Hazwaj Mhd Poad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hazwaj Mhd Poad has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Afarulrazi Abu Bakar
Universiti Tun Hussein Onn Malaysia
3 shared publications - Tharnisha Sithananthan
Universiti Tun Hussein Onn Malaysia
2 shared publications - Abd Kadir Mahamad
Universiti Tun Hussein Onn Malaysia
1 shared publication - Ahmad Faiz Abdul Ghani
University Tun Hussein Onn Malaysia
1 shared publication Ahmad Zahid Zakwan Bin Abdul Karim
Universiti Tun Hussein Onn Malaysia
1 shared publication- Balarajan Sannasy
Universiti Tun Hussein Onn Malaysia
1 shared publication
Latest Publications
- Open Access
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 17 (2)
Design of 7-level cascade asymmetric multilevel inverter for renewable energy applications using FPGA
The increasing focus on renewable energy has driven the need for efficient and reliable power converters. Multilevel inverters offer low harmonic distortion and high-quality output but often suffer from design complexity and excessive component count. This study presents the design and implementation of a 7-level cascaded asymmetric multilevel inverter optimized for renewable energy applications. The proposed topology utilizes a cascade structure with asymmetric DC voltage sources to generate seven voltage levels, providing a practical balance between performance and simplicity. The design was first validated through MATLAB/Simulink software to analyze circuit operation and evaluate the total harmonic distortion (THD) performance. Experimental evaluation was then conducted using a hardware prototype to verify simulation results. Without a filter, the THD from the simulation was 21.31%, while the experimental setup recorded a slightly higher value of 21.61%, indicating a marginal difference of 0.21%. With a filter, the simulation achieved a THD of 3.81%, whereas the experimental setup outperformed with a THD of 1.5%, showing a notable reduction of 2.31%. These findings confirm the proposed inverter’s capability to deliver superior power quality and operational efficiency. The combination of simulation and experimental validation demonstrates the practicality and reliability of the 7-level cascade asymmetric multilevel inverter for renewable energy applications.
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 17 (2)
Open AccessDesign of 7-level cascade asymmetric multilevel inverter for renewable energy applications using FPGA
The increasing focus on renewable energy has driven the need for efficient and reliable power converters. Multilevel inverters offer low harmonic distortion and high-quality output but often suffer from design complexity and excessive component count. This study presents the design and implementation of a 7-level cascaded asymmetric multilevel inverter optimized for renewable energy applications. The proposed topology utilizes a cascade structure with asymmetric DC voltage sources to generate seven voltage levels, providing a practical balance between performance and simplicity. The design was first validated through MATLAB/Simulink software to analyze circuit operation and evaluate the total harmonic distortion (THD) performance. Experimental evaluation was then conducted using a hardware prototype to verify simulation results. Without a filter, the THD from the simulation was 21.31%, while the experimental setup recorded a slightly higher value of 21.61%, indicating a marginal difference of 0.21%. With a filter, the simulation achieved a THD of 3.81%, whereas the experimental setup outperformed with a THD of 1.5%, showing a notable reduction of 2.31%. These findings confirm the proposed inverter’s capability to deliver superior power quality and operational efficiency. The combination of simulation and experimental validation demonstrates the practicality and reliability of the 7-level cascade asymmetric multilevel inverter for renewable energy applications.
- Open Access
- 1 December 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (4) , 2452-2461
Digitally fast synchronization of single-phase grid-tied inverter using FPGA
As interest in alternative energy sources grows, grid-connected inverters are getting more advanced. Thus, to synchronize the output waveform of an inverter with the grid supply system, the frequency and phase angle ought to be consistent. This paper presents an enhanced digital implementation controller for a grid-connected inverter using the sinusoidal pulse-width modulation (SPWM) switching technique via an appropriately designed low-pass filter. The main contribution of the proposed digital controller algorithm is to synchronize with the grid for the next half-cycle. The proposed control technique used the integrated response from the zero-crossing detector (ZCD) circuit for every half-cycle to trigger the digital phase-locked loop (PLL) implemented using field-programmable gate array (FPGA). An experimental 100 W single-phase full-bridge inverter prototype tested and validated the proposed control algorithm to prove the switching approach works. From the experimental results, the proposed control algorithm demonstrates synchronization with the grid voltage within 8 ms during startup. Furthermore, it exhibits the ability to adapt to phase changes when subjected to a distorted grid, achieving synchronization within 42 ms. This research also emphasizes synchronization between the grid waveform and the inverter output via the phase angle difference.
- 1 December 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (4) , 2452-2461
Open AccessDigitally fast synchronization of single-phase grid-tied inverter using FPGA
As interest in alternative energy sources grows, grid-connected inverters are getting more advanced. Thus, to synchronize the output waveform of an inverter with the grid supply system, the frequency and phase angle ought to be consistent. This paper presents an enhanced digital implementation controller for a grid-connected inverter using the sinusoidal pulse-width modulation (SPWM) switching technique via an appropriately designed low-pass filter. The main contribution of the proposed digital controller algorithm is to synchronize with the grid for the next half-cycle. The proposed control technique used the integrated response from the zero-crossing detector (ZCD) circuit for every half-cycle to trigger the digital phase-locked loop (PLL) implemented using field-programmable gate array (FPGA). An experimental 100 W single-phase full-bridge inverter prototype tested and validated the proposed control algorithm to prove the switching approach works. From the experimental results, the proposed control algorithm demonstrates synchronization with the grid voltage within 8 ms during startup. Furthermore, it exhibits the ability to adapt to phase changes when subjected to a distorted grid, achieving synchronization within 42 ms. This research also emphasizes synchronization between the grid waveform and the inverter output via the phase angle difference.
- Open Access
- 1 June 2022
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 11 (3) , 1723-1734
Power losses analysis of multiphase DC-DC buck converter using OrCAD PSpice software
DC-DC buck converters have wide applications in portable electronic devices, battery chargers, and telecommunications. However, single-phase DC-DC buck converters have some drawbacks, especially in high current applications, where the increase in the size of the inductor will increase power losses, which significantly affects the overall efficiency of the converter. The multiphase configuration offers several advantages, such as reduction in output voltage ripple, input current ripple, conduction loss, and the physical size of the hardware. This paper presents an analysis of the power losses of the multiphase DC-DC buck converter with output power ranging between 50 watts to 250 watts. To verify the effectiveness of the multiphase converter, performance analysis was done using OrCAD PSpice software, where the number of phases was limited to five phases. This paper focused on power losses in the converter, namely conduction losses in diodes and MOSFETs, switching loss in MOSFETs, as well as losses in the inductor and capacitor. The relationship between the number of phases and factors of switching frequency, output, and the components’ internal resistance was also highlighted and discussed in detail.
- 1 June 2022
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 11 (3) , 1723-1734
Open AccessPower losses analysis of multiphase DC-DC buck converter using OrCAD PSpice software
DC-DC buck converters have wide applications in portable electronic devices, battery chargers, and telecommunications. However, single-phase DC-DC buck converters have some drawbacks, especially in high current applications, where the increase in the size of the inductor will increase power losses, which significantly affects the overall efficiency of the converter. The multiphase configuration offers several advantages, such as reduction in output voltage ripple, input current ripple, conduction loss, and the physical size of the hardware. This paper presents an analysis of the power losses of the multiphase DC-DC buck converter with output power ranging between 50 watts to 250 watts. To verify the effectiveness of the multiphase converter, performance analysis was done using OrCAD PSpice software, where the number of phases was limited to five phases. This paper focused on power losses in the converter, namely conduction losses in diodes and MOSFETs, switching loss in MOSFETs, as well as losses in the inductor and capacitor. The relationship between the number of phases and factors of switching frequency, output, and the components’ internal resistance was also highlighted and discussed in detail.
- 10 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Anti-Collision Car System using Fuzzy Logic Technique
This work proposed to design anti-collision car system that could predict the collision using fuzzy logic, controlled by PIC16F877A with pulse width modulation (PWM) technique. The ultrasonic sensor and humidity sensor are used to measure the distance and detect the relative humidity (RH) of the road condition. PWM duty ratio of a moving and stop condition of the vehicle are indicated with a value of > 70% and < 40%, respectively. For a dangerous situation, the DC motor is turned off and the LED display is turned on as a warning to the driver.
- 10 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Anti-Collision Car System using Fuzzy Logic Technique
This work proposed to design anti-collision car system that could predict the collision using fuzzy logic, controlled by PIC16F877A with pulse width modulation (PWM) technique. The ultrasonic sensor and humidity sensor are used to measure the distance and detect the relative humidity (RH) of the road condition. PWM duty ratio of a moving and stop condition of the vehicle are indicated with a value of > 70% and < 40%, respectively. For a dangerous situation, the DC motor is turned off and the LED display is turned on as a warning to the driver.
- Open Access
- 1 July 2018
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 11 (1) , 152-160
Smart Home Security Access System Using Field Programmable Gate Arrays
Nowadays, the rapid growth of burglary and theft cases over the world has been threatening to the vulnerability of traditional home security systems. Therefore the development home security with intelligent control wherein focus to enhance conventional technique to theadvanced digital security systemand to be more interestinginhome or building owner for preventing intruders in smart home implementation. However, using avariety of type conventional lock doors for security purposes and analog intruder sensor with individual function system is not secure enoughin order to protect the person or company properties. That why the emergence of new technology such as integrated circuit network will apply in Smart Home system for abetter security solution to prevent the houses from theintruder and hazardous fire incident. Therefore, this project is done to design and build a smart system with consist of digital security entry for automatic lock doors and also for activating or deactivate all security sensor in houses which is function for detecting the irregular movement and hot temperature (fire incident) in-house for the domestic residential sector. This product includeswith doors automatic lock system using servo motor and detect irregular movement intruder using PIR motion sensor (HC-SR501) and also measure hot temperature using temperature sensor (LM35). The sensor will transmit theanalog signal to Field Programmable Gate Array (FPGA) the Altera DE2-115 board to be processed and which will then display the status entry after key-in password and activation security system on the LED seven segment displays. The entry login controller will use apush button or switchesavailable on FPGA board that are used to login password for automatic door accessand also able maintained for control home smart security system.
- 1 July 2018
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 11 (1) , 152-160
Open AccessSmart Home Security Access System Using Field Programmable Gate Arrays
Nowadays, the rapid growth of burglary and theft cases over the world has been threatening to the vulnerability of traditional home security systems. Therefore the development home security with intelligent control wherein focus to enhance conventional technique to theadvanced digital security systemand to be more interestinginhome or building owner for preventing intruders in smart home implementation. However, using avariety of type conventional lock doors for security purposes and analog intruder sensor with individual function system is not secure enoughin order to protect the person or company properties. That why the emergence of new technology such as integrated circuit network will apply in Smart Home system for abetter security solution to prevent the houses from theintruder and hazardous fire incident. Therefore, this project is done to design and build a smart system with consist of digital security entry for automatic lock doors and also for activating or deactivate all security sensor in houses which is function for detecting the irregular movement and hot temperature (fire incident) in-house for the domestic residential sector. This product includeswith doors automatic lock system using servo motor and detect irregular movement intruder using PIR motion sensor (HC-SR501) and also measure hot temperature using temperature sensor (LM35). The sensor will transmit theanalog signal to Field Programmable Gate Array (FPGA) the Altera DE2-115 board to be processed and which will then display the status entry after key-in password and activation security system on the LED seven segment displays. The entry login controller will use apush button or switchesavailable on FPGA board that are used to login password for automatic door accessand also able maintained for control home smart security system.