Zeyu Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zeyu Chen has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Balaji Raghothamachar
Stony Brook University
20 shared publications - Michael Dudley
Stony Brook University
19 shared publications - Shanshan Hu
Stony Brook University
17 shared publications - Yafei Liu
Stony Brook University
8 shared publications - Qianyu Cheng
Stony Brook University
6 shared publications - Hao Chi Wang
Stony Brook University
4 shared publications
Latest Publications
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1190, 55-62
Investigation of Spoke Pattern of Stacking Faults in 4H-SiC Wafers Grown by Physical Vapor Transport Method
Synchrotron monochromatic beam X-ray topography (SMBXT), synchrotron white beam X-ray topography (SWBXT) and high-resolution X-ray topography (HRXRT) were used to characterize a series of wafers sliced from two PVT-grown 4H-SiC boules under similar growth conditions. A unique spoke-shaped distribution of the threading screw/mixed dislocations (TSDs/TMDs) density map can be observed from wafers sliced from later stages of growth of both boules. Systematic sequential analysis of the SMBXT grazing incidence images and HRXRT reflection images of the wafers reveals the spoke patterns are formed due to continuous deflection process of TSDs/TMDs by thin layer of polytypes that propagate along step flow direction and expand vertically, leading to TSD density difference across the wafer. Regions with high TSD densities have higher growth rate, resulting in a ridge and valley structure. Generation of macrosteps in the valley regions due to regular step structure deflect more TSDs/TMDs that then form mixed type (Shockley+Frank) stacking faults.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1190, 55-62
Open AccessInvestigation of Spoke Pattern of Stacking Faults in 4H-SiC Wafers Grown by Physical Vapor Transport Method
Synchrotron monochromatic beam X-ray topography (SMBXT), synchrotron white beam X-ray topography (SWBXT) and high-resolution X-ray topography (HRXRT) were used to characterize a series of wafers sliced from two PVT-grown 4H-SiC boules under similar growth conditions. A unique spoke-shaped distribution of the threading screw/mixed dislocations (TSDs/TMDs) density map can be observed from wafers sliced from later stages of growth of both boules. Systematic sequential analysis of the SMBXT grazing incidence images and HRXRT reflection images of the wafers reveals the spoke patterns are formed due to continuous deflection process of TSDs/TMDs by thin layer of polytypes that propagate along step flow direction and expand vertically, leading to TSD density difference across the wafer. Regions with high TSD densities have higher growth rate, resulting in a ridge and valley structure. Generation of macrosteps in the valley regions due to regular step structure deflect more TSDs/TMDs that then form mixed type (Shockley+Frank) stacking faults.
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 73-78
Observation and Analysis of the “Galaxy” Defect in 4H-SiC through X-Ray Synchrotron Topography
Silicon carbide (SiC) is valued for high-power and high-frequency devices, but its performance is limited by crystalline defects. We report a newly observed defect arrangement, termed the “galaxy” defect, in wafers from a PVT-grown 6-inch 4° off-axis boule. Optical microscopy revealed dense clusters of micron-sized inclusions, while synchrotron X-ray topography (XRT) showed associated dislocation networks. Transmission synchrotron XRT indicated threading dislocation clusters, and grazing images revealed high densities of basal plane dislocations, deflected Frank partials, and threading-edge-dislocation low-angle grain boundaries (TED-LAGBs). The defect evolved as growth progressed, producing increasingly complex dislocation structures. Based on the observation, we proposed a mechanism for the evolution of the defect involving the generation, evolution, and interaction between the inclusions and dislocations.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 73-78
Open AccessObservation and Analysis of the “Galaxy” Defect in 4H-SiC through X-Ray Synchrotron Topography
Silicon carbide (SiC) is valued for high-power and high-frequency devices, but its performance is limited by crystalline defects. We report a newly observed defect arrangement, termed the “galaxy” defect, in wafers from a PVT-grown 6-inch 4° off-axis boule. Optical microscopy revealed dense clusters of micron-sized inclusions, while synchrotron X-ray topography (XRT) showed associated dislocation networks. Transmission synchrotron XRT indicated threading dislocation clusters, and grazing images revealed high densities of basal plane dislocations, deflected Frank partials, and threading-edge-dislocation low-angle grain boundaries (TED-LAGBs). The defect evolved as growth progressed, producing increasingly complex dislocation structures. Based on the observation, we proposed a mechanism for the evolution of the defect involving the generation, evolution, and interaction between the inclusions and dislocations.
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 79-85
Growth and Characterization of High-Quality Thick Epitaxial 4H-SiC Wafers for High Voltage Devices
Silicon carbide is a leading wide-bandgap semiconductor for high-voltage power electronics. For 6.5–10 kV operation, thick epitaxial layers (≥60 µm) are required to sustain depletion width and maintain uniform electric fields, placing a premium on low extended-defect densities in both substrate and epilayer. Thick epitaxial 4H-SiC layers of 60 µm and 110 µm were grown on 6-inch substrates in a multi-wafer warm-wall reactor and evaluated by synchrotron X-ray topography in grazing-incidence (22-4 16) and transmission (11-20) geometries. Transmission imaging showed substrate dislocation content near the lower bound typically reported for 6-inch wafers. Notably, grazing-incidence topography (penetration depth >40 µm) revealed no basal-plane dislocations propagating into the epilayers, consistent with efficient dislocation conversion at the substrate–epilayer interface. The 3C-SiC inclusion density was ~30 per 6-inch wafer for 60 µm epilayers and ~60 per wafer for 110 µm epilayers; the average micropipes density varies from 0 to 5 for both 60 and 110 um epiwafers. Threading dislocation densities—screw, edge, and mixed—were on the order of 1.0–2.0 × 10³ cm⁻². These results establish thick 4H-SiC epilayers with suppressed basal-plane propagation and substantially reduced extended-defect content, providing a strong basis for reliable 6.5–10 kV device fabrication.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 79-85
Open AccessGrowth and Characterization of High-Quality Thick Epitaxial 4H-SiC Wafers for High Voltage Devices
Silicon carbide is a leading wide-bandgap semiconductor for high-voltage power electronics. For 6.5–10 kV operation, thick epitaxial layers (≥60 µm) are required to sustain depletion width and maintain uniform electric fields, placing a premium on low extended-defect densities in both substrate and epilayer. Thick epitaxial 4H-SiC layers of 60 µm and 110 µm were grown on 6-inch substrates in a multi-wafer warm-wall reactor and evaluated by synchrotron X-ray topography in grazing-incidence (22-4 16) and transmission (11-20) geometries. Transmission imaging showed substrate dislocation content near the lower bound typically reported for 6-inch wafers. Notably, grazing-incidence topography (penetration depth >40 µm) revealed no basal-plane dislocations propagating into the epilayers, consistent with efficient dislocation conversion at the substrate–epilayer interface. The 3C-SiC inclusion density was ~30 per 6-inch wafer for 60 µm epilayers and ~60 per wafer for 110 µm epilayers; the average micropipes density varies from 0 to 5 for both 60 and 110 um epiwafers. Threading dislocation densities—screw, edge, and mixed—were on the order of 1.0–2.0 × 10³ cm⁻². These results establish thick 4H-SiC epilayers with suppressed basal-plane propagation and substantially reduced extended-defect content, providing a strong basis for reliable 6.5–10 kV device fabrication.
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 59-64
High Quality P-Type 4H-SiC Growth by PVT Method
The fabrication of n-channel IGBTs is constrained by the low conductivity as well as poor quality of the p-type SiC substrate. This paper reports 6-inch high quality p-type 4H-SiC wafers achieved by PVT method. The wafers were examined by synchrotron X-ray topography indicating average defect densities are on par or better than commercial 6-inch n-type wafers. Large areas of the wafer, especially the middle region of the wafer is characterized by very low density of BPDs. The extent of prismatic slip due to radial thermal gradients is also vastly reduced compared to typical n-type wafers.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 59-64
Open AccessHigh Quality P-Type 4H-SiC Growth by PVT Method
The fabrication of n-channel IGBTs is constrained by the low conductivity as well as poor quality of the p-type SiC substrate. This paper reports 6-inch high quality p-type 4H-SiC wafers achieved by PVT method. The wafers were examined by synchrotron X-ray topography indicating average defect densities are on par or better than commercial 6-inch n-type wafers. Large areas of the wafer, especially the middle region of the wafer is characterized by very low density of BPDs. The extent of prismatic slip due to radial thermal gradients is also vastly reduced compared to typical n-type wafers.
- Open Access
- 14 February 2026
- Published by Elsevier in SSRN Electronic Journal
Synchrotron X-ray topography analysis of the distribution and formation mechanisms of low angle grain boundaries in PVT-Grown 4H-SiC Crystal
Analysis of the distribution and formation mechanisms of low-angle grain boundaries (LAGBs) in physical vapor transport (PVT) grown 4H-SiC crystals was conducted by synchrotron monochromatic beam x-ray topography (SMBXT) in conjunction with ray-tracing simulation of dislocation images. Threading edge dislocation (TED)-LAGB networks were observed inside the facet region and next to the facet. Identification of TED Burgers vectors is achieved by correlating the ray tracing simulation and the observed contrast configurations from topographs. The results suggest that the TED-LAGBs network in the facet region originates from misorientations between threading screw dislocations which act as growth centers in the region. The LAGB network next to the facet results from the interaction of growth fronts of horseshoe-shaped steps from small spikes from the facet. This network incorporates prismatic slip dislocations induced by radial temperature gradients. These findings provide a novel mechanism for TED-LAGB formation, correlating the spatial distribution and growth dynamics.
- 14 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynchrotron X-ray topography analysis of the distribution and formation mechanisms of low angle grain boundaries in PVT-Grown 4H-SiC Crystal
Analysis of the distribution and formation mechanisms of low-angle grain boundaries (LAGBs) in physical vapor transport (PVT) grown 4H-SiC crystals was conducted by synchrotron monochromatic beam x-ray topography (SMBXT) in conjunction with ray-tracing simulation of dislocation images. Threading edge dislocation (TED)-LAGB networks were observed inside the facet region and next to the facet. Identification of TED Burgers vectors is achieved by correlating the ray tracing simulation and the observed contrast configurations from topographs. The results suggest that the TED-LAGBs network in the facet region originates from misorientations between threading screw dislocations which act as growth centers in the region. The LAGB network next to the facet results from the interaction of growth fronts of horseshoe-shaped steps from small spikes from the facet. This network incorporates prismatic slip dislocations induced by radial temperature gradients. These findings provide a novel mechanism for TED-LAGB formation, correlating the spatial distribution and growth dynamics.
- 9 February 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 681
Stacking fault analysis for the early-stages of PVT growth of 4H-SiC crystals
- 9 February 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 681
Stacking fault analysis for the early-stages of PVT growth of 4H-SiC crystals
- Open Access
- 10 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 376, 11-18
Exploring the Influence of Implant Profile and Device Design on Basal Plane Dislocation Generation in 1.2kV 4H-SiC Power MOSFETs
Several 1.2kV 4H-SiC devices of various cell architectures have been successfully fabricated by employing different P+ implantation conditions, resulting in varying levels of Basal Plane Dislocation (BPD) densities across the different device designs. It was found that by utilizing devices designed with an orthogonal P+ source layout as opposed to the traditional P+ stripe pattern, the long-term reliability under sustained 3rd Quadrant current stress conduction can be greatly improved even in devices with medium BPD densities. In addition, the use of the unipolar current of the JBSFET can further enhance long-term reliability under sustained 3rd Quadrant current stress by mitigating stacking fault expansion, even in devices with a high BPD density.
- 10 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 376, 11-18
Open AccessExploring the Influence of Implant Profile and Device Design on Basal Plane Dislocation Generation in 1.2kV 4H-SiC Power MOSFETs
Several 1.2kV 4H-SiC devices of various cell architectures have been successfully fabricated by employing different P+ implantation conditions, resulting in varying levels of Basal Plane Dislocation (BPD) densities across the different device designs. It was found that by utilizing devices designed with an orthogonal P+ source layout as opposed to the traditional P+ stripe pattern, the long-term reliability under sustained 3rd Quadrant current stress conduction can be greatly improved even in devices with medium BPD densities. In addition, the use of the unipolar current of the JBSFET can further enhance long-term reliability under sustained 3rd Quadrant current stress by mitigating stacking fault expansion, even in devices with a high BPD density.
- Open Access
- 10 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 376, 1-9
Punching of Prismatic Dislocation Loops from Inclusions in 4H-SiC Wafers
Indentation behavior induced by the presence of foreign inclusions in a PVT-grown 4H-SiC wafer is investigated through synchrotron X-ray topography, which revealed the generation of dislocation arrays from the inclusion center along six directions. Grazing-incident topographs shows these dislocation arrays exhibit contrast configurations of opposite-signed TED pairs or BPD segments. This correlates with dislocation loops generated due to prismatic punching, and dislocation configuration variation is dependent on the position of prismatic loops with respect to the wafer surface. The stress induced by the inclusion embedded in the 4H-SiC matrix is estimated from the difference in the thermomechanical properties, as the crystal is cooled from the growth temperature.
- 10 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 376, 1-9
Open AccessPunching of Prismatic Dislocation Loops from Inclusions in 4H-SiC Wafers
Indentation behavior induced by the presence of foreign inclusions in a PVT-grown 4H-SiC wafer is investigated through synchrotron X-ray topography, which revealed the generation of dislocation arrays from the inclusion center along six directions. Grazing-incident topographs shows these dislocation arrays exhibit contrast configurations of opposite-signed TED pairs or BPD segments. This correlates with dislocation loops generated due to prismatic punching, and dislocation configuration variation is dependent on the position of prismatic loops with respect to the wafer surface. The stress induced by the inclusion embedded in the 4H-SiC matrix is estimated from the difference in the thermomechanical properties, as the crystal is cooled from the growth temperature.
- Open Access
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 375, 35-41
Formation Mechanism and Complex Faulting Behavior of a BPD Loop in 180 μm Thick 4H-SiC Epitaxial Layer
4H-SiC with 180 μm epilayer was subjected to UV exposure. Stacking fault expanded from basal plane dislocation (BPD) loop generated during growth in the epilayer was observed by UV Photoluminescence Imaging (UVPL) and X-ray Topograph (XRT) techniques. Interactions between partial dislocation, emanating from the BPD loop and gliding via recombination-enhanced dislocation glide mechanism, and threading screw/mix dislocations are detected and analyzed, where stacking faults migrate to different basal plane after the interactions. Such migration increases the faulted volume that can severely degrade reliability and performance of high power SiC devices by increasing reverse leakage current and on-state resistance and could eventually lead to device failure.
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 375, 35-41
Open AccessFormation Mechanism and Complex Faulting Behavior of a BPD Loop in 180 μm Thick 4H-SiC Epitaxial Layer
4H-SiC with 180 μm epilayer was subjected to UV exposure. Stacking fault expanded from basal plane dislocation (BPD) loop generated during growth in the epilayer was observed by UV Photoluminescence Imaging (UVPL) and X-ray Topograph (XRT) techniques. Interactions between partial dislocation, emanating from the BPD loop and gliding via recombination-enhanced dislocation glide mechanism, and threading screw/mix dislocations are detected and analyzed, where stacking faults migrate to different basal plane after the interactions. Such migration increases the faulted volume that can severely degrade reliability and performance of high power SiC devices by increasing reverse leakage current and on-state resistance and could eventually lead to device failure.