Xiaodong Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaodong Guo has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Jingchen Zhang
National Key Laboratory of Oil and Gas Resources and Engineering, China University of Petroleum (Beijing), Beijing 102249, China
6 shared publications - Shicheng Zhang
State Key Laboratory of Petroleum Resources and Engineering, China University of Petroleum (Beijing), Beijing 102249, China
2 shared publications - Shixin Qiu
College of Petroleum Engineering, China University of Petroleum (Beijing), Beijing 102249, China
2 shared publications - Xiangrui Xi
School of Petroleum Engineering, China University of Petroleum (Beijing), Beijing 102249, China
2 shared publications - Aiguo Hu
Sinopec North China Petroleum Bureau, Zhengzhou 450006, China
1 shared publication - Baocheng Wu
Xinjiang Oilfield Company, Petrochina, Karamay 834000, China
1 shared publication
Latest Publications
- Open Access
Hydraulic Fracture Propagation in Three Meter-Scale Reconstituted Tight Conglomerate Specimens Under Different Formulation Conditions
A tight conglomerate is mechanically heterogeneous because gravel particles, the matrix, and their contacts can perturb hydraulic-fracture paths. This study presents an exploratory comparison of three 2.0 m × 2.0 m × 1.0 m reconstituted conglomerate specimens, identified as specimen 97 (Condition A), specimen 98 (Condition B), and specimen 99 (Condition C). One meter-scale specimen was tested under each formulation condition using the same applied boundary stresses, nominal pumping rate, and fluid viscosity. Post-fracturing surface observations, inlet-pressure histories, and laboratory acoustic-emission (AE) event locations were examined. After event-quality control, DBSCAN-based spatial filtering was performed in Z-score-standardized coordinates, and three-dimensional alpha shapes were constructed from the retained event coordinates in meters to calculate geometric AE-event-envelope volumes. The external surface-fracture traces were more spatially distributed in specimen 97 and more localized in specimen 99. The available DBSCAN–alpha-shape calculation outputs yielded geometric AE-event-envelope volumes of 0.2832, 0.2460, and 0.0937 m3 for specimens 97, 98, and 99, respectively. Because only one specimen was tested under each condition, the specimen formulations and gravel characteristics were not identical, the gravel–matrix interfacial properties were not measured directly, and the pumping histories differed, the observations were interpreted as descriptive case differences rather than as a statistically validated single-factor relationship.
Open AccessHydraulic Fracture Propagation in Three Meter-Scale Reconstituted Tight Conglomerate Specimens Under Different Formulation Conditions
A tight conglomerate is mechanically heterogeneous because gravel particles, the matrix, and their contacts can perturb hydraulic-fracture paths. This study presents an exploratory comparison of three 2.0 m × 2.0 m × 1.0 m reconstituted conglomerate specimens, identified as specimen 97 (Condition A), specimen 98 (Condition B), and specimen 99 (Condition C). One meter-scale specimen was tested under each formulation condition using the same applied boundary stresses, nominal pumping rate, and fluid viscosity. Post-fracturing surface observations, inlet-pressure histories, and laboratory acoustic-emission (AE) event locations were examined. After event-quality control, DBSCAN-based spatial filtering was performed in Z-score-standardized coordinates, and three-dimensional alpha shapes were constructed from the retained event coordinates in meters to calculate geometric AE-event-envelope volumes. The external surface-fracture traces were more spatially distributed in specimen 97 and more localized in specimen 99. The available DBSCAN–alpha-shape calculation outputs yielded geometric AE-event-envelope volumes of 0.2832, 0.2460, and 0.0937 m3 for specimens 97, 98, and 99, respectively. Because only one specimen was tested under each condition, the specimen formulations and gravel characteristics were not identical, the gravel–matrix interfacial properties were not measured directly, and the pumping histories differed, the observations were interpreted as descriptive case differences rather than as a statistically validated single-factor relationship.
- Open Access
- 28 February 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (5) , 2350
Wide-Field Electromagnetic Monitoring of Multi-Cluster Fracture Propagation in Conglomerate Reservoirs: A Field Case from the Baikouquan Formation, Mahu Sag
Multi-stage multi-cluster hydraulic fracturing in conglomerate reservoirs is often characterized by strong cluster-to-cluster variability in fluid distribution, which can reduce stimulation efficiency. However, field-scale observations that constrain how injected fluid is partitioned among clusters remain limited, especially in strongly heterogeneous formations. In this study, wide-field electromagnetic (WFEM) monitoring was applied to a horizontal well completed in the Baikouquan Formation sandstone–conglomerate reservoir of the Mahu Sag, Junggar Basin. The monitored treatment consisted of 13 fracturing stages, each containing six perforation clusters. Time-lapse electromagnetic data acquired during pumping were inverted to reconstruct the spatiotemporal evolution of the effective conductive fluid-swept region. Based on the inversion results, we introduce a set of quantitative proxy indicators (swept area, swept length, cluster-specific sweep, and an asymmetric index) to support relative comparison of fluid distribution patterns at both stage and cluster scales. Results show pronounced non-uniformity within and between stages, even under similar pumping conditions. A limited number of clusters exhibit stronger and farther-reaching WFEM-inferred conductive-fluid responses, whereas other clusters show weaker or more localized responses. Asymmetric sweep patterns on opposite sides of the wellbore are also commonly observed. These patterns are consistent with the combined influences of reservoir heterogeneity, local structural/stress disturbances, and operational factors, although WFEM alone does not uniquely validate causal mechanisms of fracture growth. Overall, this study demonstrates that WFEM monitoring provides a field-scale proxy tool for delineating effective conductive fluid-swept regions and for evaluating cluster-to-cluster variability under consistent acquisition and inversion settings. The findings offer practical guidance for interpreting fluid distribution and optimizing multi-cluster fracturing in strongly heterogeneous unconventional reservoirs.
- 28 February 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (5) , 2350
Open AccessWide-Field Electromagnetic Monitoring of Multi-Cluster Fracture Propagation in Conglomerate Reservoirs: A Field Case from the Baikouquan Formation, Mahu Sag
Multi-stage multi-cluster hydraulic fracturing in conglomerate reservoirs is often characterized by strong cluster-to-cluster variability in fluid distribution, which can reduce stimulation efficiency. However, field-scale observations that constrain how injected fluid is partitioned among clusters remain limited, especially in strongly heterogeneous formations. In this study, wide-field electromagnetic (WFEM) monitoring was applied to a horizontal well completed in the Baikouquan Formation sandstone–conglomerate reservoir of the Mahu Sag, Junggar Basin. The monitored treatment consisted of 13 fracturing stages, each containing six perforation clusters. Time-lapse electromagnetic data acquired during pumping were inverted to reconstruct the spatiotemporal evolution of the effective conductive fluid-swept region. Based on the inversion results, we introduce a set of quantitative proxy indicators (swept area, swept length, cluster-specific sweep, and an asymmetric index) to support relative comparison of fluid distribution patterns at both stage and cluster scales. Results show pronounced non-uniformity within and between stages, even under similar pumping conditions. A limited number of clusters exhibit stronger and farther-reaching WFEM-inferred conductive-fluid responses, whereas other clusters show weaker or more localized responses. Asymmetric sweep patterns on opposite sides of the wellbore are also commonly observed. These patterns are consistent with the combined influences of reservoir heterogeneity, local structural/stress disturbances, and operational factors, although WFEM alone does not uniquely validate causal mechanisms of fracture growth. Overall, this study demonstrates that WFEM monitoring provides a field-scale proxy tool for delineating effective conductive fluid-swept regions and for evaluating cluster-to-cluster variability under consistent acquisition and inversion settings. The findings offer practical guidance for interpreting fluid distribution and optimizing multi-cluster fracturing in strongly heterogeneous unconventional reservoirs.
- Open Access
Large-Scale Mine Experimental Study on the Crack Extension Law of Deep-Seated Coal Rock
Deep-seated coalbed methane (CBM) resources in the Daniudi Gas Field of the Ordos Basin are abundant; however, conventional laboratory-scale hydraulic fracturing experiments are unable to realistically reproduce fracture propagation behavior due to pronounced reservoir heterogeneity and the complex development of bedding and cleat structures. In this study, a self-developed 10,000-ton true triaxial hydraulic fracturing simulation platform was employed to conduct mine-scale experiments using large 2 m × 2 m × 1 m No. 8 coal-rock outcrop specimens. A full-scale steel-casing wellbore and an industrial fracturing fluid system were incorporated to replicate field conditions. Experiments were performed under varying pumping rates (0.2–0.4 m3/min) and fracturing fluid viscosities (10–50 mPa·s). The results indicate that post-failure fractures in deep coal formations primarily develop into complex fracture zones extending vertically from the wellbore. Their morphology is strongly governed by bedding planes and cleats, producing tortuous, banded, and mesh-like patterns. When the fracturing fluid viscosity is maintained between 18 and 27 mPa·s, longitudinal fracture diversion along the wellbore is effectively suppressed, while the increased static pressure promotes the activation of natural fractures. Increasing the pumping rate to 0.4 m3/min markedly enhances the stimulated reservoir volume (SRV), with an increase of approximately 1354%, and significantly increases fracture branch density. However, higher viscosities (>27 mPa·s), despite promoting fracture complexity, reduce proppant transport efficiency due to increased in-fracture tortuosity. This study quantitatively characterizes the coupled responses of fracture volume fraction, branch density, and fracture-surface roughness, and elucidates the interplay between displacement and viscosity in governing fracture network evolution. The findings provide an important experimental foundation for optimizing hydraulic fracturing parameters in the efficient development of deep-seated CBM reservoirs.
Open AccessLarge-Scale Mine Experimental Study on the Crack Extension Law of Deep-Seated Coal Rock
Deep-seated coalbed methane (CBM) resources in the Daniudi Gas Field of the Ordos Basin are abundant; however, conventional laboratory-scale hydraulic fracturing experiments are unable to realistically reproduce fracture propagation behavior due to pronounced reservoir heterogeneity and the complex development of bedding and cleat structures. In this study, a self-developed 10,000-ton true triaxial hydraulic fracturing simulation platform was employed to conduct mine-scale experiments using large 2 m × 2 m × 1 m No. 8 coal-rock outcrop specimens. A full-scale steel-casing wellbore and an industrial fracturing fluid system were incorporated to replicate field conditions. Experiments were performed under varying pumping rates (0.2–0.4 m3/min) and fracturing fluid viscosities (10–50 mPa·s). The results indicate that post-failure fractures in deep coal formations primarily develop into complex fracture zones extending vertically from the wellbore. Their morphology is strongly governed by bedding planes and cleats, producing tortuous, banded, and mesh-like patterns. When the fracturing fluid viscosity is maintained between 18 and 27 mPa·s, longitudinal fracture diversion along the wellbore is effectively suppressed, while the increased static pressure promotes the activation of natural fractures. Increasing the pumping rate to 0.4 m3/min markedly enhances the stimulated reservoir volume (SRV), with an increase of approximately 1354%, and significantly increases fracture branch density. However, higher viscosities (>27 mPa·s), despite promoting fracture complexity, reduce proppant transport efficiency due to increased in-fracture tortuosity. This study quantitatively characterizes the coupled responses of fracture volume fraction, branch density, and fracture-surface roughness, and elucidates the interplay between displacement and viscosity in governing fracture network evolution. The findings provide an important experimental foundation for optimizing hydraulic fracturing parameters in the efficient development of deep-seated CBM reservoirs.
- Open Access
Capillary–Viscoelastic Coupling and Multiscale Imbibition Dynamics in Tight Conglomerate Rocks
Tight conglomerate reservoirs exhibit strong pore-scale heterogeneity and extremely low permeability, in which spontaneous imbibition is primarily governed by capillary and viscoelastic effects. In this study, the imbibition dynamics of four representative fracturing fluid systems, including slickwater, 3% potassium chloride (KCl) brine, hydrolyzed polyacrylamide (HPAM) viscoelastic fluid, and a nanoemulsion (NE), were investigated using a temperature-controlled nuclear magnetic resonance (NMR) monitoring system. This approach enables real-time quantification of fluid uptake and pore-scale redistribution through time-resolved T2 spectral analysis. The experimental results reveal a three-stage imbibition process consisting of rapid capillary-driven uptake, viscoelastic-retarded transition, and final equilibrium. Among the four fracturing fluid systems, the nanoemulsion exhibits the lowest interfacial tension (1.72 mN/m), the strongest wettability alteration, and the highest equilibrium recovery (0.76), which is nearly 80% greater than that of slickwater. Based on these observations, a multiscale capillary–viscoelastic coupling model was developed by extending the Lucas–Washburn framework to incorporate pore-size distribution, time-dependent wettability evolution, and viscoelastic damping. The model fits the experimental data well (R2 > 0.90) and identifies viscosity as the most influential parameter controlling the imbibition rate (sensitivity = 0.78). Energy analysis further indicates that capillary energy dominates the early stage, whereas viscoelastic energy storage sustains fluid transport during the later stage. SEM observations were further used to qualitatively corroborate pore heterogeneity and pore–mineral associations, supporting the NMR-based pore-scale interpretation. This study provides a quantitative framework for describing non-Newtonian capillary flow in tight conglomerate rocks and enhances the understanding of capillary–viscoelastic interactions relevant to multiphase fluid migration.
Open AccessCapillary–Viscoelastic Coupling and Multiscale Imbibition Dynamics in Tight Conglomerate Rocks
Tight conglomerate reservoirs exhibit strong pore-scale heterogeneity and extremely low permeability, in which spontaneous imbibition is primarily governed by capillary and viscoelastic effects. In this study, the imbibition dynamics of four representative fracturing fluid systems, including slickwater, 3% potassium chloride (KCl) brine, hydrolyzed polyacrylamide (HPAM) viscoelastic fluid, and a nanoemulsion (NE), were investigated using a temperature-controlled nuclear magnetic resonance (NMR) monitoring system. This approach enables real-time quantification of fluid uptake and pore-scale redistribution through time-resolved T2 spectral analysis. The experimental results reveal a three-stage imbibition process consisting of rapid capillary-driven uptake, viscoelastic-retarded transition, and final equilibrium. Among the four fracturing fluid systems, the nanoemulsion exhibits the lowest interfacial tension (1.72 mN/m), the strongest wettability alteration, and the highest equilibrium recovery (0.76), which is nearly 80% greater than that of slickwater. Based on these observations, a multiscale capillary–viscoelastic coupling model was developed by extending the Lucas–Washburn framework to incorporate pore-size distribution, time-dependent wettability evolution, and viscoelastic damping. The model fits the experimental data well (R2 > 0.90) and identifies viscosity as the most influential parameter controlling the imbibition rate (sensitivity = 0.78). Energy analysis further indicates that capillary energy dominates the early stage, whereas viscoelastic energy storage sustains fluid transport during the later stage. SEM observations were further used to qualitatively corroborate pore heterogeneity and pore–mineral associations, supporting the NMR-based pore-scale interpretation. This study provides a quantitative framework for describing non-Newtonian capillary flow in tight conglomerate rocks and enhances the understanding of capillary–viscoelastic interactions relevant to multiphase fluid migration.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Three-dimensional reconstruction of rough fractures and numerical simulation of proppant transport in tight conglomerate
Tight conglomerate reservoirs exhibit strong heterogeneity and complex stress–rock coupling. Hydraulic fractures form tortuous paths due to gravel interactions, complicating proppant migration and placement. Traditional smooth-plate models fail to capture real fracture features. This study uses large-scale true triaxial tests to generate fractures, three-dimensional (3D) scanning for digital reconstruction, and quantitative surface characterization. A Discrete Element Method-Computational Fluid Dynamics fluid–solid coupling model analyzes the effects of gravel content, proppant combinations, injection velocity, and branch fractures on proppant behavior. Results show: (1) Gravel-induced deflection/penetration increases roughness, raising proppant coverage by 8.99% and dune height by 15.61 mm, but hinders distal transport and accelerates settling; (2) mixed-size proppant causes “bridging;” a “small-to-large” sequence reduces blockage risk; (3) increasing injection velocity from 0.1 to 0.4 m/s cuts proppant coverage by 80.5% and dune height by 19.06 mm; near-wellbore filling suffers due to turbulence despite a longer migration distance; (4) branch fractures accelerate sedimentation and elevate the main fracture dune by approximately 8.85 mm, moderate velocity increases help; (5) mixed-size proppant improves sedimentation and packing; smaller particles (>50%) effectively fill voids. The proposed 3D reconstruction and multi-factor fluid–solid model offer theoretical guidance for optimizing fracturing in conglomerate reservoirs, enhancing conductivity and field performance.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Three-dimensional reconstruction of rough fractures and numerical simulation of proppant transport in tight conglomerate
Tight conglomerate reservoirs exhibit strong heterogeneity and complex stress–rock coupling. Hydraulic fractures form tortuous paths due to gravel interactions, complicating proppant migration and placement. Traditional smooth-plate models fail to capture real fracture features. This study uses large-scale true triaxial tests to generate fractures, three-dimensional (3D) scanning for digital reconstruction, and quantitative surface characterization. A Discrete Element Method-Computational Fluid Dynamics fluid–solid coupling model analyzes the effects of gravel content, proppant combinations, injection velocity, and branch fractures on proppant behavior. Results show: (1) Gravel-induced deflection/penetration increases roughness, raising proppant coverage by 8.99% and dune height by 15.61 mm, but hinders distal transport and accelerates settling; (2) mixed-size proppant causes “bridging;” a “small-to-large” sequence reduces blockage risk; (3) increasing injection velocity from 0.1 to 0.4 m/s cuts proppant coverage by 80.5% and dune height by 19.06 mm; near-wellbore filling suffers due to turbulence despite a longer migration distance; (4) branch fractures accelerate sedimentation and elevate the main fracture dune by approximately 8.85 mm, moderate velocity increases help; (5) mixed-size proppant improves sedimentation and packing; smaller particles (>50%) effectively fill voids. The proposed 3D reconstruction and multi-factor fluid–solid model offer theoretical guidance for optimizing fracturing in conglomerate reservoirs, enhancing conductivity and field performance.
- Open Access
Simulation and Analysis of Proppant Transport Patterns in Wellbore-Fracture Systems
Staged multi-cluster fracturing of horizontal wells is one of the most important tools to achieve efficient development of unconventional oil and gas reservoirs. The multi-stage fracturing technique forms complex fractures with multiple clusters and branches in the formation, causing competing diversions leading to more complex proppant transport patterns, and the proppant placement method determines the flow conductivity of complex fractures, so it is necessary to investigate the proppant transport patterns in complex fractures. To address this issue, a field-scale geometric model is established for numerical simulation, and the multiphase flow diversion pattern in the wellbore, the proppant distribution pattern under different network conditions, and the optimization of different construction parameters are investigated. The results are obtained as follows: the distribution of solid and liquid phases in each cluster of the well conforms to the trend of variable mass flow; the proppant is distributed at the heel end in multiple clusters of fractures, and the sand and liquid are unevenly distributed among clusters of fractures, and the number of branching affects the proppant transport; through sensitivity analysis of the influencing factors, the pumping displacement, fracturing fluid viscosity and proppant particle size are optimized, and the construction parameters of 14 m3/min, 5 mPa·s, 70/140 mesh, 12% sand ratio are determined. This study has a certain guiding significance for the optimization of fracturing parameters in this block.
Open AccessSimulation and Analysis of Proppant Transport Patterns in Wellbore-Fracture Systems
Staged multi-cluster fracturing of horizontal wells is one of the most important tools to achieve efficient development of unconventional oil and gas reservoirs. The multi-stage fracturing technique forms complex fractures with multiple clusters and branches in the formation, causing competing diversions leading to more complex proppant transport patterns, and the proppant placement method determines the flow conductivity of complex fractures, so it is necessary to investigate the proppant transport patterns in complex fractures. To address this issue, a field-scale geometric model is established for numerical simulation, and the multiphase flow diversion pattern in the wellbore, the proppant distribution pattern under different network conditions, and the optimization of different construction parameters are investigated. The results are obtained as follows: the distribution of solid and liquid phases in each cluster of the well conforms to the trend of variable mass flow; the proppant is distributed at the heel end in multiple clusters of fractures, and the sand and liquid are unevenly distributed among clusters of fractures, and the number of branching affects the proppant transport; through sensitivity analysis of the influencing factors, the pumping displacement, fracturing fluid viscosity and proppant particle size are optimized, and the construction parameters of 14 m3/min, 5 mPa·s, 70/140 mesh, 12% sand ratio are determined. This study has a certain guiding significance for the optimization of fracturing parameters in this block.
- Open Access
Field-Scale Experimental Study on the Perforation Erosion in Horizontal Wellbore under Real Fracturing Conditions
Limited-entry fracturing (LEF) technology is a widely used method to realize the simultaneous propagation of multiple fractures in horizontal wells. The key of this technology is to create high perforation friction to maintain the high treatment pressure in the wellbore and realize the uniform fluid entry of multi-fractures; however, high perforation friction cannot be effectively maintained due to the serious perforation erosion effect. Considering that the current laboratory studies mostly used small fluid injection flowrate, low injection pressure, and small proppant dosage, this study has developed a field-scale flow system to investigate the effect of various factors on perforation erosion under real field conditions. The filed-scale flow system uses the real fracturing trucks, proppant, and perforated wellbore, the fluid flow rate through perforation could reach 200 m/s and the injection pressure could reach 105 MPa. The effects of different parameters, such as injection flow rates, proppant concentration, proppant type, proppant size, and carrying fluid viscosity, on the perforation erosion were investigated. The experimental results show that: (1) The perforation friction during erosion goes through two stages, i.e., the roundness erosion stage and the diameter erosion stage. The reduction of perforating friction mainly occurred in the first stage, which was completed after injecting 1 m3 proppant. (2) After erosion, the perforation changes from the original circular shape to a trumpet shape, the inner diameter is much larger than the outer diameter. (3) The more serious perforation erosion is caused by the conditions of high injection flow rate, large proppant size, using ceramic proppant, and low viscosity fluid. The findings of this study can help for a better understanding of perforation erosion during the limited-entry fracturing in the horizontal wells, and also could promote the establishment of a theoretical model of perforation erosion under the field-scale conditions.
Open AccessField-Scale Experimental Study on the Perforation Erosion in Horizontal Wellbore under Real Fracturing Conditions
Limited-entry fracturing (LEF) technology is a widely used method to realize the simultaneous propagation of multiple fractures in horizontal wells. The key of this technology is to create high perforation friction to maintain the high treatment pressure in the wellbore and realize the uniform fluid entry of multi-fractures; however, high perforation friction cannot be effectively maintained due to the serious perforation erosion effect. Considering that the current laboratory studies mostly used small fluid injection flowrate, low injection pressure, and small proppant dosage, this study has developed a field-scale flow system to investigate the effect of various factors on perforation erosion under real field conditions. The filed-scale flow system uses the real fracturing trucks, proppant, and perforated wellbore, the fluid flow rate through perforation could reach 200 m/s and the injection pressure could reach 105 MPa. The effects of different parameters, such as injection flow rates, proppant concentration, proppant type, proppant size, and carrying fluid viscosity, on the perforation erosion were investigated. The experimental results show that: (1) The perforation friction during erosion goes through two stages, i.e., the roundness erosion stage and the diameter erosion stage. The reduction of perforating friction mainly occurred in the first stage, which was completed after injecting 1 m3 proppant. (2) After erosion, the perforation changes from the original circular shape to a trumpet shape, the inner diameter is much larger than the outer diameter. (3) The more serious perforation erosion is caused by the conditions of high injection flow rate, large proppant size, using ceramic proppant, and low viscosity fluid. The findings of this study can help for a better understanding of perforation erosion during the limited-entry fracturing in the horizontal wells, and also could promote the establishment of a theoretical model of perforation erosion under the field-scale conditions.