Prapan Leekul
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Prapan Leekul has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Hoang Nam Dao
High-Tech Telecommunication Center, Hanoi, Vietnam
2 shared publications - Monai Krairiksh
School of Engineering, King Mongkuts Institute of Technology Ladkrabang, Bangkok, Thailand
2 shared publications - Thunyawat Limpiti
Walailak University
2 shared publications Bonny Mgawe
St. Augustine University, Mwanza, Tanzania
1 shared publication- Charernkiat Pochaiya
Department of Electrical Engineering, School of Engineering and Technology, Walailak University, Nakhon Si Thammarat 80161, Thailand
1 shared publication - Chuwong Phongcharoenpanich
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand
1 shared publication
Latest Publications
- Open Access
Implementing a Low-Cost Non-Destructive Microwave Sensor to Monitor the Real-Time Moisture Content of Rubber Wood in Industrial Dehydration Processes
This study aims to present a low-cost, non-destructive microwave sensor implementation to monitor the real-time moisture content of rubber wood in industrial dehydration processes. The proposed sensor is based on the free-space measurement technique with magnitudes S11 and S21 only. The novelties of this study consist of the natural frequency determination of rubber wood and the design of a sensor system using devices available on the market with reasonable cost performance. The natural frequency was determined using a simulation and was equal to 1.25 GHz. It specified the sensor system design and device selection. The designed system was initially verified by measuring the moisture content of rubber wood in the laboratory. The measured S11 and S21 voltages correlating with moisture content percentages were obtained and programmed. The system was then installed to monitor the moisture content of rubber wood in the dehydration process. The measured results deviated from those obtained from a standard method in the range of 7.67–15.38%. The error compensation was analyzed to improve the measured results that provided the deviated moisture content in the range of 3.58–5.21%. It can be inferred that the proposed sensor system has the capability to be implemented in industrial dehydration processes.
Open AccessImplementing a Low-Cost Non-Destructive Microwave Sensor to Monitor the Real-Time Moisture Content of Rubber Wood in Industrial Dehydration Processes
This study aims to present a low-cost, non-destructive microwave sensor implementation to monitor the real-time moisture content of rubber wood in industrial dehydration processes. The proposed sensor is based on the free-space measurement technique with magnitudes S11 and S21 only. The novelties of this study consist of the natural frequency determination of rubber wood and the design of a sensor system using devices available on the market with reasonable cost performance. The natural frequency was determined using a simulation and was equal to 1.25 GHz. It specified the sensor system design and device selection. The designed system was initially verified by measuring the moisture content of rubber wood in the laboratory. The measured S11 and S21 voltages correlating with moisture content percentages were obtained and programmed. The system was then installed to monitor the moisture content of rubber wood in the dehydration process. The measured results deviated from those obtained from a standard method in the range of 7.67–15.38%. The error compensation was analyzed to improve the measured results that provided the deviated moisture content in the range of 3.58–5.21%. It can be inferred that the proposed sensor system has the capability to be implemented in industrial dehydration processes.
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (12) , 21535-21545
Single-Frequency Sensor for Thick Rind Fruit Quality Assessment
A sensor capable of estimating the dielectric properties of the outer and inner materials of a concentric dielectric sphere is essential for assessing the quality of thick rind fruits. This paper presents a sensor design that operates at a single frequency and is straightforward. The underlying principle of the sensor involves transmitting a microwave signal to a concentric dielectric sphere with two power levels. The low-power signal yields backscattered wave from the outer sphere, while the high-power signal provides information about backscattered wave from both the outer and inner spheres. The sensor, which operates at a frequency of 10 GHz using cost-effective components, effectively detects defects in spherical-shape fruits, e.g. mangosteens. The accuracy in classifying translucent mangosteens from normal mangosteens is 92.5 % enables effective classification of defected fruits.
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (12) , 21535-21545
Single-Frequency Sensor for Thick Rind Fruit Quality Assessment
A sensor capable of estimating the dielectric properties of the outer and inner materials of a concentric dielectric sphere is essential for assessing the quality of thick rind fruits. This paper presents a sensor design that operates at a single frequency and is straightforward. The underlying principle of the sensor involves transmitting a microwave signal to a concentric dielectric sphere with two power levels. The low-power signal yields backscattered wave from the outer sphere, while the high-power signal provides information about backscattered wave from both the outer and inner spheres. The sensor, which operates at a frequency of 10 GHz using cost-effective components, effectively detects defects in spherical-shape fruits, e.g. mangosteens. The accuracy in classifying translucent mangosteens from normal mangosteens is 92.5 % enables effective classification of defected fruits.
- Open Access
- 1 February 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (1) , 549-560
An intelligent humidity control system for mushroom growing house by using beam-switching antennas with artificial neural networks
An automatic humidity control system for mushroom growing house based on the free-space technique is presented. The novelty of this work is the modified free-space technique by measuring the amplitude only of transmission coefficient |S21| that reflected from mushroom by using beam-switching antenna with artificial neural networks (ANNs) as a humidity sensor to control quantity and time of water misting nozzle. In the proposed system, the antenna is designed to act as the transmitting antenna at the frequency of 2.45 GHz. Its radiation patterns can be switched to 4 directions covering all corners of mushroom growing house. The measured |S21| from each direction are converted to direct current (DC) voltage by a radio frequency (RF) detector; then are trained with ANNs in the humidity range of 60-85%. The optimized ANNs structure consists of 4 input nodes, two layers of 5 hidden nodes, and 3 output nodes. To verify the proposed system, experiments were set up in controlled humidity mushroom growing house at the humidity level of 75-80% for 120 hours. The results showed that there was slightly average standard deviation (S.D.) of humidity level 1.36. Consequently, the performance of sensor system assures that it is able to apply for humidity control in large growing house.
- 1 February 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (1) , 549-560
Open AccessAn intelligent humidity control system for mushroom growing house by using beam-switching antennas with artificial neural networks
An automatic humidity control system for mushroom growing house based on the free-space technique is presented. The novelty of this work is the modified free-space technique by measuring the amplitude only of transmission coefficient |S21| that reflected from mushroom by using beam-switching antenna with artificial neural networks (ANNs) as a humidity sensor to control quantity and time of water misting nozzle. In the proposed system, the antenna is designed to act as the transmitting antenna at the frequency of 2.45 GHz. Its radiation patterns can be switched to 4 directions covering all corners of mushroom growing house. The measured |S21| from each direction are converted to direct current (DC) voltage by a radio frequency (RF) detector; then are trained with ANNs in the humidity range of 60-85%. The optimized ANNs structure consists of 4 input nodes, two layers of 5 hidden nodes, and 3 output nodes. To verify the proposed system, experiments were set up in controlled humidity mushroom growing house at the humidity level of 75-80% for 120 hours. The results showed that there was slightly average standard deviation (S.D.) of humidity level 1.36. Consequently, the performance of sensor system assures that it is able to apply for humidity control in large growing house.
- Open Access
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 54516-54524
Simple and Effective Design Concept for Constructing In-Situ Soil Dielectric Property Sensor With Dual Low-Cost COTS Microwave Modules
This paper presents a compact sensor system for estimating the dielectric properties of materials based on commercial, off-the-shelf (COTS) modules. The dielectric constant and conductivity of a material under test can be determined from the measurement of the microwave reflected from the material. By using dual microwave sensor modules with a slightly different radio frequency, an identical intermediate frequency at the mixers of the modules was obtained. The intermediate frequency was chosen such that the associated microwave and data processing components could be easily obtainable, leading to a practical realization of the sensor system. Synchronization of the two microwave sensor modules was achieved using electronically controlled relays that simultaneously switch on the power supplies of both modules. Two microcontrollers were used to capture the corresponding signals. The sensor was designed at a 10 GHz band for measuring reflected waves from various kinds of materials, especially soils with different moisture and fertilizer contents. The evaluation results indicate a good agreement between the measured results from the proposed sensor and the ones from a network analyzer, verifying that the proposed sensor is fully functional for monitoring variation in the dielectric properties of materials, including soil. The average sensitivity for the dielectric constant of moist soil is 0.26/% moisture content and the error rate for dielectric constant measurement is 4.83%.
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 54516-54524
Open AccessSimple and Effective Design Concept for Constructing In-Situ Soil Dielectric Property Sensor With Dual Low-Cost COTS Microwave Modules
This paper presents a compact sensor system for estimating the dielectric properties of materials based on commercial, off-the-shelf (COTS) modules. The dielectric constant and conductivity of a material under test can be determined from the measurement of the microwave reflected from the material. By using dual microwave sensor modules with a slightly different radio frequency, an identical intermediate frequency at the mixers of the modules was obtained. The intermediate frequency was chosen such that the associated microwave and data processing components could be easily obtainable, leading to a practical realization of the sensor system. Synchronization of the two microwave sensor modules was achieved using electronically controlled relays that simultaneously switch on the power supplies of both modules. Two microcontrollers were used to capture the corresponding signals. The sensor was designed at a 10 GHz band for measuring reflected waves from various kinds of materials, especially soils with different moisture and fertilizer contents. The evaluation results indicate a good agreement between the measured results from the proposed sensor and the ones from a network analyzer, verifying that the proposed sensor is fully functional for monitoring variation in the dielectric properties of materials, including soil. The average sensitivity for the dielectric constant of moist soil is 0.26/% moisture content and the error rate for dielectric constant measurement is 4.83%.