Linsen Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Linsen Huang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Jinghua Ji
Jiangsu University
7 shared publications - Wenxiang Zhao
Nanjing Institute of Technology
7 shared publications Tao Tao
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang, China
3 shared publications- Hongyu Tang
School of Electrical and Information, Zhenjiang College, Zhenjiang 212028, China
2 shared publications - Yuxuan Du
School of Automation, Nanjing Institute of Technology, Nanjing, China
2 shared publications - Dao Zhou
AAU Energy, Aalborg University, Aalborg, Denmark
1 shared publication
Latest Publications
- 17 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 38 (3) , 2211-2222
Enhanced Fault Tolerance of Dual Three-Phase Permanent Magnet Motor With Three-Redundancy Control
This article proposes a novel three-redundancy control for the dual three-phase permanent magnet (DTP-PM) motor to enhance the open-phase fault tolerance. Three redundancies can be operated individually or synergistically. Hence, the faulty redundancy can be disconnected from the system to address the open-phase fault. The fault tolerance can be significantly enhanced. Primarily, the structure of the DTP-PM motor is analyzed. Six phases of the DTP-PM motor are separated into three sets of orthogonal phases and considered three two-phase motors. Therefore, three redundancies can be established. Since orthogonal phases provide a balanced structure, the magnetomotive force of each redundancy can be well controlled. Then, a DTP-PM motor control system with three redundancies is established, and a potential topology for the proposed strategy is also illustrated. Furthermore, the basic voltage vectors for each redundancy are investigated. The reference voltage vectors can be modulated expediently. Finally, some simulations and experiments are carried out, validating the feasibility and effectiveness of the proposed strategy.
- 17 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 38 (3) , 2211-2222
Enhanced Fault Tolerance of Dual Three-Phase Permanent Magnet Motor With Three-Redundancy Control
This article proposes a novel three-redundancy control for the dual three-phase permanent magnet (DTP-PM) motor to enhance the open-phase fault tolerance. Three redundancies can be operated individually or synergistically. Hence, the faulty redundancy can be disconnected from the system to address the open-phase fault. The fault tolerance can be significantly enhanced. Primarily, the structure of the DTP-PM motor is analyzed. Six phases of the DTP-PM motor are separated into three sets of orthogonal phases and considered three two-phase motors. Therefore, three redundancies can be established. Since orthogonal phases provide a balanced structure, the magnetomotive force of each redundancy can be well controlled. Then, a DTP-PM motor control system with three redundancies is established, and a potential topology for the proposed strategy is also illustrated. Furthermore, the basic voltage vectors for each redundancy are investigated. The reference voltage vectors can be modulated expediently. Finally, some simulations and experiments are carried out, validating the feasibility and effectiveness of the proposed strategy.
- 28 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (2) , 2285-2294
Decoupled Fault-Tolerant Model Predictive Current Control for Dual Three-Phase PMSMs With Harmonic Compensation
This article proposes a decoupled fault-tolerant model predictive current control for a dual three-phase permanent magnet synchronous motor with harmonic compensation. The harmonics caused by nonsinusoidal back electromotive force can be well controlled under the open-circuit fault scenario by designing a harmonic closed-loop scheme. First, a decoupled predictive model and fault-tolerant voltage vectors are deduced based on a reduced-dimension matrix, which can eliminate the coupling issues between the harmonic and fundamental subspaces. Afterward, a uniform harmonic-free virtual vector is constructed by rearranging the irregular voltage vectors. More importantly, a virtual null vector is designed in the scheme, where the virtual null vector is effective in the harmonic subspace and has no components in the fundamental subspace. So, the harmonics can be further controlled without affecting torque and flux generation. Extensive experimental results verify the effectiveness of the proposed method.
- 28 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (2) , 2285-2294
Decoupled Fault-Tolerant Model Predictive Current Control for Dual Three-Phase PMSMs With Harmonic Compensation
This article proposes a decoupled fault-tolerant model predictive current control for a dual three-phase permanent magnet synchronous motor with harmonic compensation. The harmonics caused by nonsinusoidal back electromotive force can be well controlled under the open-circuit fault scenario by designing a harmonic closed-loop scheme. First, a decoupled predictive model and fault-tolerant voltage vectors are deduced based on a reduced-dimension matrix, which can eliminate the coupling issues between the harmonic and fundamental subspaces. Afterward, a uniform harmonic-free virtual vector is constructed by rearranging the irregular voltage vectors. More importantly, a virtual null vector is designed in the scheme, where the virtual null vector is effective in the harmonic subspace and has no components in the fundamental subspace. So, the harmonics can be further controlled without affecting torque and flux generation. Extensive experimental results verify the effectiveness of the proposed method.
- Open Access
- 1 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (12) , 15356-15369
A Modified Flux Observer for Sensorless Direct Torque Control of Dual Three-Phase PMSM Considering Open-Circuit Fault
This article proposes a modified flux observer for sensorless direct torque control (DTC) of the dual three-phase permanent-magnet synchronous motor. The proposed method can improve torque performance without a position sensor. The flux observer is proposed to obtain the stator fluxes and rotor fluxes. The stator fluxes can be utilized to calculate the amplitude of torque and flux for DTC system. Meanwhile, the position information can be detected from the rotor fluxes by using a normalized phase-locked loop. This new flux observer can overcome the disadvantages due to the dc bias, initial value, and harmonic components. The stability of the proposed observer is also analyzed in this article. In addition, a fault-tolerant DTC scheme for open-circuit fault is introduced. The performances of torque control and position estimation are evaluated under healthy, open-circuit fault, and fault-tolerant conditions. Simulation and experimental evaluation are carried out to confirm the effectiveness of the proposed sensorless DTC scheme.
- 1 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (12) , 15356-15369
Open AccessA Modified Flux Observer for Sensorless Direct Torque Control of Dual Three-Phase PMSM Considering Open-Circuit Fault
This article proposes a modified flux observer for sensorless direct torque control (DTC) of the dual three-phase permanent-magnet synchronous motor. The proposed method can improve torque performance without a position sensor. The flux observer is proposed to obtain the stator fluxes and rotor fluxes. The stator fluxes can be utilized to calculate the amplitude of torque and flux for DTC system. Meanwhile, the position information can be detected from the rotor fluxes by using a normalized phase-locked loop. This new flux observer can overcome the disadvantages due to the dc bias, initial value, and harmonic components. The stability of the proposed observer is also analyzed in this article. In addition, a fault-tolerant DTC scheme for open-circuit fault is introduced. The performances of torque control and position estimation are evaluated under healthy, open-circuit fault, and fault-tolerant conditions. Simulation and experimental evaluation are carried out to confirm the effectiveness of the proposed sensorless DTC scheme.
- 3 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (4) , 2385-2397
Direct Torque Control for Dual Three-Phase Permanent Magnet Motor With Improved Torque and Flux
The conventional duty ratio modulation based direct torque control (DR-DTC) for the dual three-phase permanent magnet (DTP-PM) motor reduces the torque ripple using duty ratio modulation in torque control. However, the flux was controlled by a hysteresis comparator, resulting in deficient steady-state performance. This paper proposes a novel DR-DTC strategy to improve torque and flux simultaneously. Firstly, a switching table with the multiple vector selection is newly established. Two adjacent virtual voltage vectors and a null vector are selected in each control period. Then, the duty ratios of selected adjacent virtual voltage vectors are optimized with the dual objective modulation considering torque performance and flux performance. In addition, the combination of adjacent virtual voltage vectors for the DTP-PM motor generates non-standard symmetrical switching sequences. Two switching sequences generated methods are further investigated to address the issue. So, the switching sequences of the proposed strategy can also be generated easily. Finally, the conventional strategy and the proposed strategy are compared through experiments, and the experimental results verify the effectiveness of the proposed strategy.
- 3 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (4) , 2385-2397
Direct Torque Control for Dual Three-Phase Permanent Magnet Motor With Improved Torque and Flux
The conventional duty ratio modulation based direct torque control (DR-DTC) for the dual three-phase permanent magnet (DTP-PM) motor reduces the torque ripple using duty ratio modulation in torque control. However, the flux was controlled by a hysteresis comparator, resulting in deficient steady-state performance. This paper proposes a novel DR-DTC strategy to improve torque and flux simultaneously. Firstly, a switching table with the multiple vector selection is newly established. Two adjacent virtual voltage vectors and a null vector are selected in each control period. Then, the duty ratios of selected adjacent virtual voltage vectors are optimized with the dual objective modulation considering torque performance and flux performance. In addition, the combination of adjacent virtual voltage vectors for the DTP-PM motor generates non-standard symmetrical switching sequences. Two switching sequences generated methods are further investigated to address the issue. So, the switching sequences of the proposed strategy can also be generated easily. Finally, the conventional strategy and the proposed strategy are compared through experiments, and the experimental results verify the effectiveness of the proposed strategy.
- 22 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 11085-11097
Remedial Direct Torque Control for Dual Three-Phase Permanent-Magnet Motor With Harmonic Torque Suppression
This article proposes a novel remedial direct torque control (RDTC) for the postfault operation of the dual three-phase permanent-magnet (DTP-PM) motor. The DTP-PM motor is configured as a two-neutral points model and fed by an eight-leg voltage source inverter. Also, the harmonic torque induced by the third harmonic back electromotive force and zero-sequence currents is considered at the postfault operation. First, the switching tables for different fault conditions are pre-established. The proposed strategy can be applied to different postfault operations with one phase open by replacing the switching table simply. At the normal operation, the redundant auxiliary legs are disabled. So, the proposed eight-leg voltage inverter is the same as the conventional six-leg one. At the postfault operation, the auxiliary leg in the faulty three-phase windings provides an additional control degree of freedom. Hence, the fault-tolerant capability of the DTP-PM motor with two neutral points can be enhanced. Also, the proposed strategy compensates for the harmonic torque by modifying the reference torque. Based on the proposed RDTC, the postfault operational performance can be significantly improved. Finally, the simulations and experiments are conducted to validate the feasibility of the proposed strategy.
- 22 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 11085-11097
Remedial Direct Torque Control for Dual Three-Phase Permanent-Magnet Motor With Harmonic Torque Suppression
This article proposes a novel remedial direct torque control (RDTC) for the postfault operation of the dual three-phase permanent-magnet (DTP-PM) motor. The DTP-PM motor is configured as a two-neutral points model and fed by an eight-leg voltage source inverter. Also, the harmonic torque induced by the third harmonic back electromotive force and zero-sequence currents is considered at the postfault operation. First, the switching tables for different fault conditions are pre-established. The proposed strategy can be applied to different postfault operations with one phase open by replacing the switching table simply. At the normal operation, the redundant auxiliary legs are disabled. So, the proposed eight-leg voltage inverter is the same as the conventional six-leg one. At the postfault operation, the auxiliary leg in the faulty three-phase windings provides an additional control degree of freedom. Hence, the fault-tolerant capability of the DTP-PM motor with two neutral points can be enhanced. Also, the proposed strategy compensates for the harmonic torque by modifying the reference torque. Based on the proposed RDTC, the postfault operational performance can be significantly improved. Finally, the simulations and experiments are conducted to validate the feasibility of the proposed strategy.
- 27 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10681-10689
Simplified Three-Vector-Based Model Predictive Thrust Force Control With Cascaded Optimization Process for a Double-Side Linear Vernier Permanent Magnet Motor
In order to reduce thrust force and stator flux ripples, this paper proposes a simplified three-vector-based model predictive thrust force control (MPTFC) method for a double-side linear vernier permanent magnet motor. First, a simplified control set is designed to select two active voltage vectors (VVs) in the prediction stage, instead of evaluating redundant VVs. Null VVs are applied to adjust the amplitude of the modified VV, which can realize a full range modulation by the predefined cost function. To simplify the tuning work of the weighting factor, the variables in the cost function only consider the stator flux term. Then, the duration time of the selected VVs are distributed reasonably through a novel cascaded optimization process. Also, the deadbeat principle is adopted to calculate the duty cycle. With the proposed method, the thrust force and stator flux ripples can be considerably minimized. The simulated and experimental results are conducted to verify the proposed control method.
- 27 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10681-10689
Simplified Three-Vector-Based Model Predictive Thrust Force Control With Cascaded Optimization Process for a Double-Side Linear Vernier Permanent Magnet Motor
In order to reduce thrust force and stator flux ripples, this paper proposes a simplified three-vector-based model predictive thrust force control (MPTFC) method for a double-side linear vernier permanent magnet motor. First, a simplified control set is designed to select two active voltage vectors (VVs) in the prediction stage, instead of evaluating redundant VVs. Null VVs are applied to adjust the amplitude of the modified VV, which can realize a full range modulation by the predefined cost function. To simplify the tuning work of the weighting factor, the variables in the cost function only consider the stator flux term. Then, the duration time of the selected VVs are distributed reasonably through a novel cascaded optimization process. Also, the deadbeat principle is adopted to calculate the duty cycle. With the proposed method, the thrust force and stator flux ripples can be considerably minimized. The simulated and experimental results are conducted to verify the proposed control method.
- 15 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (1) , 116-127
A Generalized Mesh-Based Thermal Network Model for SPM Machines Combining Coupled Winding Solution
This paper proposes a new equivalent thermal network (ETN) model for surface-mounted permanent magnet (SPM) machines by applying a mesh-based method with bi-directional coupled winding solution. The key is to couple the winding temperature distributions with thermal network meshes in stator dynamically. First, the meshing method is proposed and combined in the lumped parameter thermal model to obtain temperature distributions instead of the average temperature. The mesh elements have identical shapes and unified thermal conductivity, which can greatly enhance the modeling flexibility and efficiency. Second, the slot-winding is established by a 2-D analytical solution method under segmented boundaries with temperature gradient. Then, the winding solution is coupled with mesh nodes and integrated in ETN model to accurately predict temperature distributions in slot including the maximum temperature and position offset. Finally, the effectiveness of the proposed ETN model is verified by comparison with finite-element analysis and experimental results.
- 15 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (1) , 116-127
A Generalized Mesh-Based Thermal Network Model for SPM Machines Combining Coupled Winding Solution
This paper proposes a new equivalent thermal network (ETN) model for surface-mounted permanent magnet (SPM) machines by applying a mesh-based method with bi-directional coupled winding solution. The key is to couple the winding temperature distributions with thermal network meshes in stator dynamically. First, the meshing method is proposed and combined in the lumped parameter thermal model to obtain temperature distributions instead of the average temperature. The mesh elements have identical shapes and unified thermal conductivity, which can greatly enhance the modeling flexibility and efficiency. Second, the slot-winding is established by a 2-D analytical solution method under segmented boundaries with temperature gradient. Then, the winding solution is coupled with mesh nodes and integrated in ETN model to accurately predict temperature distributions in slot including the maximum temperature and position offset. Finally, the effectiveness of the proposed ETN model is verified by comparison with finite-element analysis and experimental results.