Paulson Samuel
Research Subjects
Paulson Samuel has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Rajesh Gupta
Motilal Nehru National Institute of Technology Allahabad
3 shared publications - Akhilesh Kumar Gupta
MNNIT Allahabad
2 shared publications Majhrul Israr
2 shared publications- Raj Kapur Kumar
MNNIT Allahabad
2 shared publications - Soumya Ranjan Mohanty
Electrical Engineering Department, Indian Institute of Technology (BHU), Varanasi, India
2 shared publications - Vivek Kumar Yadav2 shared publications
Latest Publications
- 21 November 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 197
Efficient solar hydrogen generation using PEM electrolysis in a grid-connected system
- 21 November 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 197
Efficient solar hydrogen generation using PEM electrolysis in a grid-connected system
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. 71 (4) , 10349-10360
An Intelligent Controller With Improved Power Quality of Boost PFC Converter for Light EV Charger Application
Traditional ACM (average current mode) control for the CCM boost PFC converter, which incorporates LPF (low pass filter) in the voltage loop, encounters challenges such as limited bandwidth and the effect of DLF (double-line frequency) ripple on the reference signal for the current control loop. Additionally, the PI current controller exhibits slow dynamic response near the zero-crossing point, leading to inaccuracies in reference current tracking and causing zero-crossing distortion (ZCD). These challenges result in a low PF, high THD, and slow dynamic performance. To overcome these challenges, this work introduces an intelligent PFC controller that generates quick and high-quality reference current utilizing supply voltage and output power from the power balance equation. This approach mitigates the limitations of a low-bandwidth voltage loop, the DLF effect on the reference signal, and enhances dynamic performance. Additionally, a particle swarm optimization (PSO)-optimized IP current controller is integrated into the proposed dual-loop control structure to minimize reference tracking errors and eliminate ZCD, leading to improved source current power quality and overall performance. The efficacy of the controller is tested in MATLAB software, and experimental verification is done by a 500 W CCM boost PFC converter prototype over a dSPACE DS 1104 real-time control platform.
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. 71 (4) , 10349-10360
An Intelligent Controller With Improved Power Quality of Boost PFC Converter for Light EV Charger Application
Traditional ACM (average current mode) control for the CCM boost PFC converter, which incorporates LPF (low pass filter) in the voltage loop, encounters challenges such as limited bandwidth and the effect of DLF (double-line frequency) ripple on the reference signal for the current control loop. Additionally, the PI current controller exhibits slow dynamic response near the zero-crossing point, leading to inaccuracies in reference current tracking and causing zero-crossing distortion (ZCD). These challenges result in a low PF, high THD, and slow dynamic performance. To overcome these challenges, this work introduces an intelligent PFC controller that generates quick and high-quality reference current utilizing supply voltage and output power from the power balance equation. This approach mitigates the limitations of a low-bandwidth voltage loop, the DLF effect on the reference signal, and enhances dynamic performance. Additionally, a particle swarm optimization (PSO)-optimized IP current controller is integrated into the proposed dual-loop control structure to minimize reference tracking errors and eliminate ZCD, leading to improved source current power quality and overall performance. The efficacy of the controller is tested in MATLAB software, and experimental verification is done by a 500 W CCM boost PFC converter prototype over a dSPACE DS 1104 real-time control platform.
- 4 November 2024
- Published by Elsevier in Computers and Electrical Engineering
- Vol. 120
High-performance front end PFC controller design for light electric vehicle charger application
- 4 November 2024
- Published by Elsevier in Computers and Electrical Engineering
- Vol. 120
High-performance front end PFC controller design for light electric vehicle charger application
- 13 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 20 (5) , 7325-7334
Intelligent Fault Detection and Classification for an Unbalanced Network With Inverter-Based DG Units
In this article, a machine-learning-based fault detection and classification method is proposed. Two supervised learning-based protection modules are developed for the relays considered in the study—one to detect the fault and discriminate between the symmetrical or unsymmetrical nature of the fault and another to detect the faulty phase(s). A robust set of features using both relay voltage and current signals is utilized for developing the modules. The features are obtained using the multiresolution decomposition based on the empirical wavelet transform. The modules are tested on the unbalanced IEEE 13-node network integrated with inverter-based distributed generation systems capable of reactive power injection in the low-voltage ride-through mode of operation. Varying penetration levels and intermittent output of distributed generation, fault resistance, fault inception time, noise in the signals, and switching events occurring around the fault period are some of the unique operating scenarios considered to demonstrate the consistent performance of the relays. The simulations are performed in power systems computer aided design/electromagnetic transients including DC (PSCAD/EMTDC) and the protection modules are developed in MATLAB. The performance of the protection modules is evaluated using several metrics with respect to various classes of events occurring in the network.
- 13 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 20 (5) , 7325-7334
Intelligent Fault Detection and Classification for an Unbalanced Network With Inverter-Based DG Units
In this article, a machine-learning-based fault detection and classification method is proposed. Two supervised learning-based protection modules are developed for the relays considered in the study—one to detect the fault and discriminate between the symmetrical or unsymmetrical nature of the fault and another to detect the faulty phase(s). A robust set of features using both relay voltage and current signals is utilized for developing the modules. The features are obtained using the multiresolution decomposition based on the empirical wavelet transform. The modules are tested on the unbalanced IEEE 13-node network integrated with inverter-based distributed generation systems capable of reactive power injection in the low-voltage ride-through mode of operation. Varying penetration levels and intermittent output of distributed generation, fault resistance, fault inception time, noise in the signals, and switching events occurring around the fault period are some of the unique operating scenarios considered to demonstrate the consistent performance of the relays. The simulations are performed in power systems computer aided design/electromagnetic transients including DC (PSCAD/EMTDC) and the protection modules are developed in MATLAB. The performance of the protection modules is evaluated using several metrics with respect to various classes of events occurring in the network.
- 17 December 2019
- Published by Springer Nature
- p. 247-256
Speed Control of PMSM Drive Using Jaya Optimization Based Model Reduction
- 17 December 2019
- Published by Springer Nature
- p. 247-256
Speed Control of PMSM Drive Using Jaya Optimization Based Model Reduction
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Stability Assessment and Robust Controller Design of Grid Interactive Offshore Wind Farm and Marine Current Farm using STATCOM
In the context of larger renewable energy harnessing, combining offshore wind farm (OWF) and marine current farm (MCF) at the same location is often found suitable in terms of geographical conditions as well as economic reasons. However stochastic nature of resource with increased penetration level requires thorough investigation of the system stability issues. In this article, a robust controller for the integrated system is carried out in presence of parametric uncertainty. In this contest effort is made linearizen on-linear plant dynamics with wide range variation of operating point and uncertainties associated. The efficacy of the proposed control scheme is carried out through different case studies in real time digital simulation (RTDS) environment. The comparative analysis of simulation results demonstrates the effectiveness of the proposed control strategy in context of integrated system stability and reliability.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Stability Assessment and Robust Controller Design of Grid Interactive Offshore Wind Farm and Marine Current Farm using STATCOM
In the context of larger renewable energy harnessing, combining offshore wind farm (OWF) and marine current farm (MCF) at the same location is often found suitable in terms of geographical conditions as well as economic reasons. However stochastic nature of resource with increased penetration level requires thorough investigation of the system stability issues. In this article, a robust controller for the integrated system is carried out in presence of parametric uncertainty. In this contest effort is made linearizen on-linear plant dynamics with wide range variation of operating point and uncertainties associated. The efficacy of the proposed control scheme is carried out through different case studies in real time digital simulation (RTDS) environment. The comparative analysis of simulation results demonstrates the effectiveness of the proposed control strategy in context of integrated system stability and reliability.