Alexey Vladimirovich Aleshkin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexey Vladimirovich Aleshkin has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Peter Alexeyevich Savinykh
GNU NIISH-SH North-East Scientific and Research Institute of Agriculture N.V. Rudnitshy , Kirov , Russia
3 shared publications - Alexey Yu. Isupov
Federal Agricultural Research Center of the North-East named N. V. Rudnitsky
2 shared publications - Fedor Aleksandrovich Kipriyanov
Vologda State Dairy Farming Academy by N.V. Vereshchagin
2 shared publications - Vladimir N. Nechaev
Нижегородский государственный инженерно-экономический университет
2 shared publications - Nikolay Valentinovich Turubanov
Federal Agricultural Research Center of the North-East named N. V. Rudnitsky
1 shared publication - Petr Savinykh
Federal Agrarian Science Center of the North-East Region
1 shared publication
Latest Publications
- 9 August 2026
- Published by ECO-Vector LLC (Publications) in Tractors and Agricultural Machinery
- Vol. 93 (3) , 289-300
Experimental-mathematical justification of criterion of grain micronization
BACKGROUND: During the micronization process, grain separation is necessary for those, the heating-up of which was insufficient. Considering the fact, that the change of the size of caryopses happens during the micronization, the mathematical modeling, proved by experimental researches on the use of size of caryopses as a criterion for separating non-micronized grains, is relevant. AIM: Detecting the dominated variations in sizes of caryopses in cross-section at micronization. METHODS: In the analytical part of the research, the object was the mathematical models of caryopsis with relatively flat and incrassate shape. Modules of heat and strength analysis of the ANSYS software package were applied for modeling the thermal extension of a caryopsis by heating the surface with infrared radiation. In the experimental part of the research, the heating of caryopses was conducted with an infrared QHL radiation source with nominal rating power of 1500 W, the heating intervals of 10 seconds, the heating continued up to beginning of caryopsis darkening. The change in size before and after heating was measured with the ShCCB-1-150 0.01 beam-compass and the ICh-05 0.01 clock-type deteching head, the surface temperature of caryopses was measured using the Тesto 872 thermovisor and the IrSoft software. RESULTS: As the result of mathematical modeling of caryopsis extension by heating it was found that the change in thickness would be prevalent for flat caryopses, and the change in width would be prevalent for bulged caryopses. The experimental studies conducted on barley and wheat caryopses confirmed the modeling results: the increase in thickness prevailed in the flatter barley caryopses, whereas the increase in width prevailed in the more convex wheat caryopses. CONCLUSION: After micronization, flatter caryopses, such as barley caryopses, should be sorted on slotted screens according to thickness, whereas more convex caryopses, such as wheat caryopses, should be sorted on screens with circular holes according to width.
- 9 August 2026
- Published by ECO-Vector LLC (Publications) in Tractors and Agricultural Machinery
- Vol. 93 (3) , 289-300
Experimental-mathematical justification of criterion of grain micronization
BACKGROUND: During the micronization process, grain separation is necessary for those, the heating-up of which was insufficient. Considering the fact, that the change of the size of caryopses happens during the micronization, the mathematical modeling, proved by experimental researches on the use of size of caryopses as a criterion for separating non-micronized grains, is relevant. AIM: Detecting the dominated variations in sizes of caryopses in cross-section at micronization. METHODS: In the analytical part of the research, the object was the mathematical models of caryopsis with relatively flat and incrassate shape. Modules of heat and strength analysis of the ANSYS software package were applied for modeling the thermal extension of a caryopsis by heating the surface with infrared radiation. In the experimental part of the research, the heating of caryopses was conducted with an infrared QHL radiation source with nominal rating power of 1500 W, the heating intervals of 10 seconds, the heating continued up to beginning of caryopsis darkening. The change in size before and after heating was measured with the ShCCB-1-150 0.01 beam-compass and the ICh-05 0.01 clock-type deteching head, the surface temperature of caryopses was measured using the Тesto 872 thermovisor and the IrSoft software. RESULTS: As the result of mathematical modeling of caryopsis extension by heating it was found that the change in thickness would be prevalent for flat caryopses, and the change in width would be prevalent for bulged caryopses. The experimental studies conducted on barley and wheat caryopses confirmed the modeling results: the increase in thickness prevailed in the flatter barley caryopses, whereas the increase in width prevailed in the more convex wheat caryopses. CONCLUSION: After micronization, flatter caryopses, such as barley caryopses, should be sorted on slotted screens according to thickness, whereas more convex caryopses, such as wheat caryopses, should be sorted on screens with circular holes according to width.
- Open Access
- 25 March 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (1) , 60-83
The Effect of Air Pressure on the Technological Process of Grinding in the Grain Hammer Mill
Introduction. The main problem of the grain hammer mill is over-grinding of grain caused by untimely removal of the final product from the grinding chamber. A way to effect the air flow arrangement in the grain hammer mill is to change the air pressure around the grinding chamber. Therefore, the study of the effect of air pressure around the grain hammer mill on the quality and energy indicators of its operation is an urgent task today.Aim of the Study. The study is aimed at determining the effect of air pressure around the grinding chamber on the air flow motion pattern in the grain hammer mill and its energy indicators.Materials and Methods. For a theoretical study of the air flow circulation in the grinding chamber, there was constructed a geometric model of the rotor placed in the grinding chamber. The Reynolds averaged equations of a continuous medium motion was the basis for the mathematical model of air motion. The calculation results were used to construct the velocity fields for the air flow. To conduct experimental studies, there was designed a pressure chamber that allows changing the air pressure in the grain hammer mill.Results. Based on the results of theoretical studies, it has been determined that the pressure decrease in the grinding chamber by 10 times reduces the power consumption by 112 watts. Experimental studies have shown that when the pressure in the grinding chamber decreases, the power consumed by the engine for all types of rotors decreases too. Also, an increase in air pressure in the grinding chamber leads to a change in the amount of grinded grain remains on the sieve to 0 mm: for the blade and hammer rotors, the amount of remains decreases, and for the hammer-blade rotor it increases.Discussion and Conclusions. The results of theoretical and experimental studies have shown that decreasing the air pressure around the grinding chamber can decrease the energy costs for the technological process and air flow motion inside the grinding chamber, and reduce the over-grinding of grain. The study results make it possible to design the grinding chambers for grain hammer mills taking into account the air flow motion.
- 25 March 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (1) , 60-83
Open AccessThe Effect of Air Pressure on the Technological Process of Grinding in the Grain Hammer Mill
Introduction. The main problem of the grain hammer mill is over-grinding of grain caused by untimely removal of the final product from the grinding chamber. A way to effect the air flow arrangement in the grain hammer mill is to change the air pressure around the grinding chamber. Therefore, the study of the effect of air pressure around the grain hammer mill on the quality and energy indicators of its operation is an urgent task today.Aim of the Study. The study is aimed at determining the effect of air pressure around the grinding chamber on the air flow motion pattern in the grain hammer mill and its energy indicators.Materials and Methods. For a theoretical study of the air flow circulation in the grinding chamber, there was constructed a geometric model of the rotor placed in the grinding chamber. The Reynolds averaged equations of a continuous medium motion was the basis for the mathematical model of air motion. The calculation results were used to construct the velocity fields for the air flow. To conduct experimental studies, there was designed a pressure chamber that allows changing the air pressure in the grain hammer mill.Results. Based on the results of theoretical studies, it has been determined that the pressure decrease in the grinding chamber by 10 times reduces the power consumption by 112 watts. Experimental studies have shown that when the pressure in the grinding chamber decreases, the power consumed by the engine for all types of rotors decreases too. Also, an increase in air pressure in the grinding chamber leads to a change in the amount of grinded grain remains on the sieve to 0 mm: for the blade and hammer rotors, the amount of remains decreases, and for the hammer-blade rotor it increases.Discussion and Conclusions. The results of theoretical and experimental studies have shown that decreasing the air pressure around the grinding chamber can decrease the energy costs for the technological process and air flow motion inside the grinding chamber, and reduce the over-grinding of grain. The study results make it possible to design the grinding chambers for grain hammer mills taking into account the air flow motion.
- 27 December 2023
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 90 (6) , 575-583
Study of water heating efficiency in cavitation mode at the initial stage of grain molasses preparation
BACKGROUND: Grain molasses is a valuable source of digestible protein and feed sugar for farm animals. At the initial stage of production of this feed mixture, the existing devices and water heating schemes are not effective enough. Therefore, a new passive-type device for accelerated heating of water has been developed. AIM: Evaluation of efficiency of a cavitator for heating water at the grain molasses production plant. METHODS: In order to conduct studies, a cavitator made in the form of a cone with vanes, the apex angle of which is 16°8ʹ, is installed in a glass pipe of the injection branch of the water circuit of the plant for the preparation of grain molasses. During the experiments, the vanes were installed in the pipe straight or bent by 15°. In laboratory conditions, a comparative experiment was carried out to heat water with a volume of 50 liters, starting from its temperature of 20°C and through each degree to 30°C, both with and without the cavitator. The process efficiency criteria were: time and specific energy consumption of water heating. RESULTS: As a result of the conducted studies, the values of the efficiency criteria for the water heating process with and without the cavitator are found. Linear dependence of water temperature on heating time is obtained. It has been shown that the created cavitation effect behind the base of the cone is not stable, but still more intense behind the cone with straight petals. It is noted that the coefficient of hydraulic resistance for the cavitator with vanes bent by 15 ° is 10% greater than with straight ones. CONCLUSIONS: Use of a cavitator when heating water at the initial stage of preparing grain molasses increases efficiency of the process by 20%.
- 27 December 2023
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 90 (6) , 575-583
Study of water heating efficiency in cavitation mode at the initial stage of grain molasses preparation
BACKGROUND: Grain molasses is a valuable source of digestible protein and feed sugar for farm animals. At the initial stage of production of this feed mixture, the existing devices and water heating schemes are not effective enough. Therefore, a new passive-type device for accelerated heating of water has been developed. AIM: Evaluation of efficiency of a cavitator for heating water at the grain molasses production plant. METHODS: In order to conduct studies, a cavitator made in the form of a cone with vanes, the apex angle of which is 16°8ʹ, is installed in a glass pipe of the injection branch of the water circuit of the plant for the preparation of grain molasses. During the experiments, the vanes were installed in the pipe straight or bent by 15°. In laboratory conditions, a comparative experiment was carried out to heat water with a volume of 50 liters, starting from its temperature of 20°C and through each degree to 30°C, both with and without the cavitator. The process efficiency criteria were: time and specific energy consumption of water heating. RESULTS: As a result of the conducted studies, the values of the efficiency criteria for the water heating process with and without the cavitator are found. Linear dependence of water temperature on heating time is obtained. It has been shown that the created cavitation effect behind the base of the cone is not stable, but still more intense behind the cone with straight petals. It is noted that the coefficient of hydraulic resistance for the cavitator with vanes bent by 15 ° is 10% greater than with straight ones. CONCLUSIONS: Use of a cavitator when heating water at the initial stage of preparing grain molasses increases efficiency of the process by 20%.
- Open Access
- 31 March 2023
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 33 (1) , 37-51
Substantiation of the Structural and Technological Parameters of the Working Body of the Milling Grain Shredder
One of the main components in the diet of farm animals is concentrated feed, which in Russia is grinded by shredders. At the same time, in the final product, there is a high dust content, which can be reduced by using grinders with a different principle of grinding. The design of a milling shredder, in which grains are crushed by cutting, is proposed
- 31 March 2023
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 33 (1) , 37-51
Open AccessSubstantiation of the Structural and Technological Parameters of the Working Body of the Milling Grain Shredder
One of the main components in the diet of farm animals is concentrated feed, which in Russia is grinded by shredders. At the same time, in the final product, there is a high dust content, which can be reduced by using grinders with a different principle of grinding. The design of a milling shredder, in which grains are crushed by cutting, is proposed
- Open Access
- 28 February 2023
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 371, 03073
A research review on coarse grain micronization
This article gives an overview of research on grain micronization and the principal research areas that have been carried out in this respect. The results of the effects of infrared radiation on fodder grain used in animal feeding are presented. It is stated in most of the researches that micronization causes destruction of grain molecular structure, decreasing its hardness, partially changing amount of starch, which positively influences on absorption of grain treated by infra-red irradiation. The main lines of research into the micronization process are formulated.
- 28 February 2023
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 371, 03073
Open AccessA research review on coarse grain micronization
This article gives an overview of research on grain micronization and the principal research areas that have been carried out in this respect. The results of the effects of infrared radiation on fodder grain used in animal feeding are presented. It is stated in most of the researches that micronization causes destruction of grain molecular structure, decreasing its hardness, partially changing amount of starch, which positively influences on absorption of grain treated by infra-red irradiation. The main lines of research into the micronization process are formulated.
- 1 January 2018
- Published by O-Kratkoe Ltd in Theoretical and Applied Ecology
- No. 4,p. 24-29
Combined calculation schemes in mathematical models the fractionation of grain
Сельскохозяйственная экология предлагает новые методы и подходы к осуществлению производственных процессов, которые позволят снизить вредное влияние на окружающую среду. В статье изложены подходы к формированию комбинированной расчётной схемы процесса фракционирования зерновых материалов воздушным потоком в горизонтальном канале. Основной идеей метода является последовательное уточнение взаимного влияния зернового и воздушного потоков при расчёте поля скоростей воздуха и траекторий дисперсных частиц. Математическая модель движения воздушного потока построена на основе решения методом конечных элементов уравнений Лапласа для плоского потенциального течения с переменной скважностью. Дифференциальные уравнения движения дисперсных частиц решались численно, с применением метода усреднённого ускорения, с итерациями на каждом шаге и учётом распределения в канале поля скоростей воздушного потока. Комбинированная расчётная схема выполняется из нескольких итераций с поэтапным приближением к моделируемому процессу пневмосепарации. На первом этапе конечно-элементная модель течения воздушного потока строится без учёта влияния потока зернового материала. На втором этапе решаются дифференциальные уравнения движения частиц зернового материала. По решениям этих уравнений определяется зона большей или меньшей пористости. На следующем этапе проводится перерасчёт скоростей воздушного потока в канале с учётом пористости различных конечных элементов. В зависимости от скоростей воздушного потока изменяется результат решения дифференциальных уравнений движения дисперсных частиц. Таким образом происходит последовательное приближение к описанию процесса взаимодействия зернового и воздушного потоков. По предложенному алгоритму на языке C# разработана программа, предоставляющая возможность графического и числового контроля результатов расчёта. Интерфейс программы содержит три экранные формы с табличными исходными данными и схемой расположения конечных элементов, на которую, после вычислений, наносятся вектора скоростей воздушного потока и траектории частиц с заданными аэродинамическими свойствами. Представлены примеры расчёта. По их результатам предложено изменение величины и распределение скоростей воздушного потока на входе в канал, определены положения приёмников фракций в нижней части горизонтального пневмосепарирующего...
- 1 January 2018
- Published by O-Kratkoe Ltd in Theoretical and Applied Ecology
- No. 4,p. 24-29
Combined calculation schemes in mathematical models the fractionation of grain
Сельскохозяйственная экология предлагает новые методы и подходы к осуществлению производственных процессов, которые позволят снизить вредное влияние на окружающую среду. В статье изложены подходы к формированию комбинированной расчётной схемы процесса фракционирования зерновых материалов воздушным потоком в горизонтальном канале. Основной идеей метода является последовательное уточнение взаимного влияния зернового и воздушного потоков при расчёте поля скоростей воздуха и траекторий дисперсных частиц. Математическая модель движения воздушного потока построена на основе решения методом конечных элементов уравнений Лапласа для плоского потенциального течения с переменной скважностью. Дифференциальные уравнения движения дисперсных частиц решались численно, с применением метода усреднённого ускорения, с итерациями на каждом шаге и учётом распределения в канале поля скоростей воздушного потока. Комбинированная расчётная схема выполняется из нескольких итераций с поэтапным приближением к моделируемому процессу пневмосепарации. На первом этапе конечно-элементная модель течения воздушного потока строится без учёта влияния потока зернового материала. На втором этапе решаются дифференциальные уравнения движения частиц зернового материала. По решениям этих уравнений определяется зона большей или меньшей пористости. На следующем этапе проводится перерасчёт скоростей воздушного потока в канале с учётом пористости различных конечных элементов. В зависимости от скоростей воздушного потока изменяется результат решения дифференциальных уравнений движения дисперсных частиц. Таким образом происходит последовательное приближение к описанию процесса взаимодействия зернового и воздушного потоков. По предложенному алгоритму на языке C# разработана программа, предоставляющая возможность графического и числового контроля результатов расчёта. Интерфейс программы содержит три экранные формы с табличными исходными данными и схемой расположения конечных элементов, на которую, после вычислений, наносятся вектора скоростей воздушного потока и траектории частиц с заданными аэродинамическими свойствами. Представлены примеры расчёта. По их результатам предложено изменение величины и распределение скоростей воздушного потока на входе в канал, определены положения приёмников фракций в нижней части горизонтального пневмосепарирующего...