George Gabriel Vimal Arokiaraj
Research Subjects
Research Interests
George Gabriel Vimal Arokiaraj has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Panneerselvam Arul Sivanantham
Civil and Architectural Engineering Section, Department of Engineering, University of Technology and Applied Sciences, Muscat, Oman
3 shared publications - Ganapathy Ganesh Prabhu
Department of Civil Engineering, GMR Institute of Technology, Rajam, Andhra Pradesh, India
2 shared publications - Batna Anantha Venkata Ram Kumar
Civil Engineering Department, GMRIT, Rajam, India
1 shared publication - Dasappa Somashekar
Department of Mechanical Engineering, College of Engineering and Technology, Samara University, Samara, Ethiopia
1 shared publication - Elangovan Govindarajalu
University College of Engineering, India
1 shared publication - Killi Sunil
Department of Chemical Engineering, College of Engineering and Technology, Samara University, Afar, Ethiopia
1 shared publication
Latest Publications
- Open Access
- 12 July 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-13
Axial Compression Performance of Concrete-Filled Steel Tubular Columns with Different D/t Ratios
The impacts of three diameter/thickness (D/t) ratios (21.22, 25.46, and 31.83) and concrete strengths (40N/mm2, 50N/mm2, and 60N/mm2) on the strength capabilities of concrete-filled steel tubular (CFST) columns are investigated in this study. The central composite design (CCD) of the response surface methodology (RSM) was used to design the trials in order to complete the tests in a cost-effective manner. 13 (9 distinct tests) columns were evaluated according to the CCD experimental design, and the failure mode of the specimens, loaddeformation behavior, and ultimate strength capacity were investigated. Concrete strength improves, resulting in a decrease in steel tube confinement on the core. Because the steel tube longitudinal compressive stress (fsl) increases as the D/t ratio lowers, the confinement is reduced by inhibiting the circumferential tensile stress (fsc). The Reynolds stress models, analysis of variance (ANOVA), Pareto chart, and contour plot demonstrated that the column D/t ratio, rather than the in-filled concrete strength, has a considerable impact on the CFST columns strength capability. The proposed design models in different international codes and literature were evaluated for their effectiveness in predicting the strength capacities of CFST columns subjected to axial compression load. Using regression analysis, a simple design model was suggested to predict the axial strength capacities of CFST short columns, taking into account material strength and column shape. In comparison to other existing and suggested design models, the proposed design model of the present study delivers a more accurate and stable forecast.
- 12 July 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-13
Open AccessAxial Compression Performance of Concrete-Filled Steel Tubular Columns with Different D/t Ratios
The impacts of three diameter/thickness (D/t) ratios (21.22, 25.46, and 31.83) and concrete strengths (40N/mm2, 50N/mm2, and 60N/mm2) on the strength capabilities of concrete-filled steel tubular (CFST) columns are investigated in this study. The central composite design (CCD) of the response surface methodology (RSM) was used to design the trials in order to complete the tests in a cost-effective manner. 13 (9 distinct tests) columns were evaluated according to the CCD experimental design, and the failure mode of the specimens, loaddeformation behavior, and ultimate strength capacity were investigated. Concrete strength improves, resulting in a decrease in steel tube confinement on the core. Because the steel tube longitudinal compressive stress (fsl) increases as the D/t ratio lowers, the confinement is reduced by inhibiting the circumferential tensile stress (fsc). The Reynolds stress models, analysis of variance (ANOVA), Pareto chart, and contour plot demonstrated that the column D/t ratio, rather than the in-filled concrete strength, has a considerable impact on the CFST columns strength capability. The proposed design models in different international codes and literature were evaluated for their effectiveness in predicting the strength capacities of CFST columns subjected to axial compression load. Using regression analysis, a simple design model was suggested to predict the axial strength capacities of CFST short columns, taking into account material strength and column shape. In comparison to other existing and suggested design models, the proposed design model of the present study delivers a more accurate and stable forecast.
- Open Access
- 24 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-8
Effect of Fibre Aspect-Ratio on the Fresh and Strength Properties of Steel Fibre Reinforced Self-Compacting Concrete
This paper presents the findings of investigation, which was instigated to assess the effects of fibre aspect-ratio on the fresh and mechanical properties of SCC. The investigational parameters were aspect-ratio of the fibre and fibre addition rate. Two different aspect-ratios (64 and 73) of steel fibre were used and the fibre addition rate was between 0.2% and 1.0% with the increment of 0.2% and the fibres were added to the SCC in volume fraction. A series of tests were performed to determine the impact of fibre aspect-ratio and fibre inclusion rate on the engineering/mechanical properties of SCC. The presence of steel fibre in the SCC lessened the workability; furthermore, the upsurge in the inclusion rate of steel fibre abridged the workability further. The inclusion of fibre boosted the compressive strength of the SCC moderately, and conversely, an overwhelming increase in flexural and tensile strength was observed. The rise in the fibre aspect-ratio caused a 2.53% augmentation in the compressive strength of the SCC. Nevertheless, more than 11% improvement in tensile strength was observed, because of the bridging/anchorage established by the fibre. From the obtained results, it can be inferred that the impact of fibre aspect-ratio on the compressive strength of the SCC is not substantial; however, the tensile strength properties of the SCC can be enhanced moderately by increasing the fibre aspect-ratio.
- 24 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-8
Open AccessEffect of Fibre Aspect-Ratio on the Fresh and Strength Properties of Steel Fibre Reinforced Self-Compacting Concrete
This paper presents the findings of investigation, which was instigated to assess the effects of fibre aspect-ratio on the fresh and mechanical properties of SCC. The investigational parameters were aspect-ratio of the fibre and fibre addition rate. Two different aspect-ratios (64 and 73) of steel fibre were used and the fibre addition rate was between 0.2% and 1.0% with the increment of 0.2% and the fibres were added to the SCC in volume fraction. A series of tests were performed to determine the impact of fibre aspect-ratio and fibre inclusion rate on the engineering/mechanical properties of SCC. The presence of steel fibre in the SCC lessened the workability; furthermore, the upsurge in the inclusion rate of steel fibre abridged the workability further. The inclusion of fibre boosted the compressive strength of the SCC moderately, and conversely, an overwhelming increase in flexural and tensile strength was observed. The rise in the fibre aspect-ratio caused a 2.53% augmentation in the compressive strength of the SCC. Nevertheless, more than 11% improvement in tensile strength was observed, because of the bridging/anchorage established by the fibre. From the obtained results, it can be inferred that the impact of fibre aspect-ratio on the compressive strength of the SCC is not substantial; however, the tensile strength properties of the SCC can be enhanced moderately by increasing the fibre aspect-ratio.
- Open Access
- 1 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
A Study on Self‐Consolidate Concrete in Experimental Reinforced‐Concrete Beam Column Structures with Alccofine and Steel Fiber
This paper discusses the concept of self‐consolidating concrete mix with Alccofine‐1203, superplasticizer, viscosity modification agent, crimped steel fiber on the RC beam column joint. Totally, eight reinforced‐concrete (RC) column joints with M25 grade concrete were considered in this study. Out of eight RC beam column joints, two beam column joints served as Alccofine, two beam column joint specimens served as Alccofine 5%, two beam column joint specimens served as Alccofine‐10%, and two beam column joint specimens served as Alccofine‐15%. All the RC beam column joint specimens were tested under the compression until failure in the loading frame of 2000 kN capacity. The test results of Alccofine‐10% showed the higher loading capacity than that of Alccofine‐5% and Alccofine‐15% in self‐consolidating concrete RC beam column joints. The percentage of superplasticizer, viscosity modification agent, and crimped steel fiber is maintained. Nonlinear finite element analysis (FEA) to analyse the beam column joint through nonlinear finite element modelling (NLFEM) and the modelling results were compared from the experimental results. The results obtained through ANSYS modelling show good agreement with the experimented results. The deflection ductility of experimental results shows 1.57, and the predicted deflection ductility shows 1.59 in beam column joint with Alccofine‐10%. ANSYS software is validated as appropriate software to predict the study parameters of self‐consolidation concrete in beam column joints.
- 1 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Open AccessA Study on Self‐Consolidate Concrete in Experimental Reinforced‐Concrete Beam Column Structures with Alccofine and Steel Fiber
This paper discusses the concept of self‐consolidating concrete mix with Alccofine‐1203, superplasticizer, viscosity modification agent, crimped steel fiber on the RC beam column joint. Totally, eight reinforced‐concrete (RC) column joints with M25 grade concrete were considered in this study. Out of eight RC beam column joints, two beam column joints served as Alccofine, two beam column joint specimens served as Alccofine 5%, two beam column joint specimens served as Alccofine‐10%, and two beam column joint specimens served as Alccofine‐15%. All the RC beam column joint specimens were tested under the compression until failure in the loading frame of 2000 kN capacity. The test results of Alccofine‐10% showed the higher loading capacity than that of Alccofine‐5% and Alccofine‐15% in self‐consolidating concrete RC beam column joints. The percentage of superplasticizer, viscosity modification agent, and crimped steel fiber is maintained. Nonlinear finite element analysis (FEA) to analyse the beam column joint through nonlinear finite element modelling (NLFEM) and the modelling results were compared from the experimental results. The results obtained through ANSYS modelling show good agreement with the experimented results. The deflection ductility of experimental results shows 1.57, and the predicted deflection ductility shows 1.59 in beam column joint with Alccofine‐10%. ANSYS software is validated as appropriate software to predict the study parameters of self‐consolidation concrete in beam column joints.
- Open Access
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Comprehensive Characterization of Ferrochrome Slag and Ferrochrome Ash as Sustainable Materials in Construction
Ferrochrome slag (FCS) and ferrochrome ash (FCA) are by‐products generated during the production of ferrochrome alloy in the ferrochrome industry. The use of these by‐products as construction materials appears to be an innovative strategy that could provide numerous environmental and socio‐economic benefits. However, the residual chromium present in ferrochrome by‐products may have some negative effects on the surrounding environment also. In a nutshell, this study provides a thorough and critical examination of ferrochrome slag and ferrochrome ash’s suitability for construction, as well as a list of the major shortcomings that must be addressed to accomplish construction sustainability. A detailed summary of the physical, chemical, and mechanical characteristics of ferrochrome slag and ferrochrome ash was presented in the study. Ferrochrome slag from previous studies is said to exhibit better mechanical properties compared to conventional coarse aggregates which contributed to better mechanical properties of concrete. The application of ferrochrome slag as a substitute for natural sand, on the other hand, is considered to have a detrimental impact. As a reason, further research is necessary to determine the impact of replacing conventional fine aggregate with ferrochrome slag on the various mechanical and durability properties of concrete. Ferrochrome ash from previous studies can be used as a partial replacement for cement and unlike FCS, FCA is nonhazardous since no residual chromium traces were present in FCA. Furthermore, the protracted safety and effect on the surrounding environment of ferrochrome slag containing concrete in a variety of exposure conditions have to be fully examined in the near future.
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Open AccessComprehensive Characterization of Ferrochrome Slag and Ferrochrome Ash as Sustainable Materials in Construction
Ferrochrome slag (FCS) and ferrochrome ash (FCA) are by‐products generated during the production of ferrochrome alloy in the ferrochrome industry. The use of these by‐products as construction materials appears to be an innovative strategy that could provide numerous environmental and socio‐economic benefits. However, the residual chromium present in ferrochrome by‐products may have some negative effects on the surrounding environment also. In a nutshell, this study provides a thorough and critical examination of ferrochrome slag and ferrochrome ash’s suitability for construction, as well as a list of the major shortcomings that must be addressed to accomplish construction sustainability. A detailed summary of the physical, chemical, and mechanical characteristics of ferrochrome slag and ferrochrome ash was presented in the study. Ferrochrome slag from previous studies is said to exhibit better mechanical properties compared to conventional coarse aggregates which contributed to better mechanical properties of concrete. The application of ferrochrome slag as a substitute for natural sand, on the other hand, is considered to have a detrimental impact. As a reason, further research is necessary to determine the impact of replacing conventional fine aggregate with ferrochrome slag on the various mechanical and durability properties of concrete. Ferrochrome ash from previous studies can be used as a partial replacement for cement and unlike FCS, FCA is nonhazardous since no residual chromium traces were present in FCA. Furthermore, the protracted safety and effect on the surrounding environment of ferrochrome slag containing concrete in a variety of exposure conditions have to be fully examined in the near future.