Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Abdelhak Hamid Allah has a total of 3 co-authors. Here are the top co-authors by number of shared publications:

  • Guy Ayissi Eyebe

    Department of Electrical and Computer Engineering, Université du Québec à Trois-Rivières, Trois-Rivières, QC G9A 5H7, Canada

    2 shared publications
  • Frederic Domingue

    Department of Electrical and Computer Engineering, Universit du Qubec Trois-Rivires, Trois-Rivires, QC, Canada

    1 shared publication
  • Frederic Domingue

    Laboratoire de Technologies et dInnovation pour la Performance Sportive, Universit du Qubec Trois-Rivires, Trois-Rivires, QC, Canada

    1 shared publication

Latest Publications

  • Open Access

    Improved Fully 3D-Printed SIW-Based Sensor for Non-Invasive Glucose Measurement

    by Abdelhak Hamid Allah, Guy Ayissi Eyebe, Frédéric Domingue

    This paper presents a fully 3D-printed microfluidic microwave sensor based on substrate-integrated waveguide (SIW) technology for detecting glucose levels in liquid, aimed at monitoring diabetic patients. The sensor’s design features a circular SIW cavity with an integrated sample holder placed in the cavity’s center, maximizing the electric field disturbance from the liquid under test (LUT). Operating in the TM010 mode at a resonance frequency around 5.740 GHz, the sensor detects glucose concentrations by measuring resonance frequency shifts in the S11 reflection response across glucose levels. A conductive sheath partially covers the sample holder to enhance sensitivity and improve the limit of detection (LOD) by increasing field penetration into the LUT. Fabricated using an additive manufacturing electronics (AMEs) method, the sensor is produced in a single pass without post-processing. The experimental validation confirms its high sensitivity of 1.218 MHz/(mg/dL) and a low limit of detection of 0.774 mg/dL in the glucose concentration range (10–200 mg/dL), reflecting typical Type 2 diabetes levels. The key advantages of the sensor include its compactness, enhanced sensitivity and limit of detection, innovative manufacturing, and cost-effectiveness, supporting its potential as a non-invasive glucose monitoring tool. This study establishes a proof of concept for the in vitro measurement of glucose, demonstrating the sensor’s ability to provide accurate and reliable results in a controlled environment.


  • Fully 3D-Printed Microfluidic Sensor Using Substrate Integrated Waveguide Technology for Liquid Permittivity Characterization

    by Abdelhak Hamid Allah, Guy Ayissi Eyebe, Frederic Domingue

    This paper proposes a fully 3D-printed electromagnetic (EM) microfluidic sensor using rectangular substrate integrated waveguide (SIW) for liquid complex permittivity characterization. The proposed microfluidic sensor is fabricated with a novel additive manufacturing process in which dielectric and conductive inks are simultaneously 3D-printed, allowing high print quality, rapid prototyping, and arbitrary geometry. The fabrication process removes the need for post-printing sintering and cleaning steps that require harmful chemicals. The sensor structure is composed of upper and lower metal plates and a series of cylindrical metal side vias. Since the electric field is high at the center of the SIW cavity in $\textit {TE}_{101}$ mode, a cylindrical dielectric sample container in the form of a microwell is built into the center of the SIW cavity to maximize the perturbation of the liquid under test (LUT). The application of LUT samples to the microwell results in a change in the resonance frequency and peak attenuation from which the LUT sample is characterized. Ethanol-water mixtures are used as LUTs for validation. The proposed sensor has been verified numerically and experimentally, reducing the resonant frequency from 3.750 GHz to 3.862 GHz by increasing the ethanol volume fraction from 0% to 100%. The sensor showed good sensitivity of 0.345% and a stable frequency change was observed over five measurement repetitions. To the best of our knowledge, this article presents the first fully 3D-printed SIW microfluidic sensor and demonstrates its ability to detect and characterize the liquid complex permittivity.