Yaqdhan Mahmood Hussein
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yaqdhan Mahmood Hussein has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Fahad Taha Al-Dhief
Universiti Kebangsaan Malaysia
3 shared publications - Hatem Oday Hanoosh
Advance RF and Microwave Research Group (ARFMRG), Faculty of Electrical Engineering, Universiti Teknologi Malaysia (UTM), Johor Bahru, Johor, Malaysia
3 shared publications - Tabarek Alwan Tuib
University of Tabriz
3 shared publications - Baydaai Hadi Saoudi
Al-Furat Al-Awsat Technical University
2 shared publications - Mohamad Kamal Abd Rahim
Department of Communication Engineering, Faculty of Electrical Engineering, Universiti Teknologi Malaysia, Johor Bahru, Malaysia
2 shared publications - Noor Asniza Murad
Advance RF and Microwave Research Group (ARFMRG), Faculty of Electrical Engineering, Universiti Teknologi Malaysia (UTM), Johor Bahru, Johor, Malaysia
2 shared publications
Latest Publications
- Open Access
- 1 August 2026
- Published by Institute of Advanced Engineering and Science in IAES International Journal of Artificial Intelligence (IJ-AI)
- Vol. 15 (4) , 3692-3702
Text emotion recognition based on deep learning and attention with whale optimization algorithm
Text emotion recognition (TER) represents one of the crucial tasks in natural language processing (NLP), and it is highly important for many applications. To improve the performance of TER, advanced deep learning (DL) model GRU-BiGRU-CNN-Att is presented in this research. It is a combination of gated recurrent units (GRU), bidirectional gated recurrent units (BiGRU) with a convolutional neural network (CNN), and an attention mechanism. Using a GRU, BiGRU, and CNN as part of a deep feature extraction model, combined with an attention mechanism that gives important information different weights, the method that is proposed in the present work enhances the quality of the word vectors and leads to increasing sentiment analysis judgment accuracy. The whale optimization algorithm (WOA), which selects the most informative features for further enhancing the model, is used lastly for the optimization of the feature selection process. After such optimization, those chosen features are trained on a multi-layer perceptron (MLP), successfully combining machine learning (ML) and DL approaches for improving TER. A varied corpus of tweets, sentences, and dialogues had been used in the present work for the assessment of the performance of the suggested model. The proposed method achieves 83.76% accuracy in emotion recognition.
- 1 August 2026
- Published by Institute of Advanced Engineering and Science in IAES International Journal of Artificial Intelligence (IJ-AI)
- Vol. 15 (4) , 3692-3702
Open AccessText emotion recognition based on deep learning and attention with whale optimization algorithm
Text emotion recognition (TER) represents one of the crucial tasks in natural language processing (NLP), and it is highly important for many applications. To improve the performance of TER, advanced deep learning (DL) model GRU-BiGRU-CNN-Att is presented in this research. It is a combination of gated recurrent units (GRU), bidirectional gated recurrent units (BiGRU) with a convolutional neural network (CNN), and an attention mechanism. Using a GRU, BiGRU, and CNN as part of a deep feature extraction model, combined with an attention mechanism that gives important information different weights, the method that is proposed in the present work enhances the quality of the word vectors and leads to increasing sentiment analysis judgment accuracy. The whale optimization algorithm (WOA), which selects the most informative features for further enhancing the model, is used lastly for the optimization of the feature selection process. After such optimization, those chosen features are trained on a multi-layer perceptron (MLP), successfully combining machine learning (ML) and DL approaches for improving TER. A varied corpus of tweets, sentences, and dialogues had been used in the present work for the assessment of the performance of the suggested model. The proposed method achieves 83.76% accuracy in emotion recognition.
- Open Access
- 1 December 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (4) , 2582-2591
Enhanced voltage stability in power distribution networks through optimal reconfiguration using hybrid metaheuristic algorithms
An optimal network reconfiguration (ONR) is used in distribution power systems to improve voltage decreases within the permitted period and minimize real power losses. Consequently, attaining optimal reconfiguration in distribution systems is regarded as the primary objective of numerous researchers. Conventional heuristic techniques such as genetic algorithms (GA), ant colony optimization (ACO), and particle swarm optimization (PSO) can reduce active power losses and enhance network stability. These algorithms indicate a greater number of difficulties, including inadequate convergence characteristics, a reduction in power loss, and an increase in bus voltage. This research proposes effective optimization strategies utilizing the salp swarm algorithm (SSA) and whale optimization algorithm (WOA) to augment bus voltage, reduce distribution losses, and improve network dependability. The proposed algorithms are executed and evaluated on the IEEE 33-bus and 69-bus networks to determine the ideal network architecture. The efficacy of the examined methodologies is illustrated through MATLAB under steady-state conditions, showcasing benefits in the reduction of active power loss relative to current algorithms. The comparison indicates that the SSA algorithm exhibits superior performance in terms of power losses and bus voltage enhancement relative to the WOA method. due to its enhanced exploration and exploitation capabilities, which help avoid local optima and ensure a more effective search for optimal solutions. SSA's adaptive mechanism and cooperative behavior improve convergence speed and solution accuracy, making it more efficient for optimization in network reconfiguration.
- 1 December 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (4) , 2582-2591
Open AccessEnhanced voltage stability in power distribution networks through optimal reconfiguration using hybrid metaheuristic algorithms
An optimal network reconfiguration (ONR) is used in distribution power systems to improve voltage decreases within the permitted period and minimize real power losses. Consequently, attaining optimal reconfiguration in distribution systems is regarded as the primary objective of numerous researchers. Conventional heuristic techniques such as genetic algorithms (GA), ant colony optimization (ACO), and particle swarm optimization (PSO) can reduce active power losses and enhance network stability. These algorithms indicate a greater number of difficulties, including inadequate convergence characteristics, a reduction in power loss, and an increase in bus voltage. This research proposes effective optimization strategies utilizing the salp swarm algorithm (SSA) and whale optimization algorithm (WOA) to augment bus voltage, reduce distribution losses, and improve network dependability. The proposed algorithms are executed and evaluated on the IEEE 33-bus and 69-bus networks to determine the ideal network architecture. The efficacy of the examined methodologies is illustrated through MATLAB under steady-state conditions, showcasing benefits in the reduction of active power loss relative to current algorithms. The comparison indicates that the SSA algorithm exhibits superior performance in terms of power losses and bus voltage enhancement relative to the WOA method. due to its enhanced exploration and exploitation capabilities, which help avoid local optima and ensure a more effective search for optimal solutions. SSA's adaptive mechanism and cooperative behavior improve convergence speed and solution accuracy, making it more efficient for optimization in network reconfiguration.
- Open Access
- 11 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 151893-151906
A 3×3 Antenna Beamforming Network Based on Waveguide Nolen Matrix for Ka-Bands
The Fifth generation (5G) wireless communication system aims to provide high bandwidth, high sensitivity, high gain and power capability. Millimeter wave technology then proposed for these demands with various range of features such as higher bandwidth, low interference, and frequency reuse. However, millimeter wave technology has a key disadvantage of high path loss due to small wavelength in the channel of high attenuation coming from the atmosphere, in addition to the very small wavelength that produces an unwanted crosstalk between the transmission lines. Thus, beamforming network and waveguide-based structures such as Nolen matrix was proposed to overcome these problems. The objective of this research is to design a low loss and high-performance Nolen beamforming network based on waveguide technology. Taking in consideration is the advantage of flexible number of beam ports in Nolen matrix using single layer technique. This work aims to design a 3 × 3 Nolen matrix with main beam directions of 0, 30° and -30° at 26 GHz. The 3 × 3 Nolen matrix is designed using low loss hollow waveguide single layer technique. Then, the proposed Nolen matrix is fed three-waveguide slotted antenna. The proposed 3 × 3 Nolen matrix has measured phase differences at port 1 (35.40°), port 2 (156.43°) and port 3 (-93.57°) in the x-y plane. Waveguide slotted antenna has designed at 26 GHz with tilted slots at broad wall of the waveguide structure. This tilted technique has the benefit of increasing the bandwidth up to 50% of FBW. A simulation and measurement using CST software is performed for the proposed antenna. A return loss of -15 dB with wideband of 2.08 GHz are obtained. A gain of 14 dB is observed at broad wall respectively. Waveguide antenna has been integrated with Nolen matrix to build Nolen beamforming; the measured beamforming network has a good return loss of less than - 10 dB with phase error of -8 degree at outputs. Three beams are achieved with beam scanning of ± 30 degree. The beam from port 1 is radiated in the direction of -26°. The beams from port 2 and port 3 are radiated in the directions of +27° and +6° respectively. Therefore, this beamforming has a greater impact on the mm wave beamforming networks and applications.
- 11 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 151893-151906
Open AccessA 3×3 Antenna Beamforming Network Based on Waveguide Nolen Matrix for Ka-Bands
The Fifth generation (5G) wireless communication system aims to provide high bandwidth, high sensitivity, high gain and power capability. Millimeter wave technology then proposed for these demands with various range of features such as higher bandwidth, low interference, and frequency reuse. However, millimeter wave technology has a key disadvantage of high path loss due to small wavelength in the channel of high attenuation coming from the atmosphere, in addition to the very small wavelength that produces an unwanted crosstalk between the transmission lines. Thus, beamforming network and waveguide-based structures such as Nolen matrix was proposed to overcome these problems. The objective of this research is to design a low loss and high-performance Nolen beamforming network based on waveguide technology. Taking in consideration is the advantage of flexible number of beam ports in Nolen matrix using single layer technique. This work aims to design a 3 × 3 Nolen matrix with main beam directions of 0, 30° and -30° at 26 GHz. The 3 × 3 Nolen matrix is designed using low loss hollow waveguide single layer technique. Then, the proposed Nolen matrix is fed three-waveguide slotted antenna. The proposed 3 × 3 Nolen matrix has measured phase differences at port 1 (35.40°), port 2 (156.43°) and port 3 (-93.57°) in the x-y plane. Waveguide slotted antenna has designed at 26 GHz with tilted slots at broad wall of the waveguide structure. This tilted technique has the benefit of increasing the bandwidth up to 50% of FBW. A simulation and measurement using CST software is performed for the proposed antenna. A return loss of -15 dB with wideband of 2.08 GHz are obtained. A gain of 14 dB is observed at broad wall respectively. Waveguide antenna has been integrated with Nolen matrix to build Nolen beamforming; the measured beamforming network has a good return loss of less than - 10 dB with phase error of -8 degree at outputs. Three beams are achieved with beam scanning of ± 30 degree. The beam from port 1 is radiated in the direction of -26°. The beams from port 2 and port 3 are radiated in the directions of +27° and +6° respectively. Therefore, this beamforming has a greater impact on the mm wave beamforming networks and applications.
- Open Access
- 1 March 2024
- Published by Institute of Advanced Engineering and Science in IAES International Journal of Artificial Intelligence (IJ-AI)
- Vol. 13 (1) , 1172-1178
Convolutional neural network with binary moth flame optimization for emotion detection in electroencephalogram
Electroencephalograph (EEG) signals have the ability of real-time reflecting brain activities. Utilizing the EEG signal for analyzing human emotional states is a common study. The EEG signals of the emotions aren’t distinctive and it is different from one person to another as every one of them has different emotional responses to same stimuli. Which is why, the signals of the EEG are subject dependent and proven to be effective for the subject dependent detection of the Emotions. For the purpose of achieving enhanced accuracy and high true positive rate, the suggested system proposed a binary moth flame optimization (BMFO) algorithm for the process of feature selection and convolutional neural networks (CNNs) for classifications. In this proposal, optimum features are chosen with the use of accuracy as objective function. Ultimately, optimally chosen features are classified after that with the use of a CNN for the purpose of discriminating different emotion states.
- 1 March 2024
- Published by Institute of Advanced Engineering and Science in IAES International Journal of Artificial Intelligence (IJ-AI)
- Vol. 13 (1) , 1172-1178
Open AccessConvolutional neural network with binary moth flame optimization for emotion detection in electroencephalogram
Electroencephalograph (EEG) signals have the ability of real-time reflecting brain activities. Utilizing the EEG signal for analyzing human emotional states is a common study. The EEG signals of the emotions aren’t distinctive and it is different from one person to another as every one of them has different emotional responses to same stimuli. Which is why, the signals of the EEG are subject dependent and proven to be effective for the subject dependent detection of the Emotions. For the purpose of achieving enhanced accuracy and high true positive rate, the suggested system proposed a binary moth flame optimization (BMFO) algorithm for the process of feature selection and convolutional neural networks (CNNs) for classifications. In this proposal, optimum features are chosen with the use of accuracy as objective function. Ultimately, optimally chosen features are classified after that with the use of a CNN for the purpose of discriminating different emotion states.
- Open Access
- 13 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 7896-7910
Low Loss Wideband 4×4 Butler Matrix Networks Based on Substrate Integrated Waveguide for 5G Applications
Current wireless communications urgently need to provide huge data rates, high gain and high directivity radiation pattern beams. Therefore, beamforming networks (BFNs) are introduced to provide these needs. Butler matrix (BM) is a type of beamforming network, which can be realized using fixed network circuits and feeds the antenna array. BM at high frequency suffers from components loss and phase error for massive network, especially when it is implemented using common microstrip structures. Different transmission lines such as waveguide and substrate integrated waveguide (SIW) are studied and introduced to realize Butler matrix. SIW structures are good candidate for the implementation of BM due to its property of low loss transmission line which comprises of properties of microstrip and waveguide technology. However, SIW antennas and structures at millimetre waves have unwanted radiation loss coming from the vias holes. In addition, the vias separation distance is dependent on waveguide size, which leads to a more massive beamforming network at 26 GHz. Hence, this thesis is proposing a more size-friendly and optimal SIW antenna beamforming structure to reduce the vias loss and provides higher bandwidth and gain at 26 GHz. The BM components such as 3-dB coupler, 0-dB crossover, and 45-degree phase shifter are designed by implementing metallic vias determination method. Size and distance of vias are the most important factors in determining the coupling ratio and phase shifts at output ports. Hence, the coupler is designed with different vias width and distance to obtain the correct phase and coupling at output ports. Then, the designed coupler is cascaded to form a 0-dB crossover. The phase shifter is designed with alerting vias distance inside the coupling area of SIW structure. The last component in beamforming is the design of SIW slot antenna based on longitude slot distributions. All the components are integrated to form a 4 × 4 BM with four slot antennas attached to BM networks. Microtrip separation feedline used to for coupler, crossover, BM and BFN. The proposed designs are simulated using CST software and fabricated by PCB LPKF ProtoMat printer. The outcomes of wide bandwidth with more than 1 GHz and high directive gain of more than 10 dB for the beamforming network are achieved. The output power of the BM is between -6 dB to -8 dB at all four ports with phase difference error less than 5°. Four directive beams are achieved at beam scanning of -14°, -41°, 41°, and -14° at port 1 to port 4 respectively. Hence, this 4 × 4 BM with four slot antenna theses have introduced a successful design of an antenna beamforming network based on SIW technology with significant characteristics at 26 GHz.
- 13 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 7896-7910
Open AccessLow Loss Wideband 4×4 Butler Matrix Networks Based on Substrate Integrated Waveguide for 5G Applications
Current wireless communications urgently need to provide huge data rates, high gain and high directivity radiation pattern beams. Therefore, beamforming networks (BFNs) are introduced to provide these needs. Butler matrix (BM) is a type of beamforming network, which can be realized using fixed network circuits and feeds the antenna array. BM at high frequency suffers from components loss and phase error for massive network, especially when it is implemented using common microstrip structures. Different transmission lines such as waveguide and substrate integrated waveguide (SIW) are studied and introduced to realize Butler matrix. SIW structures are good candidate for the implementation of BM due to its property of low loss transmission line which comprises of properties of microstrip and waveguide technology. However, SIW antennas and structures at millimetre waves have unwanted radiation loss coming from the vias holes. In addition, the vias separation distance is dependent on waveguide size, which leads to a more massive beamforming network at 26 GHz. Hence, this thesis is proposing a more size-friendly and optimal SIW antenna beamforming structure to reduce the vias loss and provides higher bandwidth and gain at 26 GHz. The BM components such as 3-dB coupler, 0-dB crossover, and 45-degree phase shifter are designed by implementing metallic vias determination method. Size and distance of vias are the most important factors in determining the coupling ratio and phase shifts at output ports. Hence, the coupler is designed with different vias width and distance to obtain the correct phase and coupling at output ports. Then, the designed coupler is cascaded to form a 0-dB crossover. The phase shifter is designed with alerting vias distance inside the coupling area of SIW structure. The last component in beamforming is the design of SIW slot antenna based on longitude slot distributions. All the components are integrated to form a 4 × 4 BM with four slot antennas attached to BM networks. Microtrip separation feedline used to for coupler, crossover, BM and BFN. The proposed designs are simulated using CST software and fabricated by PCB LPKF ProtoMat printer. The outcomes of wide bandwidth with more than 1 GHz and high directive gain of more than 10 dB for the beamforming network are achieved. The output power of the BM is between -6 dB to -8 dB at all four ports with phase difference error less than 5°. Four directive beams are achieved at beam scanning of -14°, -41°, 41°, and -14° at port 1 to port 4 respectively. Hence, this 4 × 4 BM with four slot antenna theses have introduced a successful design of an antenna beamforming network based on SIW technology with significant characteristics at 26 GHz.
- Open Access
- 1 June 2022
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 11 (3) , 1390-1398
Design and characterization substrate integrated waveguide antenna for WBANS application
Millimetre-wave frequencies are defined as one of the front-runner contenders for body-centric wireless communication. In this study, low-profile antenna with the substrate integrated waveguide (SIW) has been proposed that operate in the band of the millimetre-wave frequency that has been centred at 60 GHz. The proposed antenna has been implemented with the use of the FR4 substrate with εr and tangent loss of 4.3 and 0.025, respectively. The substrate height and size are 1.5875 mm and 20 mm x 20 mm, respectively. The performance of the antenna is evaluated in off-body (free space) and on-body (human voxel model), through simulation. The proposed antenna has an ultra-wideband (UWB) and a specific absorption rate the maximal (SAR) for (10 g) is 0.0344815 W/kg and for (1 g) is 0.0184723 W/kg. It achieves 74% and 63% efficiency in the off and on-body scenario, respectively. The small antenna with the exceptional matching of impedance, low SAR, broad bandwidth, and good efficiency, a good voltage standing wave ratio good (VSWR), and good front-to-back ratio (FBR). As a result, its characteristics make it one of the best potential candidates for the simultaneous transmission and reception of data at (mm-wave) band for WBAN applications.
- 1 June 2022
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 11 (3) , 1390-1398
Open AccessDesign and characterization substrate integrated waveguide antenna for WBANS application
Millimetre-wave frequencies are defined as one of the front-runner contenders for body-centric wireless communication. In this study, low-profile antenna with the substrate integrated waveguide (SIW) has been proposed that operate in the band of the millimetre-wave frequency that has been centred at 60 GHz. The proposed antenna has been implemented with the use of the FR4 substrate with εr and tangent loss of 4.3 and 0.025, respectively. The substrate height and size are 1.5875 mm and 20 mm x 20 mm, respectively. The performance of the antenna is evaluated in off-body (free space) and on-body (human voxel model), through simulation. The proposed antenna has an ultra-wideband (UWB) and a specific absorption rate the maximal (SAR) for (10 g) is 0.0344815 W/kg and for (1 g) is 0.0184723 W/kg. It achieves 74% and 63% efficiency in the off and on-body scenario, respectively. The small antenna with the exceptional matching of impedance, low SAR, broad bandwidth, and good efficiency, a good voltage standing wave ratio good (VSWR), and good front-to-back ratio (FBR). As a result, its characteristics make it one of the best potential candidates for the simultaneous transmission and reception of data at (mm-wave) band for WBAN applications.