MKMaxim Karasev

Maxim Karasev

*This is an algorithmically generated author record based on publicly available information.

Maxim Karasev has a total of 12 co-authors. Here are the top co-authors by number of shared publications:

  • Nikita Andreevich Belyakov

    Saint-Petersburg Mining University, Faculty of Civil Engineering, No. 1, 21 line, 2. St. Petersburg, 199026, Russia

    2 shared publications
  • Alexander A. Selikhov

    Department of Construction of Mining Enterprises and Underground Structures, Empress Catherine II St. Petersburg Mining University, 21st Line 2, 199106 St. Petersburg, Russia

    1 shared publication
  • Anna Andreeva

    Department of Construction of Mining Enterprises and Underground Structures, Empress Catherine II St. Petersburg Mining University, 21st Line 2, 199106 St. Petersburg, Russia

    1 shared publication
  • Egor S. Kudashov

    Laboratory of Physical and Mechanical Properties and Rock Fracture of the Scientific Center for Geomechanics and Mining Problems, Empress Catherine II St. Petersburg Mining University, 21st Line 2, 199106 St. Petersburg, Russia

    1 shared publication
  • Ekaterina L. Romanova

    Department of Industrial and Civil Engineering, Empress Catherine II St. Petersburg Mining University, 21st Line 2, 199106 St. Petersburg, Russia

    1 shared publication
  • Grigirii Iovlev

    Department of underground structures and mine construction, Saint-Petersburg Mining University 21 line of V. O., 2, Saint-Petersburg, Russia, 199106

    1 shared publication

Latest Publications

  • Open Access

    Features of Modeling the Mechanical Response of Crushed Salt-Based Backfill Material in Potash Mines

    by Alexander A. Selikhov, Maxim A. Karasev, Vladislav V. Petrushin, Ekaterina L. Romanova, Anna V. Andreeva, Vadim S. Biberin, Egor S. Kudashov

    The development of potash deposits under complex mining and geological conditions requires the implementation of efficient geotechnologies, including backfilling of mined-out voids. Preserving the water-protective strata and preventing mining-induced accidents are impossible without accurate prediction of the stress–strain state of the backfill mass. Traditional models, based on the Mohr–Coulomb criterion, are unable to properly describe physical and mechanical processes occurring in crushed salt rock, including the transition from dilatancy to compaction and nonlinear hardening. This requires the application of specialized models such as the SRP model. The aim of this study is to investigate the mechanical response of crushed salt rock backfill material under complex loading conditions and to calibrate the parameters of the SRP model in order to improve the accuracy of geomechanical calculations. The shape of the plastic flow surface in the deviatoric plane was established, including both shear and cap components. A nonlinear dependence of the friction angle on mean stress was identified and described by a logarithmic function. The law of plastic hardening was determined, and a non-associated plastic flow rule was confirmed in the shear domain. The calibrated SRP model allows for predicting the backfill mass behavior with high reliability, which is a necessary condition for substantiating the parameters of safe potash mining.

  • Open Access

    Assessment of the Influence of Formation Conditions of Embankments and Spoil Heaps on Their Stability When Dumped on Clay-Salt Slurries

    by Maxim Karasev, Tatsiana Astapenka

    The formation of geotechnical structures on foundations composed of low-strength soils is associated with a number of risks and difficulties. Soils such as clay-salt slurries are characterized by low bearing capacity and a tendency to deform under load. In this study, a numerical simulation of the stability analysis of an embankment constructed on low-strength soils consisting of clay-salt slurries is carried out, and the study of the dependence of the stability and behavior of the embankment on the configuration of this foundation, without taking into account the embedment of rocks and with introduction of rocks into the geotechnical system, is considered. The results prove that the sloping configuration of low-strength soils greatly complicates the stability of the embankment. It is noted that the stability factor is significantly reduced under the influence of loads on low-strength soil, particularly when the geotechnical system has a configuration with slope angles of 5° and 10°, and, in addition, when rocks are embedded in low-strength soil if the underlying soil layer is a weak foundation. In view of this, the assessment of embankment stability on clay-salt slurries requires careful analysis due to a number of specific characteristics of these soils that create complex geotechnical conditions.


  • Face Stability in Heavy Clay: Theory and Practice

    by M. O. Lebedev, M. A. Karasev, N. A. Belyakov, L. A. Basova

    The authors focus on feasibility of reducing deformation of surrounding rock mass around underground structures by means of advanced reinforcement of tunnel faces in claystone. The reinforcement efficiency is estimated in 3D calculations. The factors to influence deformation in rock mass ahead of a tunnel faces include: rock bolt length, rock bolting system stiffness and the bolt pattern. An additional factor of concern is the mechanical characteristics of claystone. The implemented research shows the highest influence is exerted on deformation in rock mass by the bolt pattern and the rock bolting system stiffness. The efficient design of advanced rock bolting is determined.


  • EXPERIMENTAL AND NUMERICAL RESEARCH OF JOINTED ROCK MASS ANISOTROPY IN A THREE-DIMENSIONAL STRESS FIELD

    by Pavel Verbilo, Maxim Karasev, Nikita Belyakov, Grigirii Iovlev

    Joints often have a significant influence on material characteristics. The discontinuities’ coalescence mechanism and complex jointed rock mass structure as a composite need to be further explored. In this study, compression and shear tests were carried out on a jointed rock mass. The purpose of the jointed rock mass behaviour study was to determine the deformation-strength dependencies and to determine the parameters for a quantitative assessment of the joints’ influence on mechanical characteristics. The results show that compression strength depends on the materials’ structure, and there is a detailed description of the joints’ orientation influence on stress-strain dependencies during compression experiments. The numerical method used in this study could be used for the modelling of composite materials and their properties.