BSBelete Sirhabizu

Belete Sirhabizu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Belete Sirhabizu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    RSM-based optimization of mechanical and moisture resistance properties of ternary polymer nanocomposites

    by Aynamaw Betsene Wero, Belete Sirahbizu Yigezu

    Epoxy-based polymer Nanocomposites are widely investigated for electrical insulation applications due to their exceptional mechanical and dielectric properties; however, moisture absorption and brittleness remain major challenges. This study aimed to develop and optimize Epoxy/ Ethylene Propylene Diene Monomer (EPDM) /nano-silica ternary nanocomposites with increased tensile strength and reduced water absorption using Response Surface Methodology (RSM) based on Central Composite Design (CCD). The effects of EPDM concentration, nano-silica loading, and sonication time were evaluated through 20 experimental runs. Water absorption was measured according to ASTM D570 after 240-hour immersion, while tensile strength was determined using ASTM D638 standard. The statistical analysis showed that all three processing parameters significantly affected the measured responses within the investigated experimental ranges, with nano-silica loading showing the largest statistical effect. The developed linear models showed satisfactory fit and predictive statistics, with non-significant lack-of-fit results. Increasing nano-silica loading and sonication time was associated with increased tensile strength and reduced water absorption within the experimental design space. These response trends may be related to changes in the polymer–filler environment and the processing-dependent state of the silica-containing phase. The optimized formulation exhibited a tensile strength of 90.9 ± 0.46 MPa and water absorption of 0.0441 ± 0.0003% under the investigated test conditions. Overall, the results demonstrate the potential of the Epoxy/EPDM/nano-silica system as a candidate for further investigation in electrical-insulation applications.

  • Open Access

    Multi-Objective Optimization of Carbonized False Banana Fiber/Fe3O4 Hybrid Composites for Lightweight Broadband Electromagnetic Absorption in UAV Applications

    by Michael A. Gebremichael, Belete S. Yigezu, Girma T. Chala

    Nowadays, carbonized natural fiber composites are sustainable alternatives for electromagnetic wave absorption in unmanned aerial vehicles (UAVs). However, achieving a balance between electromagnetic performance, structural thickness, and weight is still difficult. This study, therefore, presents a multi-objective optimization framework for designing a lightweight radar-absorbing multilayer composite using a carbonized false banana fiber/Fe3O4 hybrid absorber. In this work, a four-layer sandwich panel was modeled in SOLIDWORKS 2017 and analyzed using full-wave electromagnetic simulation in ANSYS HFSS (R18.1) over the frequency range of 2–18 GHz. Layer thicknesses were optimized using a multi-objective particle swarm optimization (MOPSO) algorithm with three objectives: maximizing the frequency-averaged power absorptivity, minimizing panel mass, and minimizing total thickness. The objectives were handled simultaneously through Pareto dominance without predefined weighting coefficients, and a compromise solution was selected from the resulting Pareto-optimal set. The selected Pareto compromise was subsequently adjusted considering practical layer-thickness and manufacturability requirements, resulting in a 2/5/2/1 mm multilayer configuration with a total thickness of 10 mm. The resulting configuration achieved frequency-averaged power absorptivities of 0.6756 over 2–18 GHz and 0.8289 within the Ku-band, together with an effective absorption bandwidth of 3.2 GHz for power absorptivity above 90%. A minimum reflection coefficient magnitude of 0.0230 (corresponding to a peak power absorptivity of 99.95% at resonance) was obtained, with a minimum reflection loss of −32.75 dB. The optimized panel achieved a mass of 0.1725 kg, corresponding to a modest 1.42% reduction relative to an equal-footprint, equal-thickness monolithic carbon-fiber reference panel. These numerical results show the potential of combining a biomass-derived absorber with multi-objective optimization for the preliminary design of UAV-oriented radar-absorbing multilayer structures.

  • Open Access

    Effect of NaOH Treatment and Solvent Extraction on the Chemical Composition and Morphology of False Banana ( Ensete ventricosum ) Fibers

    by Michael Ayele Gebremichael, Belete Sirahbizu Yigezu

    Natural fibers have attracted increasing attention as sustainable alternatives to synthetic reinforcements due to their biodegradability, renewability, and low environmental impact. False banana ( Ensete ventricosum ) fibers, however, contain significant amounts of noncellulosic components such as hemicellulose, lignin, and extractives, which can limit their interfacial performance in composite materials. This study investigates the effects of sodium hydroxide (NaOH) pretreatment at concentrations of 2%–8% combined with Soxhlet benzene–ethanol (2:1 v/v) extraction on the chemical composition and surface morphology of these fibers. Chemical analysis revealed that NaOH treatment substantially reduced extractives from 1.28% to 0.35% and hemicellulose from 16.21% to 9.44%, while lignin content decreased from 19.65% to 15.50%, indicating partial delignification. Thus, the calculated cellulose content increased from 62.87% in untreated fibers to 74.71% after 8% NaOH treatment, reflecting the progressive removal of noncellulosic components rather than an absolute increase in cellulose. Scanning electron microscopy revealed progressive surface cleaning, increased fibrillation, and enhanced surface roughness with increasing NaOH concentration. Fibers treated with 4%–6% NaOH exhibited the most favorable balance between chemical purification and structural integrity, whereas treatment with 8% NaOH resulted in surface microcracks and partial structural degradation due to excessive alkali attack. These findings reveal that the combined NaOH/Soxhlet pretreatment effectively improves both the chemical purity and surface morphology of E. ventricosum fibers, thereby improving their potential as sustainable reinforcement materials for biocomposite applications.

  • Open Access

    Experimental investigation on tensile strength and impact strength of palmyra palm leaf stalk – Sisal fiber reinforced polymer hybrid composite

    by Adugnaw Ayalew Bekele, Haymanot Takele Mekonnen, Belete Sirahbizu Yigezu, Abyot Yassab Nega


  • A study of the mechanical, thermal and rheological properties of sisal fiber-reinforced polylactic acid bio-composites with tributyl 2-acetylcitrate as a plasticizer

    by Eshetie Kassegn, Belete Sirhabizu, Temesgen Berhanu, Bart Buffel, Frederik Desplentere

    In this study, bio-composites were developed using polylactic acid (PLA) as the matrix and sisal fibers (SFs) derived from agave sisalana leaves as the reinforcement. The bio-composites were prepared through injection molding with the addition of tributyl 2-acetylcitrate (ATBC) plasticizer. The mechanical, thermal, and rheological properties of these bio-composites were investigated to understand the effects of fiber and plasticizer contents. The results showed that the addition of SFs improved the tensile and flexural moduli of the bio-composites but led to a decrease in tensile strength compared to neat PLA. The flexural strength initially decreased with low fiber content but recovered to the level of neat PLA as the fiber content increased. The impact strength increased with the incorporation of SFs and ATBC. However, the presence of ATBC had a negative impact on the tensile and flexural properties of the bio-composites. The thermal conductivity of the materials was influenced by the fiber content and processing temperature, increasing with SFs inclusion but decreasing with temperature. Differential scanning calorimetry analysis revealed increased crystallinity of PLA with the presence of SFs and ATBC. The specific heat capacity increased with ATBC but decreased with increasing SFs. Dynamic mechanical property testing showed variations in storage and loss moduli of the bio-composites at different temperatures. The storage modulus increased with higher fiber content and abruptly dropped around glass transition temperature. Rheological characterization demonstrated effective interactions between the fibers and matrix with good fiber dispersion, resulting in uniform shear viscosity versus shear rate for different capillary dimensions. The shear viscosity of the SFs/PLA mixture increased with increasing fiber content but decreased with the addition of plasticizer. Furthermore, the compounding and molding processes had a notable impact on the microstructure of the fibers, specifically resulting in fiber breakage and fiber separation during processing.


  • Open Access

    Influence of fiber surface treatment on the mechanical properties of sisal fiber reinforced polylactic acid bio-composites

    by Eshetie Kassegn, Belete Sirhabizu, Temesgen Berhanu, Bart Buffel, Frederik Desplentere

    Gaining an understanding of how chemical treatment affects the mechanical properties of natural fiber reinforced polymer composites is essential to enhance their performance and broaden their applicability across various engineering domains. The objective of this study was to develop bio-composites by combining polylactic acid with sisal fibers that have undergone chemical treatments and evaluating the mechanical properties at different temperatures to determine their suitability for high-temperature applications. For this purpose, sisal fibers were chemically treated using alkali, acetylation, and alkali/acetylation solution before composite processing. The results revealed that tensile strength slightly improved by alkali treatment, while both alkali/acetylation and acetylation treatments decreased the tensile strength and tensile modulus. Alkali treatment significantly enhanced flexural strength, while the effect of acetylation and alkali/acetylation treatments on flexural strength was less pronounced. All chemical treatments led to a slight increase in flexural strain at failure, but resulted in a decrease in tensile strain at failure and tensile modulus. Alkali treatment slightly increased flexural modulus, while acetylation and alkali/acetylation treatments significantly reduced it. The impact strength of the bio-composites was increased by alkali and acetylation treatments, but significantly reduced by alkali/acetylation treatment. Furthermore, the flexural strength of all bio-composites decreased as temperature increased, especially in plasticized bio-composites using tributyl 2-acetylcitrate plasticizer. The flexural strain at failure decreased with the addition of tributyl 2-acetylcitrate at room temperature. In plasticized bio-composites, the flexural strain at failure increased at 35°C, but decreased at 45°C. On the other hand, the flexural strain at failure of non-plasticized bio-composites remained constant up to 35°C, slightly increased up to 45°C, and then significantly increased at temperatures above 45°C. These bio-composites could be suitable for packaging industry as biodegradability is the criteria for such applications.


  • Open Access

    Moisture Absorption Characteristics and Subsequent Mechanical Property Loss of Enset–PLA Composites

    by Abebayehu Abdela, Maxim Vandaele, Sam Haenen, Bart Buffel, Belete Sirahbizu, Frederik Desplentere

    One of the drawbacks of natural fibers and their composites is their inherent hydrophilic nature. The effect of moisture on the mechanical properties of composites is irrefutable. This study deals with the hygroscopic characteristics of enset–PLA composites and their effect on the mechanical properties of the composites. To do this, injection-molded composite specimens with different fiber volume fractions, plasticizer ratios, fiber lengths, and fiber ages were considered. The specimens were exposed to distilled water, and the moisture absorption was monitored on a daily basis. Subsequently, the specimens were subjected to mechanical loading to determine the effect of moisture on their strength, stiffness, and strain at break strength. Lastly, the individual and joint effects of the considered factors were scrutinized using an optimal experimental design. The results of the study show that the maximum and minimum moisture uptakes were recorded for 25% and 15% fiber ratios, respectively. Due to the effect of moisture, the tensile and bending strength decreased by 11% and 5%, respectively, for the 15% fiber volume fraction and decreased by 16% and 13%, respectively, for the 25% fiber volume fraction. Increasing the amount of plasticizer increases the moisture resistance. The results indicate that Enset–PLA composites have competitive properties and stability when exposed to moisture.


  • Open Access

    Investigating the Dimensional, Mechanical, and Morphological Properties of Composites Reinforced with Sisal Fibers and Polylactic Acid in Response to Water Absorption

    by Eshetie Kassegn, Belete Sirhabizu, Temesgen Berhanu, Bart Buffel, Frederik Desplentere

    Biocomposites are promising candidates for some engineering applications owing to the growing environmental and economic challenges to replace petrochemical-based polymers with biodegradable polymers. Herein, sisal fiber reinforced polylactic acid (PLA) composite specimens were fabricated using an injection molding machine with and without plasticizer. The weight percentage (wt%) of the sisal fiber varied between 5% and 20%. The effect of the sisal fiber wt% on water absorption resistance and mechanical properties was investigated experimentally using water ageing, mechanical, and morphological studies. The results revealed that tensile and flexural specimens after water ageing exhibited lower tensile and flexural strengths with higher water absorption behavior at 20 wt% sisal fiber than 5 wt% sisal fiber, while the impact strength increased after water ageing. In addition, the sisal fiber/PLA composites exhibited higher water absorption behavior and lower strength and modulus at 20 wt% sisal fiber after water ageing. Moreover, the water absorption decreased with the incorporation of the plasticizer.