Reza Valizadeh
Research Subjects
Research Interests
Reza Valizadeh has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Oleg. B. Malyshev
STFC Daresbury Laboratory, Warrington Cheshire WA4 4AD, UK
3 shared publications - Arturs Medvids
Insitute of Technical Physics, Riga Technical University, Paula Valdena 3/7, 1048 Riga, Latvia
2 shared publications - Pavels Onufrijevs
Riga Technical University
2 shared publications A. Bousetta
Department of Electronic and Electrical Engineering, University of Salford, Salford M5 4WT UK
1 shared publicationA. Žunda
Institute of Power and Transport Machinery Engineering, Vytautas Magnus University, 11 Studentų Str., Kaunas LT-53362, Lithuania
1 shared publicationChe-Kai Chan
1 shared publication
Latest Publications
- 2 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Numerical Calculation of Magnetic Field Enhancement and Impact of Surface Defects on Premature Entry of Magnetic Field in Thin Nb Films for SRF Cavities
In this work, we have investigated two series of Nb/Cu samples deposited by HiPIMS technique, and differing in Nb deposition conditions, Nb film thickness and Cu substrate polishing techniques. All the films were additionally irradiated by Nd:YAG laser to smooth their surfaces. The impact of the magnetic field enhancement at the surface defects on the premature start of magnetic field penetration into the superconducting film was studied, combining experiments and numerical calculations. Compared to previous study, improved numerical calculations by using the Finite Element Method (FEM) served to calculate the maximum field enhancement factor β m , reflecting impact of the most crucial surface defects found in the samples. Magnetization measurements at 4.2 K in DC magnetic field, oriented parallel to the film, were employed to determine the start of the field penetration H en . The SEM and AFM analyses served to investigate the Nb surface morphology. In some samples, deviations from the H en (β m ) dependence were observed. It was found that the magnetic field penetration could start from the Nb/Cu interface rather than from the free Nb surface due to visibly better quality of the free Nb surface observed by SEM analysis, and that could lead to the deterioration of H en (β m ) dependence.
- 2 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Numerical Calculation of Magnetic Field Enhancement and Impact of Surface Defects on Premature Entry of Magnetic Field in Thin Nb Films for SRF Cavities
In this work, we have investigated two series of Nb/Cu samples deposited by HiPIMS technique, and differing in Nb deposition conditions, Nb film thickness and Cu substrate polishing techniques. All the films were additionally irradiated by Nd:YAG laser to smooth their surfaces. The impact of the magnetic field enhancement at the surface defects on the premature start of magnetic field penetration into the superconducting film was studied, combining experiments and numerical calculations. Compared to previous study, improved numerical calculations by using the Finite Element Method (FEM) served to calculate the maximum field enhancement factor β m , reflecting impact of the most crucial surface defects found in the samples. Magnetization measurements at 4.2 K in DC magnetic field, oriented parallel to the film, were employed to determine the start of the field penetration H en . The SEM and AFM analyses served to investigate the Nb surface morphology. In some samples, deviations from the H en (β m ) dependence were observed. It was found that the magnetic field penetration could start from the Nb/Cu interface rather than from the free Nb surface due to visibly better quality of the free Nb surface observed by SEM analysis, and that could lead to the deterioration of H en (β m ) dependence.
- Open Access
- 20 July 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (9) , 095004
A facility for the characterisation of planar multilayer structures with preliminary niobium results
The maximum accelerating gradient of superconducting radio frequency cavities are currently reaching their theoretical limits, due to the magnetic field entering the superconductor in the form of vortices. To overcome these limits, thin film coated superconducting materials are required, however these need to be tested to optimise their properties. A system has been designed, built, and commissioned at Daresbury Laboratory that applies a local DC magnetic field parallel to the surface, from one side of a sample, similar to that in cavity operation. A magnetic flux density (up to 600 mT) is generated parallel to the sample surface in the 2 mm gap of a C-shaped ferrite yoke. Two Hall probe sensors are used to measure both the applied and penetrated magnetic field. The system operates in a cryogen free environment, with a minimum temperature of approximately 2.6 K. A Pb foil has been used to characterise the system, and determine how the sample size affects the results. Nb thin film samples have been tested for varying thickness to determine how the depth effects the field of full flux penetration, B f p . The design, operation, methods of analysis and first results of this facility will be reported in this paper.
- 20 July 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (9) , 095004
Open AccessA facility for the characterisation of planar multilayer structures with preliminary niobium results
The maximum accelerating gradient of superconducting radio frequency cavities are currently reaching their theoretical limits, due to the magnetic field entering the superconductor in the form of vortices. To overcome these limits, thin film coated superconducting materials are required, however these need to be tested to optimise their properties. A system has been designed, built, and commissioned at Daresbury Laboratory that applies a local DC magnetic field parallel to the surface, from one side of a sample, similar to that in cavity operation. A magnetic flux density (up to 600 mT) is generated parallel to the sample surface in the 2 mm gap of a C-shaped ferrite yoke. Two Hall probe sensors are used to measure both the applied and penetrated magnetic field. The system operates in a cryogen free environment, with a minimum temperature of approximately 2.6 K. A Pb foil has been used to characterise the system, and determine how the sample size affects the results. Nb thin film samples have been tested for varying thickness to determine how the depth effects the field of full flux penetration, B f p . The design, operation, methods of analysis and first results of this facility will be reported in this paper.
- Open Access
- 1 June 2022
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 31 (6) , 065002
Ion energy analysis of a bipolar HiPIMS discharge using a retarding field energy analyser
The time evolution of the positive ion energy distribution functions (IEDF’s) at the substrate position in an asymmetric bipolar high-power impulse magnetron sputtering (HiPIMS) system was determined using a gridded energy analyser. This was done for a range of operating conditions, namely the positive voltage U rev and ‘on-time’ negative pulse duration τ neg. The magnetron sputtering discharge was equipped with a Nb target. Based on the knowledge of the IEDF’s, the bombarding ion flux density Γi and energy flux density Q i to a grounded surface were calculated. Time-resolved IEDF measurements showed that ions with energies approaching the equivalent of the positive pulse voltage U rev were generated as the reverse positive voltage phase developed. On time-average, we observed that increasing the set U rev value (from 0 to 100 V), resulted in a marginal decrease in the ion flux density Γi to the analyser. However, this is accompanied by a five-fold increase in the ion energy flux density Q i compared to the unipolar, U rev = 0 V case. Reducing the negative HiPIMS pulse duration τ neg (from 130 to 40 μs) at a constant discharge power leads to a modest increase in Γi, but a four-fold increase in Q i. The results reveal the benefit of the bipolar HiPIMS technique, in which it is possible to control and enhance the power density of ions bombarding a grounded (or fixed bias) substrate, for potentially better tailoring of thin film properties.
- 1 June 2022
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 31 (6) , 065002
Open AccessIon energy analysis of a bipolar HiPIMS discharge using a retarding field energy analyser
The time evolution of the positive ion energy distribution functions (IEDF’s) at the substrate position in an asymmetric bipolar high-power impulse magnetron sputtering (HiPIMS) system was determined using a gridded energy analyser. This was done for a range of operating conditions, namely the positive voltage U rev and ‘on-time’ negative pulse duration τ neg. The magnetron sputtering discharge was equipped with a Nb target. Based on the knowledge of the IEDF’s, the bombarding ion flux density Γi and energy flux density Q i to a grounded surface were calculated. Time-resolved IEDF measurements showed that ions with energies approaching the equivalent of the positive pulse voltage U rev were generated as the reverse positive voltage phase developed. On time-average, we observed that increasing the set U rev value (from 0 to 100 V), resulted in a marginal decrease in the ion flux density Γi to the analyser. However, this is accompanied by a five-fold increase in the ion energy flux density Q i compared to the unipolar, U rev = 0 V case. Reducing the negative HiPIMS pulse duration τ neg (from 130 to 40 μs) at a constant discharge power leads to a modest increase in Γi, but a four-fold increase in Q i. The results reveal the benefit of the bipolar HiPIMS technique, in which it is possible to control and enhance the power density of ions bombarding a grounded (or fixed bias) substrate, for potentially better tailoring of thin film properties.
- 1 September 2020
- Published by Elsevier in Applied Surface Science
- Vol. 525, 146528
Improvement of Nb/Cu adhesion and increase of Nb crystal size by laser radiation
- 1 September 2020
- Published by Elsevier in Applied Surface Science
- Vol. 525, 146528
Improvement of Nb/Cu adhesion and increase of Nb crystal size by laser radiation
- 6 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 65 (9) , 2620-2627
The Effect of Air Exposure on SEY and Surface Composition of Laser Treated Copper Applied in Accelerators
In this paper, the effect of air exposure and acetone cleaning on the secondary electron yield (SEY) of laser treated copper applied in accelerators for the inhibition of electron cloud was investigated and discussed. The SEY of laser treated copper samples after acetone cleaning and air exposure was measured. After 10-21 months air exposure, the maximum SEY increased by about 11%-20%. Furthermore, changes of carbon, copper, and oxygen chemistry states from sample surface after acetone and air exposure were studied by means of X-ray photoelectron spectroscopy. The XPS results show that the concentration of Cu from the surface of the samples with the thickness of 500 and 20 μm decreased by about 61%-70% after acetone cleaning and decreased by a further 36%-70% after 10-21 months air exposure. Moreover, the XPS measurement reflects the significant increase of the total percentages of C and O after acetone cleaning, and further increase after 10-21 months air exposure. The increase of SEY is explained in terms of the introduction of impurities, such as oxide and carbide.
- 6 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 65 (9) , 2620-2627
The Effect of Air Exposure on SEY and Surface Composition of Laser Treated Copper Applied in Accelerators
In this paper, the effect of air exposure and acetone cleaning on the secondary electron yield (SEY) of laser treated copper applied in accelerators for the inhibition of electron cloud was investigated and discussed. The SEY of laser treated copper samples after acetone cleaning and air exposure was measured. After 10-21 months air exposure, the maximum SEY increased by about 11%-20%. Furthermore, changes of carbon, copper, and oxygen chemistry states from sample surface after acetone and air exposure were studied by means of X-ray photoelectron spectroscopy. The XPS results show that the concentration of Cu from the surface of the samples with the thickness of 500 and 20 μm decreased by about 61%-70% after acetone cleaning and decreased by a further 36%-70% after 10-21 months air exposure. Moreover, the XPS measurement reflects the significant increase of the total percentages of C and O after acetone cleaning, and further increase after 10-21 months air exposure. The increase of SEY is explained in terms of the introduction of impurities, such as oxide and carbide.