) from aqueous solutions. Algae has recently been regarded as one of the most environmental friendly wastewater treatment methods and resources. The batch study used variations in solution pH, sorbent dosage, initial dye concentration, and temperature. The biochar was characterized using Fourier transform infrared (FT-IR) spectroscopy, an elemental analyser, proximate analysis, and a BET analyser. The adsorption mechanism was further investigated using adsorption isotherm and kinetic models. The thermodynamic analysis was performed by varying temperatures at different dye concentrations and calculating thermodynamic parameters such as Gibbs free energy, enthalpy, and entropy. The study was performed to evaluate the sorbents performance in real-time wastewater treatment, a variety of chemicals, solid-liquid ratios, and regeneration cycles that were used to determine desorption efficiency.
- Open Access
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Removal of Reactive Red 120 in a Batch Technique Using Seaweed‐Based Biochar: A Response Surface Methodology Approach
The elimination of Reactive Red 120 (RR120) from synthetic solution using biochar generated from Ulva prolifera was investigated. The process parameters sorbent dose (A), pH (B), initial dye concentration (C), and temperatures (D) were optimized using response surface methodology (RSM). To estimate the removal effectiveness of dye with the best 27 trails, the Box‐Behnken method (blocked) was utilised. Analysis of variance (ANOVA), main effect plot, interaction plot, and surface plot were used to establish the significance of the model, and the confidence level of the model was set at 95%. To maximise the objective, the RSM optimizer was utilised with a desirability of 1. Furthermore, the batch investigation was supplemented by isotherm models, kinetic models, and thermodynamic analyses to understand the adsorption mechanism.
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Open AccessRemoval of Reactive Red 120 in a Batch Technique Using Seaweed‐Based Biochar: A Response Surface Methodology Approach
The elimination of Reactive Red 120 (RR120) from synthetic solution using biochar generated from Ulva prolifera was investigated. The process parameters sorbent dose (A), pH (B), initial dye concentration (C), and temperatures (D) were optimized using response surface methodology (RSM). To estimate the removal effectiveness of dye with the best 27 trails, the Box‐Behnken method (blocked) was utilised. Analysis of variance (ANOVA), main effect plot, interaction plot, and surface plot were used to establish the significance of the model, and the confidence level of the model was set at 95%. To maximise the objective, the RSM optimizer was utilised with a desirability of 1. Furthermore, the batch investigation was supplemented by isotherm models, kinetic models, and thermodynamic analyses to understand the adsorption mechanism.