Hisao Miyazaki
Research Subjects
Hisao Miyazaki has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Shigeya Kimura
Corporate Research and Development Center Toshiba Corporation 1 Komukai-toshiba-cho, Saiwai-ku Kawasaki Kanagawa 212-8584 Japan
5 shared publications - Akihisa Ogino
Shizuoka University
4 shared publications - Kazuhito Tsukagoshi
Research Center for Materials Nanoarchitectonics (MANA), National Institute for Materials Science (NIMS), Namiki 1-1, Tsukuba 305-0044, Japan
2 shared publications Akihiro Kajita
Toshiba Corporation
1 shared publicationAkinobu Kanda
Institute of Physics and TIMS, University of Tsukuba, Tsukuba, Ibaraki 305-8571, Japan
1 shared publication- Hisashi Yoshida
Toshiba Co Ltd, Res & Dev Ctr, Kawasaki, Kanagawa 2128582, Japan
1 shared publication
Latest Publications
- Open Access
- 20 August 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (16) , 160903
Demonstration of a compact, self-contained, glass-encapsulated thermionic energy converter with an n-type AlGaN cathode
This study demonstrates a compact, self-contained, glass-encapsulated prototype thermionic energy converter (TEC) operating at around 300 °C, a remarkably low temperature for thermionic power generation. The device employs an n-type AlGaN thermionic cathode and is hermetically sealed in a glass-sealed Kovar package with a 3 cm‐diameter base. It consists of an AlGaN cathode, a perforated SUS anode, and a vacuum gap defined by insulating beads, together with an internal Cs accumulation region. Upon heating to 302 °C, the TEC produced an open-circuit voltage of 0.33 V and a short-circuit current density of 1.3 μA cm −2 .
- 20 August 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (16) , 160903
Open AccessDemonstration of a compact, self-contained, glass-encapsulated thermionic energy converter with an n-type AlGaN cathode
This study demonstrates a compact, self-contained, glass-encapsulated prototype thermionic energy converter (TEC) operating at around 300 °C, a remarkably low temperature for thermionic power generation. The device employs an n-type AlGaN thermionic cathode and is hermetically sealed in a glass-sealed Kovar package with a 3 cm‐diameter base. It consists of an AlGaN cathode, a perforated SUS anode, and a vacuum gap defined by insulating beads, together with an internal Cs accumulation region. Upon heating to 302 °C, the TEC produced an open-circuit voltage of 0.33 V and a short-circuit current density of 1.3 μA cm −2 .
- 15 January 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (3) , 03SP02
Photon-enhanced thermionic emission characteristics of Cs deposited Mg-doped InGaN
The effect of Mg doping on photon-enhanced thermionic emission (PETE) of InGaN emitters was investigated to reduce the high operating temperatures of thermionic energy converters (TECs). Mg-doped In0.15Ga0.85N enabled TEC operation at 100 °C and enhanced power generation at lower temperatures (100-400°C). In contrast, In0.15Ga0.85N without Mg doping required temperatures above 300 °C. Notably, the output power of TEC using Mg-doped In0.15Ga0.85N was approximately 8.6 times higher at 400 °C than that of InGaN emitter without Mg doping. This enhancement is attributed to Mg doping, which reduces the energy barrier for electron emission and increase the quasi-Fermi level under light irradiation. However, the performance of Mg-doped InGaN decreased at temperatures exceeding 400 °C, due to the limited availability of thermally excited electrons in p-type semiconductors and the increased work function resulting from Cs desorption. Overall, Mg-doped InGaN demonstrates strong potential as a PETE emitter for low-temperature operation and visible-light-driven applications.
- 15 January 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (3) , 03SP02
Photon-enhanced thermionic emission characteristics of Cs deposited Mg-doped InGaN
The effect of Mg doping on photon-enhanced thermionic emission (PETE) of InGaN emitters was investigated to reduce the high operating temperatures of thermionic energy converters (TECs). Mg-doped In0.15Ga0.85N enabled TEC operation at 100 °C and enhanced power generation at lower temperatures (100-400°C). In contrast, In0.15Ga0.85N without Mg doping required temperatures above 300 °C. Notably, the output power of TEC using Mg-doped In0.15Ga0.85N was approximately 8.6 times higher at 400 °C than that of InGaN emitter without Mg doping. This enhancement is attributed to Mg doping, which reduces the energy barrier for electron emission and increase the quasi-Fermi level under light irradiation. However, the performance of Mg-doped InGaN decreased at temperatures exceeding 400 °C, due to the limited availability of thermally excited electrons in p-type semiconductors and the increased work function resulting from Cs desorption. Overall, Mg-doped InGaN demonstrates strong potential as a PETE emitter for low-temperature operation and visible-light-driven applications.
- 1 May 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (5) , 051002
Surface activation of n-type AlGaN with cesium and oxygen to enhance thermionic emission
The aim of this study is to enhance the characteristics of thermionic emission of AlGaN surface through surface control employing cesium (Cs) and oxygen. Cs-deposited AlGaN has significant applications in thermionic energy converters. However, as the emitter temperature increases, the thermal desorption of Cs from AlGaN surface increases, resulting in a decrease in the thermionic emission current. Therefore, focusing on the high affinity between Cs and oxygen, we investigated the possibility of suppressing thermal desorption by depositing Cs and oxygen on AlGaN surface. The thermionic emission current measured when Cs and oxygen were alternately deposited on AlGaN surface was 1.9 × 10−3 A cm−2 at 500 °C. The thermionic emission current was significantly higher than that obtained with Cs-only deposition (2.0 × 10−5 A cm−2). In addition, we attempted to reproduce the effect of dynamic surface changes on thermionic emission employing a new thermionic emission model (modified Richardson–Dushman model) that considers the correlation between a specific surface reconstruction phase and its thermionic emission component. The results suggest that the adsorbed component of Cs-deposited AlGaN exhibits three Cs adsorption sites with different desorption energies, while the adsorbed component of Cs/O2 co-deposited AlGaN exhibits at least four Cs adsorption sites with different desorption energies. It is suggested that the increase in adsorption components with higher desorption energies, caused by the deposition of oxygen, may have reduced the thermal desorption and improved Cs coverage and stability.
- 1 May 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (5) , 051002
Surface activation of n-type AlGaN with cesium and oxygen to enhance thermionic emission
The aim of this study is to enhance the characteristics of thermionic emission of AlGaN surface through surface control employing cesium (Cs) and oxygen. Cs-deposited AlGaN has significant applications in thermionic energy converters. However, as the emitter temperature increases, the thermal desorption of Cs from AlGaN surface increases, resulting in a decrease in the thermionic emission current. Therefore, focusing on the high affinity between Cs and oxygen, we investigated the possibility of suppressing thermal desorption by depositing Cs and oxygen on AlGaN surface. The thermionic emission current measured when Cs and oxygen were alternately deposited on AlGaN surface was 1.9 × 10−3 A cm−2 at 500 °C. The thermionic emission current was significantly higher than that obtained with Cs-only deposition (2.0 × 10−5 A cm−2). In addition, we attempted to reproduce the effect of dynamic surface changes on thermionic emission employing a new thermionic emission model (modified Richardson–Dushman model) that considers the correlation between a specific surface reconstruction phase and its thermionic emission component. The results suggest that the adsorbed component of Cs-deposited AlGaN exhibits three Cs adsorption sites with different desorption energies, while the adsorbed component of Cs/O2 co-deposited AlGaN exhibits at least four Cs adsorption sites with different desorption energies. It is suggested that the increase in adsorption components with higher desorption energies, caused by the deposition of oxygen, may have reduced the thermal desorption and improved Cs coverage and stability.
- 27 May 2022
- Published by IOP Publishing in Applied Physics Express
- Vol. 15 (6) , 061006
Diamond hollow cathode with axial magnetic field for high-density cold plasma source
We present a high-density plasma source using a hollow cathode with an axial magnetic field. The hollow cathode consists of molybdenum plates coated by polycrystalline boron-doped diamond (PBDD) with a high yield of ion-induced secondary electrons. Impact ionization was promoted by gyromotion in the hollow cathode with a magnetic field. A normalized current density four orders of magnitude larger than that of a planar cathode without a magnetic field was obtained. The high-quality PBDD cathode enables lower discharge sustain voltage and higher current density without glow-to-arc transition compared with low-quality PBDD and other cathode materials.
- 27 May 2022
- Published by IOP Publishing in Applied Physics Express
- Vol. 15 (6) , 061006
Diamond hollow cathode with axial magnetic field for high-density cold plasma source
We present a high-density plasma source using a hollow cathode with an axial magnetic field. The hollow cathode consists of molybdenum plates coated by polycrystalline boron-doped diamond (PBDD) with a high yield of ion-induced secondary electrons. Impact ionization was promoted by gyromotion in the hollow cathode with a magnetic field. A normalized current density four orders of magnitude larger than that of a planar cathode without a magnetic field was obtained. The high-quality PBDD cathode enables lower discharge sustain voltage and higher current density without glow-to-arc transition compared with low-quality PBDD and other cathode materials.
- 5 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Enhancement of thermionic emission and conversion characteristics using polarization- and band-engineered n-type AlGaN cathodes
We observed enhancement of thermionic emission (TE) and conversion (TC) characteristics by controlling spontaneous and piezo polarization and the band diagram of n-type AlGaN/GaN thermionic cathodes. The obtained TE current from N-polarity n-AlGaN films grown on an n-GaN substrate was 0.29 mA at 500 °C in a Cs gas atmosphere in the vacuum gap between the cathode and a stainless steel anode. This TE current was 5.0 times and 1.6 times higher than that from the surface of Ga-polarity n-GaN substrate and that of the Ga-polarity n-AlGaN film on the substrate, respectively.
- 5 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Enhancement of thermionic emission and conversion characteristics using polarization- and band-engineered n-type AlGaN cathodes
We observed enhancement of thermionic emission (TE) and conversion (TC) characteristics by controlling spontaneous and piezo polarization and the band diagram of n-type AlGaN/GaN thermionic cathodes. The obtained TE current from N-polarity n-AlGaN films grown on an n-GaN substrate was 0.29 mA at 500 °C in a Cs gas atmosphere in the vacuum gap between the cathode and a stainless steel anode. This TE current was 5.0 times and 1.6 times higher than that from the surface of Ga-polarity n-GaN substrate and that of the Ga-polarity n-AlGaN film on the substrate, respectively.
- 27 January 2017
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 56 (4S) , 04CP02
MoCl 5 intercalation doping and oxygen passivation of submicrometer-sized multilayer graphene
We investigated doping material selection for multilayer graphene (MLG) interconnects and a passivation process to stabilize the doped state. Intercalation doping with Br 2 , FeCl 3 , and MoCl 5 was compared in terms of doping ability and robustness against environmental effects, which are exacerbated by miniaturization. We found that MoCl 5 was advantageous for miniaturization. We hypothesized that environmental stability would be enhanced by partially oxidizing MoCl 5 and avoiding hydrolysis by water vapor in air. To test this, we examined a passivation process by dry oxygen exposure. We verified that the doping effect was improved and that intercalated material (MoCl 5 ) was partially oxidized and confined in the MLG.
- 27 January 2017
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 56 (4S) , 04CP02
MoCl 5 intercalation doping and oxygen passivation of submicrometer-sized multilayer graphene
We investigated doping material selection for multilayer graphene (MLG) interconnects and a passivation process to stabilize the doped state. Intercalation doping with Br 2 , FeCl 3 , and MoCl 5 was compared in terms of doping ability and robustness against environmental effects, which are exacerbated by miniaturization. We found that MoCl 5 was advantageous for miniaturization. We hypothesized that environmental stability would be enhanced by partially oxidizing MoCl 5 and avoiding hydrolysis by water vapor in air. To test this, we examined a passivation process by dry oxygen exposure. We verified that the doping effect was improved and that intercalated material (MoCl 5 ) was partially oxidized and confined in the MLG.
- Open Access
- 16 April 2012
- Published by AIP Publishing in Applied Physics Letters
- Vol. 100 (16) , 163115
Unipolar transport in bilayer graphene controlled by multiple p-n interfaces
Unipolar transport is demonstrated in a bilayer graphene with a series of p-n junctions and is controlled by electrostatic biasing by a comb-shaped top gate. The OFF state is induced by multiple barriers in the p-n junctions, where the band gap is generated by applying a perpendicular electric field to the bilayer graphene, and the ON state is induced by the p-p or n-n configurations of the junctions. As the number of the junction increases, current suppression in the OFF state is pronounced. The multiple p-n junctions also realize the saturation of the drain current under relatively high source-drain voltages.
- 16 April 2012
- Published by AIP Publishing in Applied Physics Letters
- Vol. 100 (16) , 163115
Open AccessUnipolar transport in bilayer graphene controlled by multiple p-n interfaces
Unipolar transport is demonstrated in a bilayer graphene with a series of p-n junctions and is controlled by electrostatic biasing by a comb-shaped top gate. The OFF state is induced by multiple barriers in the p-n junctions, where the band gap is generated by applying a perpendicular electric field to the bilayer graphene, and the ON state is induced by the p-p or n-n configurations of the junctions. As the number of the junction increases, current suppression in the OFF state is pronounced. The multiple p-n junctions also realize the saturation of the drain current under relatively high source-drain voltages.
- 1 January 2008
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 47 (1S) , 697-699
Coulomb Blockade Oscillations in Patterned Ultrathin Graphite Films
- 1 January 2008
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 47 (1S) , 697-699
Coulomb Blockade Oscillations in Patterned Ultrathin Graphite Films
- 1 June 1995
- Published by Elsevier in Journal of Molecular Spectroscopy
- Vol. 171 (2) , 565-568
Microwave Spectrum and Quadrupole Coupling Constants of s-trans-Acryloyl Chloride
- 1 June 1995
- Published by Elsevier in Journal of Molecular Spectroscopy
- Vol. 171 (2) , 565-568
Microwave Spectrum and Quadrupole Coupling Constants of s-trans-Acryloyl Chloride