I Wayan Adiyasa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
I Wayan Adiyasa has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Aan Yudianto
Universitas Negeri Yogyakarta
3 shared publications - Afri Yudantoko
Department of Automotive Engineering Education, Universitas Negeri Yogyakarta, Indonesia
1 shared publication Agus Puji Prasetyono
Universitas Negeri Yogyakarta
1 shared publication- Eka Firmansyah
Department of Electrical and Information Engineering, Faculty of Engineering, Universitas Gadjah Mada (UGM), Yogyakarta, Indonesia
1 shared publication - Fransisco Danang Wijaya
Department of Electrical and Information Engineering, Universitas Gadjah Mada, Yogyakarta, Indonesia
1 shared publication Moch Solikin
Universitas Negeri Yogyakarta
1 shared publication
Latest Publications
- 24 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 177-182
BLDC Motor Sizing Analysis on P1 Topology Hybridization of Single Cylinder ICE
The hybridization process of a motorcycle with a P1 configuration identifies the performance of an electric motor at the same speed point or more on an internal combustion engine (ICE). The targeted speed is the highest torque point on the ICE. This condition is often called torque assist. Most starter motors on conventional motorcycles operate at cranking speed. The use of starter motors in the latest technology uses a BLDC electric motor. The advancement of controllers and starter motor topology enables the BLDC electric motor to run at its maximum torque point speed on the ICE. Generally., ICE designs that have BLDC electric motors use P1 hybrid topology or are often called integrated starter-generator (ISG). The paper focuses on the analysis of the sizing of BLDC electric motors to be able to operate as ISGs at the highest torque point speed on the ICE. The constraints in the paper are in the form of operating voltage parameters., wire diameter., and number of turns. Changes in these values achieve a greater motor torque equal to its base torque and a motor speed greater than its base speed. The sizing results show an increase in speed of up to 3000 rpm with operating temperature conditions for 60 minutes maintained at 50.2 °C. The reduction in fuel consumption during vehicle dynamics testing reached 1,376% in the ECE-R15 driving cycle, 1,033 in the ECE-R40 driving cycle, and 1,217 in the WMTC driving cycle.
- 24 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 177-182
BLDC Motor Sizing Analysis on P1 Topology Hybridization of Single Cylinder ICE
The hybridization process of a motorcycle with a P1 configuration identifies the performance of an electric motor at the same speed point or more on an internal combustion engine (ICE). The targeted speed is the highest torque point on the ICE. This condition is often called torque assist. Most starter motors on conventional motorcycles operate at cranking speed. The use of starter motors in the latest technology uses a BLDC electric motor. The advancement of controllers and starter motor topology enables the BLDC electric motor to run at its maximum torque point speed on the ICE. Generally., ICE designs that have BLDC electric motors use P1 hybrid topology or are often called integrated starter-generator (ISG). The paper focuses on the analysis of the sizing of BLDC electric motors to be able to operate as ISGs at the highest torque point speed on the ICE. The constraints in the paper are in the form of operating voltage parameters., wire diameter., and number of turns. Changes in these values achieve a greater motor torque equal to its base torque and a motor speed greater than its base speed. The sizing results show an increase in speed of up to 3000 rpm with operating temperature conditions for 60 minutes maintained at 50.2 °C. The reduction in fuel consumption during vehicle dynamics testing reached 1,376% in the ECE-R15 driving cycle, 1,033 in the ECE-R40 driving cycle, and 1,217 in the WMTC driving cycle.
- Open Access
- 8 May 2023
- Published by Universitas Bina Nusantara in ComTech: Computer, Mathematics and Engineering Applications
- Vol. 14 (1) , 21-32
Lightweight Design and Finite Element Analysis of Brake Lever for Motorcycle Application
A lightweight component design contributes to the overall optimization of a system to be more effective and efficient. Then, it can lead to the contribution of a carbon footprint reduction. The research aimed to propose a novel lightweight brake lever design for motorcycle applications and numerically investigate its performance by comparing the proposed design with different utilized materials. The subject of the research was an optimized brake lever for motorcycle application. The materials used were aluminum alloy, structural steel, and titanium alloy. A Finite Element Method (FEM) analysis was employed to investigate the proposed brake lever design. Three proposed designs were introduced with the mass reduction in each optimization up to 50,9% of reduced mass. Maximum stress was observed on the most optimized design with a value of 297 MPa. The strain and total deformation were also investigated among the components. In the result, the stress-strain graph shows that the most optimized brake lever experiences the highest stress with the highest strain value. Furthermore, the highest safety factor is achieved with the utilization of titanium alloy, reaching the value of 6,28 for preliminary design and 3,1 for the most optimized component. However, the lightest component can be obtained using aluminum alloy.
- 8 May 2023
- Published by Universitas Bina Nusantara in ComTech: Computer, Mathematics and Engineering Applications
- Vol. 14 (1) , 21-32
Open AccessLightweight Design and Finite Element Analysis of Brake Lever for Motorcycle Application
A lightweight component design contributes to the overall optimization of a system to be more effective and efficient. Then, it can lead to the contribution of a carbon footprint reduction. The research aimed to propose a novel lightweight brake lever design for motorcycle applications and numerically investigate its performance by comparing the proposed design with different utilized materials. The subject of the research was an optimized brake lever for motorcycle application. The materials used were aluminum alloy, structural steel, and titanium alloy. A Finite Element Method (FEM) analysis was employed to investigate the proposed brake lever design. Three proposed designs were introduced with the mass reduction in each optimization up to 50,9% of reduced mass. Maximum stress was observed on the most optimized design with a value of 297 MPa. The strain and total deformation were also investigated among the components. In the result, the stress-strain graph shows that the most optimized brake lever experiences the highest stress with the highest strain value. Furthermore, the highest safety factor is achieved with the utilization of titanium alloy, reaching the value of 6,28 for preliminary design and 3,1 for the most optimized component. However, the lightest component can be obtained using aluminum alloy.
- Open Access
- 24 January 2023
- Published by Universitas Negeri Yogyakarta in Jurnal Pendidikan Vokasi Otomotif
- Vol. 5 (1) , 27-42
IMPROVISASI TORSI DAN EFISIENSI PADA REDESAIN MOTOR BRUSHLESS DC HOVERBOARD BERDAYA DASAR 350W
IMPROVISASI TORSI DAN EFISIENSI PADA REDESAIN MOTOR BRUSHLESS DC HOVERBOARD BERDAYA DASAR 350W
- 24 January 2023
- Published by Universitas Negeri Yogyakarta in Jurnal Pendidikan Vokasi Otomotif
- Vol. 5 (1) , 27-42
Open AccessIMPROVISASI TORSI DAN EFISIENSI PADA REDESAIN MOTOR BRUSHLESS DC HOVERBOARD BERDAYA DASAR 350W
IMPROVISASI TORSI DAN EFISIENSI PADA REDESAIN MOTOR BRUSHLESS DC HOVERBOARD BERDAYA DASAR 350W
- Open Access
- 27 May 2022
- Published by Universitas Negeri Yogyakarta in Jurnal Pendidikan Teknologi dan Kejuruan
- Vol. 28 (1) , 121-129
The Development of Learning Media of 2-Stroke Engine Manufactured by 3D Print for Distance Learning
The Covid19 pandemic that has hit the world requires educational media innovations that are portable, lightweight, and easy to operate for online learning purposes. This study aims to develop learning media for students of the Light Vehicle Engineering Vocational School on the topic of a 2 stroke engine using a engine model made using 3D printing technology with Polylactic Acid as the base material. This is carried out to develop media to support teachers of related subjects in the implementation of online learning. This study uses the Design and Development (DD Research) method which consists of identifying the problem, describing the objectives, design and development, testing, evaluating and finally communicating the results. Data analysis was carried out quantitatively and qualitatively to explain the obtained results. The checklist evaluation was performed to assess the produced learning media. The results indicated that the utilization of 3D print to create lightweight, portable and representable learning media has been successfully achieved. The constructed learning media is aimed to be utilized to explain the competency of two-strokes engine in a distance learning.
- 27 May 2022
- Published by Universitas Negeri Yogyakarta in Jurnal Pendidikan Teknologi dan Kejuruan
- Vol. 28 (1) , 121-129
Open AccessThe Development of Learning Media of 2-Stroke Engine Manufactured by 3D Print for Distance Learning
The Covid19 pandemic that has hit the world requires educational media innovations that are portable, lightweight, and easy to operate for online learning purposes. This study aims to develop learning media for students of the Light Vehicle Engineering Vocational School on the topic of a 2 stroke engine using a engine model made using 3D printing technology with Polylactic Acid as the base material. This is carried out to develop media to support teachers of related subjects in the implementation of online learning. This study uses the Design and Development (DD Research) method which consists of identifying the problem, describing the objectives, design and development, testing, evaluating and finally communicating the results. Data analysis was carried out quantitatively and qualitatively to explain the obtained results. The checklist evaluation was performed to assess the produced learning media. The results indicated that the utilization of 3D print to create lightweight, portable and representable learning media has been successfully achieved. The constructed learning media is aimed to be utilized to explain the competency of two-strokes engine in a distance learning.
- Open Access
- 14 August 2021
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 4 (3) , 119-130
Aerodynamics of Bus Platooning under Crosswind
The aerodynamic benefits of a vehicle in a platoon could be distracted by an imposed crosswind on it. The study aims to investigate the alteration of aerodynamic coefficient comprising drag force coefficient, lift force coefficient, side force coefficient, and pressure coefficient of buses traveling in a platoon by considering crosswind. A Computational Fluid Dynamic (CFD) simulation was carried out on a detailed bus model. Proposed meshing techniques were also offered. The investigation considered the yaw angle from 0° to 30° and inter-bus distances by proposed coefficient X/L from 0.05 to 1.25. The results in the changes in the aerodynamic performance of both buses were presented. The advantages of platoon configuration were described in more detail when no crosswind was considered in terms of the generated turbulence kinetic energy of the leading and following bus. The results indicated that a crosswind deteriorates aerodynamic benefits during the platoon. The inter-bus distance determines how the airflow around the bus behaves, leading to the variation in aerodynamic advantages experienced by buses. Comparison between the numerical study and experiment indicated a satisfactory correlation of results validation.
- 14 August 2021
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 4 (3) , 119-130
Open AccessAerodynamics of Bus Platooning under Crosswind
The aerodynamic benefits of a vehicle in a platoon could be distracted by an imposed crosswind on it. The study aims to investigate the alteration of aerodynamic coefficient comprising drag force coefficient, lift force coefficient, side force coefficient, and pressure coefficient of buses traveling in a platoon by considering crosswind. A Computational Fluid Dynamic (CFD) simulation was carried out on a detailed bus model. Proposed meshing techniques were also offered. The investigation considered the yaw angle from 0° to 30° and inter-bus distances by proposed coefficient X/L from 0.05 to 1.25. The results in the changes in the aerodynamic performance of both buses were presented. The advantages of platoon configuration were described in more detail when no crosswind was considered in terms of the generated turbulence kinetic energy of the leading and following bus. The results indicated that a crosswind deteriorates aerodynamic benefits during the platoon. The inter-bus distance determines how the airflow around the bus behaves, leading to the variation in aerodynamic advantages experienced by buses. Comparison between the numerical study and experiment indicated a satisfactory correlation of results validation.